From: Parker Newman <pnewman@xxxxxxxxxxxxxxx> This patch adds a quirk similar to eeprom_93xx46 to add an extra clock cycle before reading data from the EEPROM. The 93Cx6 family of EEPROMs output a "dummy 0 bit" between the writing of the op-code/address from the host to the EEPROM and the reading of the actual data from the EEPROM. More info can be found on page 6 of the AT93C46 datasheet. Similar notes are found in other 93xx6 datasheets. Link: https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-5193-SEEPROM-AT93C46D-Datasheet.pdf In summary the read operation for a 93Cx6 EEPROM is: Write to EEPROM : 110[A5-A0] (9 bits) Read from EEPROM: 0[D15-D0] (17 bits) Where: 110 is the start bit and READ OpCode [A5-A0] is the address to read from 0 is a "dummy bit" preceding the actual data [D15-D0] is the actual data. Looking at the READ timing diagrams in the 93Cx6 datasheets the dummy bit should be clocked out on the last address bit clock cycle meaning it should be discarded naturally. However, depending on the hardware configuration sometimes this dummy bit is not discarded. This is the case with Exar PCI UARTs which require an extra clock cycle between sending the address and reading the data. Signed-off-by: Parker Newman <pnewman@xxxxxxxxxxxxxxx> --- drivers/misc/eeprom/eeprom_93cx6.c | 15 +++++++++++++++ include/linux/eeprom_93cx6.h | 7 +++++++ 2 files changed, 22 insertions(+) diff --git a/drivers/misc/eeprom/eeprom_93cx6.c b/drivers/misc/eeprom/eeprom_93cx6.c index 9627294fe3e9..0f52d3c4bc1d 100644 --- a/drivers/misc/eeprom/eeprom_93cx6.c +++ b/drivers/misc/eeprom/eeprom_93cx6.c @@ -18,6 +18,11 @@ MODULE_VERSION("1.0"); MODULE_DESCRIPTION("EEPROM 93cx6 chip driver"); MODULE_LICENSE("GPL"); +static inline bool has_quirk_extra_read_cycle(struct eeprom_93cx6 *eeprom) +{ + return eeprom->quirks & PCI_EEPROM_QUIRK_EXTRA_READ_CYCLE; +} + static inline void eeprom_93cx6_pulse_high(struct eeprom_93cx6 *eeprom) { eeprom->reg_data_clock = 1; @@ -186,6 +191,11 @@ void eeprom_93cx6_read(struct eeprom_93cx6 *eeprom, const u8 word, eeprom_93cx6_write_bits(eeprom, command, PCI_EEPROM_WIDTH_OPCODE + eeprom->width); + if (has_quirk_extra_read_cycle(eeprom)) { + eeprom_93cx6_pulse_high(eeprom); + eeprom_93cx6_pulse_low(eeprom); + } + /* * Read the requested 16 bits. */ @@ -252,6 +262,11 @@ void eeprom_93cx6_readb(struct eeprom_93cx6 *eeprom, const u8 byte, eeprom_93cx6_write_bits(eeprom, command, PCI_EEPROM_WIDTH_OPCODE + eeprom->width + 1); + if (has_quirk_extra_read_cycle(eeprom)) { + eeprom_93cx6_pulse_high(eeprom); + eeprom_93cx6_pulse_low(eeprom); + } + /* * Read the requested 8 bits. */ diff --git a/include/linux/eeprom_93cx6.h b/include/linux/eeprom_93cx6.h index c860c72a921d..5274bcc7ca39 100644 --- a/include/linux/eeprom_93cx6.h +++ b/include/linux/eeprom_93cx6.h @@ -11,6 +11,8 @@ Supported chipsets: 93c46, 93c56 and 93c66. */ +#include <linux/bits.h> + /* * EEPROM operation defines. */ @@ -25,6 +27,9 @@ #define PCI_EEPROM_EWDS_OPCODE 0x10 #define PCI_EEPROM_EWEN_OPCODE 0x13 +/* Some EEPROMs require an extra clock cycle before reading */ +#define PCI_EEPROM_QUIRK_EXTRA_READ_CYCLE BIT(0) + /** * struct eeprom_93cx6 - control structure for setting the commands * for reading the eeprom data. @@ -34,6 +39,7 @@ * @register_write(struct eeprom_93cx6 *eeprom): handler to * write to the eeprom register by using all reg_* fields. * @width: eeprom width, should be one of the PCI_EEPROM_WIDTH_* defines + * @quirks: eeprom or controller quirk bitfield * @drive_data: Set if we're driving the data line. * @reg_data_in: register field to indicate data input * @reg_data_out: register field to indicate data output @@ -50,6 +56,7 @@ struct eeprom_93cx6 { void (*register_write)(struct eeprom_93cx6 *eeprom); int width; + unsigned int quirks; char drive_data; char reg_data_in; -- 2.46.0
