The container of the struct dw8250_port_data is private to the actual
driver. In particular, 8250_lpss and 8250_dw use different data types
that are assigned to the UART port private_data. Hence, it must not
be used outside the specific driver.
Currently the only cpr_val is required by the common code, make it
be available via struct dw8250_port_data.
This fixes the UART breakage on Intel Galileo boards.
Fixes: 593dea000bc1 ("serial: 8250: dw: Allow to use a fallback CPR value if not synthesized")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
---
drivers/tty/serial/8250/8250_dw.c | 9 +++++++--
drivers/tty/serial/8250/8250_dwlib.c | 3 +--
drivers/tty/serial/8250/8250_dwlib.h | 3 ++-
3 files changed, 10 insertions(+), 5 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index 1300c92b8702..94d680e4b535 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -55,6 +55,7 @@
#define DW_UART_QUIRK_SKIP_SET_RATE BIT(2)
#define DW_UART_QUIRK_IS_DMA_FC BIT(3)
#define DW_UART_QUIRK_APMC0D08 BIT(4)
+#define DW_UART_QUIRK_CPR_VALUE BIT(5)
static inline struct dw8250_data *clk_to_dw8250_data(struct notifier_block *nb)
{
@@ -445,6 +446,10 @@ static void dw8250_prepare_rx_dma(struct uart_8250_port *p)
static void dw8250_quirks(struct uart_port *p, struct dw8250_data *data)
{
unsigned int quirks = data->pdata ? data->pdata->quirks : 0;
+ u32 cpr_value = data->pdata ? data->pdata->cpr_value : 0;
+
+ if (quirks & DW_UART_QUIRK_CPR_VALUE)
+ data->data.cpr_value = cpr_value;
#ifdef CONFIG_64BIT
if (quirks & DW_UART_QUIRK_OCTEON) {
@@ -727,8 +732,8 @@ static const struct dw8250_platform_data dw8250_armada_38x_data = {
static const struct dw8250_platform_data dw8250_renesas_rzn1_data = {
.usr_reg = DW_UART_USR,
- .cpr_val = 0x00012f32,
- .quirks = DW_UART_QUIRK_IS_DMA_FC,
+ .cpr_value = 0x00012f32,
+ .quirks = DW_UART_QUIRK_CPR_VALUE | DW_UART_QUIRK_IS_DMA_FC,
};
static const struct dw8250_platform_data dw8250_starfive_jh7100_data = {
diff --git a/drivers/tty/serial/8250/8250_dwlib.c b/drivers/tty/serial/8250/8250_dwlib.c
index 3e33ddf7bc80..5a2520943dfd 100644
--- a/drivers/tty/serial/8250/8250_dwlib.c
+++ b/drivers/tty/serial/8250/8250_dwlib.c
@@ -242,7 +242,6 @@ static const struct serial_rs485 dw8250_rs485_supported = {
void dw8250_setup_port(struct uart_port *p)
{
struct dw8250_port_data *pd = p->private_data;
- struct dw8250_data *data = to_dw8250_data(pd);
struct uart_8250_port *up = up_to_u8250p(p);
u32 reg, old_dlf;
@@ -278,7 +277,7 @@ void dw8250_setup_port(struct uart_port *p)
reg = dw8250_readl_ext(p, DW_UART_CPR);
if (!reg) {
- reg = data->pdata->cpr_val;
+ reg = pd->cpr_value;
dev_dbg(p->dev, "CPR is not available, using 0x%08x instead\n", reg);
}
if (!reg)
diff --git a/drivers/tty/serial/8250/8250_dwlib.h b/drivers/tty/serial/8250/8250_dwlib.h
index f13e91f2cace..794a9014cdac 100644
--- a/drivers/tty/serial/8250/8250_dwlib.h
+++ b/drivers/tty/serial/8250/8250_dwlib.h
@@ -19,6 +19,7 @@ struct dw8250_port_data {
struct uart_8250_dma dma;
/* Hardware configuration */
+ u32 cpr_value;
u8 dlf_size;
/* RS485 variables */
@@ -27,7 +28,7 @@ struct dw8250_port_data {
struct dw8250_platform_data {
u8 usr_reg;
- u32 cpr_val;
+ u32 cpr_value;
unsigned int quirks;
};
--
2.43.0.rc1.1336.g36b5255a03ac
