We are not supposed to spread quirks in 8250_port module especially
when we have a separate driver for the hardware in question.
Move quirk from generic module to the driver that uses it.
While at it, move IO to ->set_divisor() callback as it has to be from
day 1. ->get_divisor() is not supposed to perform any IO as UART port:
- might not be powered on
- is not locked by a spin lock
Fixes: 1ed67ecd1349 ("8250: microchip: Add 4 Mbps support in PCI1XXXX UART")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
---
drivers/tty/serial/8250/8250_pci1xxxx.c | 25 ++++++++++++++++++-------
drivers/tty/serial/8250/8250_port.c | 6 ------
2 files changed, 18 insertions(+), 13 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_pci1xxxx.c b/drivers/tty/serial/8250/8250_pci1xxxx.c
index 55eada1dba56..2fbb5851f788 100644
--- a/drivers/tty/serial/8250/8250_pci1xxxx.c
+++ b/drivers/tty/serial/8250/8250_pci1xxxx.c
@@ -94,7 +94,6 @@
#define UART_BIT_SAMPLE_CNT_16 16
#define BAUD_CLOCK_DIV_INT_MSK GENMASK(31, 8)
#define ADCL_CFG_RTS_DELAY_MASK GENMASK(11, 8)
-#define UART_CLOCK_DEFAULT (62500 * HZ_PER_KHZ)
#define UART_WAKE_REG 0x8C
#define UART_WAKE_MASK_REG 0x90
@@ -227,13 +226,10 @@ static unsigned int pci1xxxx_get_divisor(struct uart_port *port,
unsigned int uart_sample_cnt;
unsigned int quot;
- if (baud >= UART_BAUD_4MBPS) {
+ if (baud >= UART_BAUD_4MBPS)
uart_sample_cnt = UART_BIT_SAMPLE_CNT_8;
- writel(UART_BIT_DIVISOR_8, (port->membase + FRAC_DIV_CFG_REG));
- } else {
+ else
uart_sample_cnt = UART_BIT_SAMPLE_CNT_16;
- writel(UART_BIT_DIVISOR_16, (port->membase + FRAC_DIV_CFG_REG));
- }
/*
* Calculate baud rate sampling period in nanoseconds.
@@ -249,6 +245,11 @@ static unsigned int pci1xxxx_get_divisor(struct uart_port *port,
static void pci1xxxx_set_divisor(struct uart_port *port, unsigned int baud,
unsigned int quot, unsigned int frac)
{
+ if (baud >= UART_BAUD_4MBPS)
+ writel(UART_BIT_DIVISOR_8, port->membase + FRAC_DIV_CFG_REG);
+ else
+ writel(UART_BIT_DIVISOR_16, port->membase + FRAC_DIV_CFG_REG);
+
writel(FIELD_PREP(BAUD_CLOCK_DIV_INT_MSK, quot) | frac,
port->membase + UART_BAUD_CLK_DIVISOR_REG);
}
@@ -619,6 +620,17 @@ static int pci1xxxx_setup(struct pci_dev *pdev,
port->port.flags |= UPF_FIXED_TYPE | UPF_SKIP_TEST;
port->port.type = PORT_MCHP16550A;
+ /*
+ * 8250 core considers prescaller value to be always 16.
+ * The MCHP ports support downscaled mode and hence the
+ * functional UART clock can be lower, i.e. 62.5MHz, than
+ * software expects in order to support higher baud rates.
+ * Assign here 64MHz to support 4Mbps.
+ *
+ * The value itself is not really used anywhere except baud
+ * rate calculations, so we can mangle it as we wish.
+ */
+ port->port.uartclk = 64 * HZ_PER_MHZ;
port->port.set_termios = serial8250_do_set_termios;
port->port.get_divisor = pci1xxxx_get_divisor;
port->port.set_divisor = pci1xxxx_set_divisor;
@@ -732,7 +744,6 @@ static int pci1xxxx_serial_probe(struct pci_dev *pdev,
memset(&uart, 0, sizeof(uart));
uart.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT;
- uart.port.uartclk = UART_CLOCK_DEFAULT;
uart.port.dev = dev;
if (num_vectors == max_vec_reqd)
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index c37905ea3cae..d59dc219c899 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -2699,12 +2699,6 @@ static unsigned int serial8250_get_baud_rate(struct uart_port *port,
max = (port->uartclk + tolerance) / 16;
}
- /*
- * Microchip PCI1XXXX UART supports maximum baud rate up to 4 Mbps
- */
- if (up->port.type == PORT_MCHP16550A)
- max = 4000000;
-
/*
* Ask the core to calculate the divisor for us.
* Allow 1% tolerance at the upper limit so uart clks marginally
--
2.43.0.rc1.1.gbec44491f096
