pci1xxxx_handle_irq reads the burst status and checks if the FIFO
is empty and is ready to accept the incoming data. The handling is
done in pci1xxxx_tx_burst where each transaction processes data in
block of DWORDs, while any remaining bytes are processed individually,
one byte at a time.
Signed-off-by: Rengarajan S <rengarajan.s@xxxxxxxxxxxxx>
---
drivers/tty/serial/8250/8250_pci1xxxx.c | 106 ++++++++++++++++++++++++
1 file changed, 106 insertions(+)
diff --git a/drivers/tty/serial/8250/8250_pci1xxxx.c b/drivers/tty/serial/8250/8250_pci1xxxx.c
index 558c4c7f3104..d53605bf908d 100644
--- a/drivers/tty/serial/8250/8250_pci1xxxx.c
+++ b/drivers/tty/serial/8250/8250_pci1xxxx.c
@@ -67,6 +67,7 @@
#define SYSLOCK_RETRY_CNT 1000
#define UART_RX_BYTE_FIFO 0x00
+#define UART_TX_BYTE_FIFO 0x00
#define UART_FIFO_CTL 0x02
#define UART_ACTV_REG 0x11
@@ -100,6 +101,7 @@
#define UART_RESET_D3_RESET_DISABLE BIT(16)
#define UART_BURST_STATUS_REG 0x9C
+#define UART_TX_BURST_FIFO 0xA0
#define UART_RX_BURST_FIFO 0xA4
#define MAX_PORTS 4
@@ -109,6 +111,7 @@
#define UART_BURST_SIZE 4
#define UART_BST_STAT_RX_COUNT_MASK 0x00FF
+#define UART_BST_STAT_TX_COUNT_MASK 0xFF00
#define UART_BST_STAT_IIR_INT_PEND 0x100000
#define UART_LSR_OVERRUN_ERR_CLR 0x43
#define UART_BST_STAT_LSR_RX_MASK 0x9F000000
@@ -116,6 +119,7 @@
#define UART_BST_STAT_LSR_OVERRUN_ERR 0x2000000
#define UART_BST_STAT_LSR_PARITY_ERR 0x4000000
#define UART_BST_STAT_LSR_FRAME_ERR 0x8000000
+#define UART_BST_STAT_LSR_THRE 0x20000000
struct pci1xxxx_8250 {
unsigned int nr;
@@ -344,6 +348,105 @@ static void pci1xxxx_rx_burst(struct uart_port *port, u32 uart_status)
}
}
+static void pci1xxxx_process_write_data(struct uart_port *port,
+ struct circ_buf *xmit,
+ int *data_empty_count,
+ u32 *valid_byte_count)
+{
+ u32 valid_burst_count = *valid_byte_count / UART_BURST_SIZE;
+
+ /*
+ * Each transaction transfers data in DWORDs. If there are less than
+ * four remaining valid_byte_count to transfer or if the circular
+ * buffer has insufficient space for a DWORD, the data is transferred
+ * one byte at a time.
+ */
+ while (valid_burst_count) {
+ if (*data_empty_count - UART_BURST_SIZE < 0)
+ break;
+ if (xmit->tail > (UART_XMIT_SIZE - UART_BURST_SIZE))
+ break;
+ writel(*(unsigned int *)&xmit->buf[xmit->tail],
+ port->membase + UART_TX_BURST_FIFO);
+ *valid_byte_count -= UART_BURST_SIZE;
+ *data_empty_count -= UART_BURST_SIZE;
+ valid_burst_count -= UART_BYTE_SIZE;
+
+ xmit->tail = (xmit->tail + UART_BURST_SIZE) &
+ (UART_XMIT_SIZE - 1);
+ }
+
+ while (*valid_byte_count) {
+ if (*data_empty_count - UART_BYTE_SIZE < 0)
+ break;
+ writeb(xmit->buf[xmit->tail], port->membase +
+ UART_TX_BYTE_FIFO);
+ *data_empty_count -= UART_BYTE_SIZE;
+ *valid_byte_count -= UART_BYTE_SIZE;
+
+ /*
+ * When the tail of the circular buffer is reached, the next
+ * byte is transferred to the beginning of the buffer.
+ */
+ xmit->tail = (xmit->tail + UART_BYTE_SIZE) &
+ (UART_XMIT_SIZE - 1);
+
+ /*
+ * If there are any pending burst count, data is handled by
+ * transmitting DWORDs at a time.
+ */
+ if (valid_burst_count && (xmit->tail <
+ (UART_XMIT_SIZE - UART_BURST_SIZE)))
+ break;
+ }
+}
+
+static void pci1xxxx_tx_burst(struct uart_port *port, u32 uart_status)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ u32 valid_byte_count;
+ int data_empty_count;
+ struct circ_buf *xmit;
+
+ xmit = &port->state->xmit;
+
+ if (port->x_char) {
+ writeb(port->x_char, port->membase + UART_TX);
+ port->icount.tx++;
+ port->x_char = 0;
+ return;
+ }
+
+ if ((uart_tx_stopped(port)) || (uart_circ_empty(xmit))) {
+ port->ops->stop_tx(port);
+ } else {
+ data_empty_count = (pci1xxxx_read_burst_status(port) &
+ UART_BST_STAT_TX_COUNT_MASK) >> 8;
+ do {
+ valid_byte_count = uart_circ_chars_pending(xmit);
+
+ pci1xxxx_process_write_data(port, xmit,
+ &data_empty_count,
+ &valid_byte_count);
+
+ port->icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ } while (data_empty_count && valid_byte_count);
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ /*
+ * With RPM enabled, we have to wait until the FIFO is empty before
+ * the HW can go idle. So we get here once again with empty FIFO and
+ * disable the interrupt and RPM in __stop_tx()
+ */
+ if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM))
+ port->ops->stop_tx(port);
+}
+
static int pci1xxxx_handle_irq(struct uart_port *port)
{
unsigned long flags;
@@ -359,6 +462,9 @@ static int pci1xxxx_handle_irq(struct uart_port *port)
if (status & UART_BST_STAT_LSR_RX_MASK)
pci1xxxx_rx_burst(port, status);
+ if (status & UART_BST_STAT_LSR_THRE)
+ pci1xxxx_tx_burst(port, status);
+
spin_unlock_irqrestore(&port->lock, flags);
return 1;
--
2.25.1
