On Tue, Dec 05, 2023 at 10:56:09AM +0100, Jiri Slaby wrote:
> On 30. 11. 23, 23:44, Frank Li wrote:
> > In typical embedded Linux systems, UART consoles require at least two pins,
> > TX and RX. In scenarios where I2C/I3C devices like sensors or PMICs are
> > present, we can save these two pins by using this driver. Pins is crucial
> > resources, especially in small chip packages.
> >
> > This introduces support for using the I3C bus to transfer console tty data,
> > effectively replacing the need for dedicated UART pins. This not only
> > conserves valuable pin resources but also facilitates testing of I3C's
> > advanced features, including early termination, in-band interrupt (IBI)
> > support, and the creation of more complex data patterns. Additionally,
> > it aids in identifying and addressing issues within the I3C controller
> > driver.
> >
> > Signed-off-by: Frank Li <Frank.Li@xxxxxxx>
> ...
> > --- a/drivers/tty/Kconfig
> > +++ b/drivers/tty/Kconfig
> > @@ -412,6 +412,19 @@ config RPMSG_TTY
> > To compile this driver as a module, choose M here: the module will be
> > called rpmsg_tty.
> > +config I3C_TTY
> > + tristate "TTY over I3C"
> > + depends on I3C
> > + help
> > + Select this options if you'd like use TTY over I3C master controller
>
> this option
> to use
> add a period to the end.
>
> > +
> > + This makes it possible for user-space programs to send and receive
> > + data as a standard tty protocol. I3C provide relatively higher data
> > + transfer rate and less pin numbers, SDA/SCL are shared with other
> > + devices.
> > +
> > + If unsure, say N
> > +
> > endif # TTY
> > source "drivers/tty/serdev/Kconfig"
> ...
> > --- /dev/null
> > +++ b/drivers/tty/i3c_tty.c
> > @@ -0,0 +1,443 @@
> ...
> > +struct ttyi3c_port {
> > + struct tty_port port;
> > + int minor;
> > + spinlock_t xlock; /* protect xmit */
> > + char tx_buff[I3C_TTY_TRANS_SIZE];
> > + char rx_buff[I3C_TTY_TRANS_SIZE];
>
> These should be u8 as per the other changes throughout the tty layer.
>
> > + struct i3c_device *i3cdev;
> > + struct work_struct txwork;
> > + struct work_struct rxwork;
> > + struct completion txcomplete;
> > + unsigned long status;
> > + int buf_overrun;
>
> Can this be ever negative?
>
> > +};
> > +
> > +struct workqueue_struct *workqueue;
>
> Is this related:
> Still below items not be fixed (according to Jiri Slaby's comments)
> - rxwork thread: need trigger from two position.
> - common thread queue: need some suggestion
> ?
>
> As I don't remember, could you elaborate again why you need your own
> workqueue? You need to do it in the commit log anyway.
I just learn from other drivers, such as USB ACM, usb gadget ACM driver.
If use common workqueue, which one prefered.
I will send fixed version after i3c part accepted.
Frank
>
> ...
> > +static ssize_t i3c_write(struct tty_struct *tty, const unsigned char *buf, size_t count)
> > +{
> > + struct ttyi3c_port *sport = tty->driver_data;
> > + unsigned long flags;
> > + bool is_empty;
> > + int ret;
> > +
> > + spin_lock_irqsave(&sport->xlock, flags);
> > + ret = kfifo_in(&sport->port.xmit_fifo, buf, count);
> > + is_empty = kfifo_is_empty(&sport->port.xmit_fifo);
> > + spin_unlock_irqrestore(&sport->xlock, flags);
> > +
> > + if (!is_empty)
> > + queue_work(workqueue, &sport->txwork);
> > +
> > + return ret;
> > +}
> > +
> > +static int i3c_put_char(struct tty_struct *tty, unsigned char ch)
> > +{
> > + struct ttyi3c_port *sport = tty->driver_data;
> > + unsigned long flags;
> > + int ret = 0;
>
> Unneeded initialization.
>
> > +
> > + spin_lock_irqsave(&sport->xlock, flags);
> > + ret = kfifo_put(&sport->port.xmit_fifo, ch);
> > + spin_unlock_irqrestore(&sport->xlock, flags);
> > +
> > + return ret;
> > +}
> ...
> > +static void tty_i3c_rxwork(struct work_struct *work)
> > +{
> > + struct ttyi3c_port *sport = container_of(work, struct ttyi3c_port, rxwork);
> > + struct i3c_priv_xfer xfers;
> > + int retry = I3C_TTY_RETRY;
>
> Likely, should be unsigned.
>
> > + u16 status = BIT(0);
> > + int ret;
> > +
> > + memset(&xfers, 0, sizeof(xfers));
> > + xfers.data.in = sport->rx_buff;
> > + xfers.len = I3C_TTY_TRANS_SIZE;
> > + xfers.rnw = 1;
> > +
> > + do {
> > + if (test_bit(I3C_TTY_RX_STOP, &sport->status))
> > + break;
> > +
> > + i3c_device_do_priv_xfers(sport->i3cdev, &xfers, 1);
> > +
> > + if (xfers.actual_len) {
> > + ret = tty_insert_flip_string(&sport->port, sport->rx_buff,
> > + xfers.actual_len);
> > + if (ret < xfers.actual_len)
> > + sport->buf_overrun++;
> > +
> > + retry = I3C_TTY_RETRY;
> > + continue;
> > + }
> > +
> > + status = BIT(0);
> > + i3c_device_getstatus_format1(sport->i3cdev, &status);
> > + /*
> > + * Target side needs some time to fill data into fifo. Target side may not
> > + * have hardware update status in real time. Software update status always
> > + * needs some delays.
> > + *
> > + * Generally, target side have circular buffer in memory, it will be moved
> > + * into FIFO by CPU or DMA. 'status' just show if circular buffer empty. But
> > + * there are gap, especially CPU have not response irq to fill FIFO in time.
> > + * So xfers.actual will be zero, wait for little time to avoid flood
> > + * transfer in i3c bus.
> > + */
> > + usleep_range(I3C_TTY_YIELD_US, 10 * I3C_TTY_YIELD_US);
> > + retry--;
> > +
> > + } while (retry && (status & BIT(0)));
> > +
> > + tty_flip_buffer_push(&sport->port);
> > +}
> > +
> > +static void tty_i3c_txwork(struct work_struct *work)
> > +{
> > + struct ttyi3c_port *sport = container_of(work, struct ttyi3c_port, txwork);
> > + struct i3c_priv_xfer xfers;
> > + int retry = I3C_TTY_RETRY;
>
> Detto.
>
> > + unsigned long flags;
> > + int ret;
> > +
> > + xfers.rnw = 0;
> > + xfers.data.out = sport->tx_buff;
> > +
> > + while (!kfifo_is_empty(&sport->port.xmit_fifo) && retry) {
> > + xfers.len = kfifo_len(&sport->port.xmit_fifo);
> > + xfers.len = min_t(u16, I3C_TTY_TRANS_SIZE, xfers.len);
> > +
> > + xfers.len = kfifo_out_peek(&sport->port.xmit_fifo, sport->tx_buff, xfers.len);
>
> Can this simply be:
> xfers.len = kfifo_out_peek(&sport->port.xmit_fifo, sport->tx_buff,
> I3C_TTY_TRANS_SIZE);
> ?
>
> > +
> > + ret = i3c_device_do_priv_xfers(sport->i3cdev, &xfers, 1);
> > + if (ret) {
> > + /*
> > + * Target side may not move data out of FIFO. delay can't resolve problem,
> > + * just reduce some possiblity. Target can't end I3C SDR mode write
> > + * transfer, discard data is reasonable when FIFO overrun.
> > + */
> > + usleep_range(I3C_TTY_YIELD_US, 10 * I3C_TTY_YIELD_US);
> > + retry--;
> > + } else {
> > + retry = I3C_TTY_RETRY;
> > + ret = kfifo_out(&sport->port.xmit_fifo, sport->tx_buff, xfers.len);
>
> Just to make sure: xfers.len is nor overwritten by
> i3c_device_do_priv_xfers(), right?
>
> > + }
> > + }
> > +
> > + spin_lock_irqsave(&sport->xlock, flags);
>
> Why do you take the lock here, but not during the kfifo operations above?
>
> > + if (kfifo_is_empty(&sport->port.xmit_fifo))
> > + complete(&sport->txcomplete);
> > + spin_unlock_irqrestore(&sport->xlock, flags);
> > +}
>
> > +static int __init i3c_tty_init(void)
> > +{
> > + int ret;
> > +
> > + i3c_tty_driver = tty_alloc_driver(I3C_TTY_MINORS,
> > + TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV);
> > +
> > + if (IS_ERR(i3c_tty_driver))
> > + return PTR_ERR(i3c_tty_driver);
> > +
> > + i3c_tty_driver->driver_name = "ttyI3C";
> > + i3c_tty_driver->name = "ttyI3C";
> > + i3c_tty_driver->minor_start = 0,
> > + i3c_tty_driver->type = TTY_DRIVER_TYPE_SERIAL,
> > + i3c_tty_driver->subtype = SERIAL_TYPE_NORMAL,
> > + i3c_tty_driver->init_termios = tty_std_termios;
> > + i3c_tty_driver->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL |
> > + CLOCAL;
> > + i3c_tty_driver->init_termios.c_lflag = 0;
> > +
> > + tty_set_operations(i3c_tty_driver, &i3c_tty_ops);
> > +
> > + ret = tty_register_driver(i3c_tty_driver);
> > + if (ret)
> > + goto err_tty_register_driver;
> > +
> > + ret = i3c_driver_register(&i3c_driver);
> > + if (ret)
> > + goto err_i3c_driver_register;
> > +
> > + workqueue = alloc_workqueue("ttyI3C", 0, 0);
>
> Can it happen that you already queue something on this wq, while not
> allocated yet? I mean: should this be done first in i3c_tty_init()?
>
> > + if (!workqueue) {
> > + ret = PTR_ERR(workqueue);
> > + goto err_alloc_workqueue;
> > + }
> > +
> > + return 0;
> > +
> > +err_alloc_workqueue:
> > + i3c_driver_unregister(&i3c_driver);
> > +
> > +err_i3c_driver_register:
> > + tty_unregister_driver(i3c_tty_driver);
> > +
> > +err_tty_register_driver:
> > + tty_driver_kref_put(i3c_tty_driver);
> > +
> > + return ret;
> > +}
> > +
> > +static void __exit i3c_tty_exit(void)
> > +{
> > + i3c_driver_unregister(&i3c_driver);
> > + tty_unregister_driver(i3c_tty_driver);
> > + tty_driver_kref_put(i3c_tty_driver);
> > + idr_destroy(&i3c_tty_minors);
>
> What about the wq?
>
> > +}
>
> regards,
> --
> js
> suse labs
>
