On Wed, 22 Nov 2023, Gregory CLEMENT wrote: > From: Arnd Bergmann <arnd@xxxxxxxx> > > Since there is no guarantee that the memory returned by > dma_alloc_coherent() is associated with a 'struct page', using the > architecture specific phys_to_page() is wrong, but using > virt_to_page() would be as well. > > Stop using sg lists altogether and just use the *_single() functions > instead. This also simplifies the code a bit since the scatterlists in > this driver always have only one entry anyway. Is that actually a HW limitation? Because it would be nice to get rid of those memcpy()s and use sg with two entries which is the general direction serial doing DMA Tx should be moving towards (IMO). -- i. > gcl: Add a commit log from the initial thread: > https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@xxxxxxxxxxxxxxxx/ > > Fixes: cb06ff102e2d7 ("ARM: PL011: Add support for Rx DMA buffer polling.") > Signed-off-by: Arnd Bergmann <arnd@xxxxxxxx> > Tested-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxx> > Signed-off-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxx> > --- > drivers/tty/serial/amba-pl011.c | 62 +++++++++++++++------------------ > 1 file changed, 29 insertions(+), 33 deletions(-) > > diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c > index 61cc24cd90e4b..73a1c40148c25 100644 > --- a/drivers/tty/serial/amba-pl011.c > +++ b/drivers/tty/serial/amba-pl011.c > @@ -219,8 +219,9 @@ static struct vendor_data vendor_st = { > /* Deals with DMA transactions */ > > struct pl011_sgbuf { > - struct scatterlist sg; > - char *buf; > + dma_addr_t dma; > + size_t len; > + char *buf; > }; > > struct pl011_dmarx_data { > @@ -241,7 +242,8 @@ struct pl011_dmarx_data { > > struct pl011_dmatx_data { > struct dma_chan *chan; > - struct scatterlist sg; > + dma_addr_t dma; > + size_t len; > char *buf; > bool queued; > }; > @@ -369,18 +371,11 @@ static int pl011_fifo_to_tty(struct uart_amba_port *uap) > static int pl011_sgbuf_init(struct dma_chan *chan, struct pl011_sgbuf *sg, > enum dma_data_direction dir) > { > - dma_addr_t dma_addr; > - > - sg->buf = dma_alloc_coherent(chan->device->dev, > - PL011_DMA_BUFFER_SIZE, &dma_addr, GFP_KERNEL); > + sg->buf = dma_alloc_coherent(chan->device->dev, PL011_DMA_BUFFER_SIZE, > + &sg->dma, GFP_KERNEL); > if (!sg->buf) > return -ENOMEM; > - > - sg_init_table(&sg->sg, 1); > - sg_set_page(&sg->sg, phys_to_page(dma_addr), > - PL011_DMA_BUFFER_SIZE, offset_in_page(dma_addr)); > - sg_dma_address(&sg->sg) = dma_addr; > - sg_dma_len(&sg->sg) = PL011_DMA_BUFFER_SIZE; > + sg->len = PL011_DMA_BUFFER_SIZE; > > return 0; > } > @@ -390,8 +385,7 @@ static void pl011_sgbuf_free(struct dma_chan *chan, struct pl011_sgbuf *sg, > { > if (sg->buf) { > dma_free_coherent(chan->device->dev, > - PL011_DMA_BUFFER_SIZE, sg->buf, > - sg_dma_address(&sg->sg)); > + PL011_DMA_BUFFER_SIZE, sg->buf, sg->dma); > } > } > > @@ -552,8 +546,8 @@ static void pl011_dma_tx_callback(void *data) > > uart_port_lock_irqsave(&uap->port, &flags); > if (uap->dmatx.queued) > - dma_unmap_sg(dmatx->chan->device->dev, &dmatx->sg, 1, > - DMA_TO_DEVICE); > + dma_unmap_single(dmatx->chan->device->dev, dmatx->dma, > + dmatx->len, DMA_TO_DEVICE); > > dmacr = uap->dmacr; > uap->dmacr = dmacr & ~UART011_TXDMAE; > @@ -639,18 +633,19 @@ static int pl011_dma_tx_refill(struct uart_amba_port *uap) > memcpy(&dmatx->buf[first], &xmit->buf[0], second); > } > > - dmatx->sg.length = count; > - > - if (dma_map_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE) != 1) { > + dmatx->len = count; > + dmatx->dma = dma_map_single(dma_dev->dev, dmatx->buf, count, > + DMA_TO_DEVICE); > + if (dmatx->dma == DMA_MAPPING_ERROR) { > uap->dmatx.queued = false; > dev_dbg(uap->port.dev, "unable to map TX DMA\n"); > return -EBUSY; > } > > - desc = dmaengine_prep_slave_sg(chan, &dmatx->sg, 1, DMA_MEM_TO_DEV, > + desc = dmaengine_prep_slave_single(chan, dmatx->dma, dmatx->len, DMA_MEM_TO_DEV, > DMA_PREP_INTERRUPT | DMA_CTRL_ACK); > if (!desc) { > - dma_unmap_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE); > + dma_unmap_single(dma_dev->dev, dmatx->dma, dmatx->len, DMA_TO_DEVICE); > uap->dmatx.queued = false; > /* > * If DMA cannot be used right now, we complete this > @@ -813,8 +808,8 @@ __acquires(&uap->port.lock) > dmaengine_terminate_async(uap->dmatx.chan); > > if (uap->dmatx.queued) { > - dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1, > - DMA_TO_DEVICE); > + dma_unmap_single(uap->dmatx.chan->device->dev, uap->dmatx.dma, > + uap->dmatx.len, DMA_TO_DEVICE); > uap->dmatx.queued = false; > uap->dmacr &= ~UART011_TXDMAE; > pl011_write(uap->dmacr, uap, REG_DMACR); > @@ -836,7 +831,7 @@ static int pl011_dma_rx_trigger_dma(struct uart_amba_port *uap) > /* Start the RX DMA job */ > sgbuf = uap->dmarx.use_buf_b ? > &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a; > - desc = dmaengine_prep_slave_sg(rxchan, &sgbuf->sg, 1, > + desc = dmaengine_prep_slave_single(rxchan, sgbuf->dma, sgbuf->len, > DMA_DEV_TO_MEM, > DMA_PREP_INTERRUPT | DMA_CTRL_ACK); > /* > @@ -886,7 +881,7 @@ static void pl011_dma_rx_chars(struct uart_amba_port *uap, > > if (uap->dmarx.poll_rate) { > /* The data can be taken by polling */ > - dmataken = sgbuf->sg.length - dmarx->last_residue; > + dmataken = sgbuf->len - dmarx->last_residue; > /* Recalculate the pending size */ > if (pending >= dmataken) > pending -= dmataken; > @@ -911,7 +906,7 @@ static void pl011_dma_rx_chars(struct uart_amba_port *uap, > > /* Reset the last_residue for Rx DMA poll */ > if (uap->dmarx.poll_rate) > - dmarx->last_residue = sgbuf->sg.length; > + dmarx->last_residue = sgbuf->len; > > /* > * Only continue with trying to read the FIFO if all DMA chars have > @@ -969,7 +964,7 @@ static void pl011_dma_rx_irq(struct uart_amba_port *uap) > pl011_write(uap->dmacr, uap, REG_DMACR); > uap->dmarx.running = false; > > - pending = sgbuf->sg.length - state.residue; > + pending = sgbuf->len - state.residue; > BUG_ON(pending > PL011_DMA_BUFFER_SIZE); > /* Then we terminate the transfer - we now know our residue */ > dmaengine_terminate_all(rxchan); > @@ -1015,7 +1010,7 @@ static void pl011_dma_rx_callback(void *data) > * the DMA irq handler. So we check the residue here. > */ > rxchan->device->device_tx_status(rxchan, dmarx->cookie, &state); > - pending = sgbuf->sg.length - state.residue; > + pending = sgbuf->len - state.residue; > BUG_ON(pending > PL011_DMA_BUFFER_SIZE); > /* Then we terminate the transfer - we now know our residue */ > dmaengine_terminate_all(rxchan); > @@ -1074,7 +1069,7 @@ static void pl011_dma_rx_poll(struct timer_list *t) > sgbuf = dmarx->use_buf_b ? &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a; > rxchan->device->device_tx_status(rxchan, dmarx->cookie, &state); > if (likely(state.residue < dmarx->last_residue)) { > - dmataken = sgbuf->sg.length - dmarx->last_residue; > + dmataken = sgbuf->len - dmarx->last_residue; > size = dmarx->last_residue - state.residue; > dma_count = tty_insert_flip_string(port, sgbuf->buf + dmataken, > size); > @@ -1123,7 +1118,7 @@ static void pl011_dma_startup(struct uart_amba_port *uap) > return; > } > > - sg_init_one(&uap->dmatx.sg, uap->dmatx.buf, PL011_DMA_BUFFER_SIZE); > + uap->dmatx.len = PL011_DMA_BUFFER_SIZE; > > /* The DMA buffer is now the FIFO the TTY subsystem can use */ > uap->port.fifosize = PL011_DMA_BUFFER_SIZE; > @@ -1200,8 +1195,9 @@ static void pl011_dma_shutdown(struct uart_amba_port *uap) > /* In theory, this should already be done by pl011_dma_flush_buffer */ > dmaengine_terminate_all(uap->dmatx.chan); > if (uap->dmatx.queued) { > - dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1, > - DMA_TO_DEVICE); > + dma_unmap_single(uap->dmatx.chan->device->dev, > + uap->dmatx.dma, uap->dmatx.len, > + DMA_TO_DEVICE); > uap->dmatx.queued = false; > } > >
