On 18. 10. 23, 11:17, Crescent CY Hsieh wrote:
MOXA PCIe RS422/RS485 boards will not function by default because of the
initial default serial interface of all MOXA PCIe boards is set to RS232.
This patch fixes the problem above by setting the initial default serial
interface to RS422 for those MOXA RS422/RS485 PCIe boards.
Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@xxxxxxxx>
---
drivers/tty/serial/8250/8250_pci.c | 52 ++++++++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index b2be3783f..29a28e72b 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
...
@@ -1981,13 +1987,59 @@ static bool pci_moxa_is_mini_pcie(unsigned short device)
return false;
}
+/*
+ * The second digit of the MOXA PCIe device ID in hexadecimal indicates
+ * which serial interface modes this board supports:
+ *
+ * 0x*0** - RS232
+ * 0x*1** - RS232/RS422/RS485
+ * 0x*3** - RS422/RS485
+ * 0x*6** - RS232
+ */
+static bool pci_moxa_match_second_digit(unsigned short device,
+ unsigned short pattern)
+{
+ return (device & 0x0F00) == pattern;
+}
Actually, would it make sense to define the below instead:
enum {
MOXA_SUPP_RS232 = BIT(0),
MOXA_SUPP_RS422 = BIT(1),
MOXA_SUPP_RS485 = BIT(2),
};
u32 pci_moxa_supported_rs(struct pci_dev *dev)
{
switch (dev->device & 0x0f00) {
case 0x0000:
case 0x0600: // or default: ???
return MOXA_SUPP_RS232;
case 0x0100:
return MOXA_SUPP_RS232 | MOXA_SUPP_RS422 | MOXA_SUPP_RS485;
case 0x0300:
return MOXA_SUPP_RS422 | MOXA_SUPP_RS485;
}
return 0;
}
...
static int pci_moxa_init(struct pci_dev *dev)
{
unsigned short device = dev->device;
resource_size_t iobar_addr = pci_resource_start(dev, 2);
+ unsigned int i;
unsigned int num_ports = (device & 0x00F0) >> 4;
u8 val;
+ /*
+ * For the device IDs of MOXA PCIe boards match the pattern 0x*3**,
+ * the initial default serial interface mode should be set to RS422.
+ */
+ if (pci_moxa_match_second_digit(device, 0x0300)) {
And here:
if (pci_moxa_supported_rs(dev) == MOXA_SUPP_RS422 | MOXA_SUPP_RS485)
or perhaps:
if (!(pci_moxa_supported_rs(dev) & MOXA_SUPP_RS232))
?
+ for (i = 0; i < num_ports; ++i)
+ pci_moxa_set_interface(dev, i, MOXA_RS422);
+ }
/*
* Enable hardware buffer to prevent break signal output when system boots up.
* This hardware buffer is only supported on Mini PCIe series.
--
js
suse labs