Re: [PATCH 4/4] drivers/tty/serial: add ESP32S3 ACM device driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, 13 Sep 2023, Max Filippov wrote:

> Add driver for the ACM  controller of the Espressif ESP32S3 Soc.
> Hardware specification is available at the following URL:
> 
>   https://www.espressif.com/sites/default/files/documentation/esp32-s3_technical_reference_manual_en.pdf
>   (Chapter 33 USB Serial/JTAG Controller)
> 
> Signed-off-by: Max Filippov <jcmvbkbc@xxxxxxxxx>
> ---
>  drivers/tty/serial/Kconfig       |  14 +
>  drivers/tty/serial/Makefile      |   1 +
>  drivers/tty/serial/esp32_acm.c   | 473 +++++++++++++++++++++++++++++++
>  include/uapi/linux/serial_core.h |   3 +
>  4 files changed, 491 insertions(+)
>  create mode 100644 drivers/tty/serial/esp32_acm.c

Please go through this with the comments against the other patch in mind, 
I don't want to spend my time on reviewing it yet just to mark all the 
similar issues.

-- 
 i.

> 
> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> index d9ca6b268f01..85807db8f7ce 100644
> --- a/drivers/tty/serial/Kconfig
> +++ b/drivers/tty/serial/Kconfig
> @@ -1591,6 +1591,20 @@ config SERIAL_ESP32
>  	    earlycon=esp32s3uart,mmio32,0x60000000,115200n8,40000000
>  	    earlycon=esp32uart,mmio32,0x3ff40000,115200n8
>  
> +config SERIAL_ESP32_ACM
> +	tristate "Espressif ESP32 USB ACM support"
> +	depends on XTENSA_PLATFORM_ESP32 || (COMPILE_TEST && OF)
> +	select SERIAL_CORE
> +	select SERIAL_CORE_CONSOLE
> +	select SERIAL_EARLYCON
> +	help
> +	  Driver for the CDC ACM controllers of the Espressif ESP32S3 SoCs
> +	  that share separate USB controller with the JTAG adapter.
> +	  The device name used for this controller is ttyACM.
> +	  When earlycon option is enabled the following kernel command line
> +	  snippet may be used:
> +	    earlycon=esp32s3acm,mmio32,0x60038000
> +
>  endmenu
>  
>  config SERIAL_MCTRL_GPIO
> diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
> index 7b73137df7f3..970a292ca418 100644
> --- a/drivers/tty/serial/Makefile
> +++ b/drivers/tty/serial/Makefile
> @@ -89,6 +89,7 @@ obj-$(CONFIG_SERIAL_SIFIVE)	+= sifive.o
>  obj-$(CONFIG_SERIAL_LITEUART) += liteuart.o
>  obj-$(CONFIG_SERIAL_SUNPLUS)	+= sunplus-uart.o
>  obj-$(CONFIG_SERIAL_ESP32)	+= esp32_uart.o
> +obj-$(CONFIG_SERIAL_ESP32_ACM)	+= esp32_acm.o
>  
>  # GPIOLIB helpers for modem control lines
>  obj-$(CONFIG_SERIAL_MCTRL_GPIO)	+= serial_mctrl_gpio.o
> diff --git a/drivers/tty/serial/esp32_acm.c b/drivers/tty/serial/esp32_acm.c
> new file mode 100644
> index 000000000000..f178e6af93f3
> --- /dev/null
> +++ b/drivers/tty/serial/esp32_acm.c
> @@ -0,0 +1,473 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +
> +#include <linux/console.h>
> +#include <linux/io.h>
> +#include <linux/irq.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/serial_core.h>
> +#include <linux/slab.h>
> +#include <linux/tty_flip.h>
> +#include <linux/delay.h>
> +#include <asm/serial.h>
> +
> +#define DRIVER_NAME	"esp32s3-acm"
> +#define DEV_NAME	"ttyACM"
> +#define UART_NR		4
> +
> +#define ESP32S3_ACM_TX_FIFO_SIZE	64
> +
> +#define USB_SERIAL_JTAG_EP1_REG		0x00
> +#define USB_SERIAL_JTAG_EP1_CONF_REG	0x04
> +#define USB_SERIAL_JTAG_WR_DONE_MASK				0x00000001
> +#define USB_SERIAL_JTAG_SERIAL_IN_EP_DATA_FREE_MASK		0x00000002
> +#define USB_SERIAL_JTAG_SERIAL_OUT_EP_DATA_AVAIL_MASK		0x00000008
> +#define USB_SERIAL_JTAG_INT_ST_REG	0x0c
> +#define USB_SERIAL_JTAG_SERIAL_OUT_RECV_PKT_INT_ST_MASK		0x00000004
> +#define USB_SERIAL_JTAG_SERIAL_IN_EMPTY_INT_ST_MASK		0x00000008
> +#define USB_SERIAL_JTAG_INT_ENA_REG	0x10
> +#define USB_SERIAL_JTAG_SERIAL_OUT_RECV_PKT_INT_ENA_MASK	0x00000004
> +#define USB_SERIAL_JTAG_SERIAL_IN_EMPTY_INT_ENA_MASK		0x00000008
> +#define USB_SERIAL_JTAG_INT_CLR_REG	0x14
> +#define USB_SERIAL_JTAG_IN_EP1_ST_REG	0x2c
> +#define USB_SERIAL_JTAG_IN_EP1_WR_ADDR_MASK			0x000001fc
> +#define USB_SERIAL_JTAG_IN_EP1_WR_ADDR_SHIFT			2
> +#define USB_SERIAL_JTAG_OUT_EP1_ST_REG	0x3c
> +#define USB_SERIAL_JTAG_OUT_EP1_REC_DATA_CNT_MASK		0x007f0000
> +#define USB_SERIAL_JTAG_OUT_EP1_REC_DATA_CNT_SHIFT		16
> +
> +static const struct of_device_id esp32s3_acm_dt_ids[] = {
> +	{
> +		.compatible = "esp,esp32s3-acm",
> +	}, { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, esp32s3_acm_dt_ids);
> +
> +static struct uart_port *esp32s3_acm_ports[UART_NR];
> +
> +static void esp32s3_acm_write(struct uart_port *port, unsigned long reg, u32 v)
> +{
> +	writel(v, port->membase + reg);
> +}
> +
> +static u32 esp32s3_acm_read(struct uart_port *port, unsigned long reg)
> +{
> +	return readl(port->membase + reg);
> +}
> +
> +static u32 esp32s3_acm_tx_fifo_free(struct uart_port *port)
> +{
> +	return esp32s3_acm_read(port, USB_SERIAL_JTAG_EP1_CONF_REG) &
> +		USB_SERIAL_JTAG_SERIAL_IN_EP_DATA_FREE_MASK;
> +}
> +
> +static u32 esp32s3_acm_tx_fifo_cnt(struct uart_port *port)
> +{
> +	u32 status = esp32s3_acm_read(port, USB_SERIAL_JTAG_IN_EP1_ST_REG);
> +
> +	return (status & USB_SERIAL_JTAG_IN_EP1_WR_ADDR_MASK) >>
> +		USB_SERIAL_JTAG_IN_EP1_WR_ADDR_SHIFT;
> +}
> +
> +static u32 esp32s3_acm_rx_fifo_cnt(struct uart_port *port)
> +{
> +	u32 status = esp32s3_acm_read(port, USB_SERIAL_JTAG_OUT_EP1_ST_REG);
> +
> +	return (status & USB_SERIAL_JTAG_OUT_EP1_REC_DATA_CNT_MASK) >>
> +		USB_SERIAL_JTAG_OUT_EP1_REC_DATA_CNT_SHIFT;
> +}
> +
> +/* return TIOCSER_TEMT when transmitter is not busy */
> +static unsigned int esp32s3_acm_tx_empty(struct uart_port *port)
> +{
> +	return esp32s3_acm_tx_fifo_cnt(port) == 0 ? TIOCSER_TEMT : 0;
> +}
> +
> +static void esp32s3_acm_set_mctrl(struct uart_port *port, unsigned int mctrl)
> +{
> +}
> +
> +static unsigned int esp32s3_acm_get_mctrl(struct uart_port *port)
> +{
> +	return TIOCM_CAR;
> +}
> +
> +static void esp32s3_acm_stop_tx(struct uart_port *port)
> +{
> +	u32 int_ena;
> +
> +	int_ena = esp32s3_acm_read(port, USB_SERIAL_JTAG_INT_ENA_REG);
> +	esp32s3_acm_write(port, USB_SERIAL_JTAG_INT_ENA_REG,
> +			  int_ena & ~USB_SERIAL_JTAG_SERIAL_IN_EMPTY_INT_ENA_MASK);
> +}
> +
> +static void esp32s3_acm_rxint(struct uart_port *port)
> +{
> +	struct tty_port *tty_port = &port->state->port;
> +	u32 rx_fifo_cnt = esp32s3_acm_rx_fifo_cnt(port);
> +	unsigned long flags;
> +	u32 i;
> +
> +	if (!rx_fifo_cnt)
> +		return;
> +
> +	spin_lock_irqsave(&port->lock, flags);
> +
> +	for (i = 0; i < rx_fifo_cnt; ++i) {
> +		u32 rx = esp32s3_acm_read(port, USB_SERIAL_JTAG_EP1_REG);
> +
> +		++port->icount.rx;
> +		tty_insert_flip_char(tty_port, rx, TTY_NORMAL);
> +	}
> +	spin_unlock_irqrestore(&port->lock, flags);
> +
> +	tty_flip_buffer_push(tty_port);
> +}
> +
> +static void esp32s3_acm_push(struct uart_port *port)
> +{
> +	if (esp32s3_acm_tx_fifo_free(port))
> +		esp32s3_acm_write(port, USB_SERIAL_JTAG_EP1_CONF_REG,
> +				  USB_SERIAL_JTAG_WR_DONE_MASK);
> +}
> +
> +static void esp32s3_acm_put_char(struct uart_port *port, unsigned char c)
> +{
> +	esp32s3_acm_write(port, USB_SERIAL_JTAG_EP1_REG, c);
> +}
> +
> +static void esp32s3_acm_put_char_sync(struct uart_port *port, unsigned char c)
> +{
> +	while (!esp32s3_acm_tx_fifo_free(port))
> +		cpu_relax();
> +	esp32s3_acm_put_char(port, c);
> +	esp32s3_acm_push(port);
> +}
> +
> +static void esp32s3_acm_transmit_buffer(struct uart_port *port)
> +{
> +	struct circ_buf *xmit = &port->state->xmit;
> +	u32 tx_fifo_used = esp32s3_acm_tx_fifo_cnt(port);
> +
> +	if (esp32s3_acm_tx_fifo_free(port)) {
> +		while (!uart_circ_empty(xmit) && tx_fifo_used < ESP32S3_ACM_TX_FIFO_SIZE) {
> +			esp32s3_acm_put_char(port, xmit->buf[xmit->tail]);
> +			xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
> +			port->icount.tx++;
> +			++tx_fifo_used;
> +		}
> +	}
> +
> +	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
> +		uart_write_wakeup(port);
> +
> +	if (uart_circ_empty(xmit)) {
> +		esp32s3_acm_stop_tx(port);
> +	} else {
> +		u32 int_ena;
> +
> +		int_ena = esp32s3_acm_read(port, USB_SERIAL_JTAG_INT_ENA_REG);
> +		esp32s3_acm_write(port, USB_SERIAL_JTAG_INT_ENA_REG,
> +				  int_ena | USB_SERIAL_JTAG_SERIAL_IN_EMPTY_INT_ENA_MASK);
> +	}
> +
> +	if (tx_fifo_used > 0 && tx_fifo_used < ESP32S3_ACM_TX_FIFO_SIZE)
> +		esp32s3_acm_write(port, USB_SERIAL_JTAG_EP1_CONF_REG,
> +				  USB_SERIAL_JTAG_WR_DONE_MASK);
> +}
> +
> +static void esp32s3_acm_txint(struct uart_port *port)
> +{
> +	esp32s3_acm_transmit_buffer(port);
> +}
> +
> +static irqreturn_t esp32s3_acm_int(int irq, void *dev_id)
> +{
> +	struct uart_port *port = dev_id;
> +	u32 status;
> +
> +	status = esp32s3_acm_read(port, USB_SERIAL_JTAG_INT_ST_REG);
> +	esp32s3_acm_write(port, USB_SERIAL_JTAG_INT_CLR_REG, status);
> +
> +	if (status & USB_SERIAL_JTAG_SERIAL_OUT_RECV_PKT_INT_ST_MASK)
> +		esp32s3_acm_rxint(port);
> +	if (status & USB_SERIAL_JTAG_SERIAL_IN_EMPTY_INT_ST_MASK)
> +		esp32s3_acm_txint(port);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static void esp32s3_acm_start_tx(struct uart_port *port)
> +{
> +	esp32s3_acm_transmit_buffer(port);
> +}
> +
> +static void esp32s3_acm_stop_rx(struct uart_port *port)
> +{
> +	u32 int_ena;
> +
> +	int_ena = esp32s3_acm_read(port, USB_SERIAL_JTAG_INT_ENA_REG);
> +	esp32s3_acm_write(port, USB_SERIAL_JTAG_INT_ENA_REG,
> +			  int_ena & ~USB_SERIAL_JTAG_SERIAL_OUT_RECV_PKT_INT_ENA_MASK);
> +}
> +
> +static int esp32s3_acm_startup(struct uart_port *port)
> +{
> +	int ret = 0;
> +
> +	esp32s3_acm_write(port, USB_SERIAL_JTAG_INT_ENA_REG,
> +			  USB_SERIAL_JTAG_SERIAL_OUT_RECV_PKT_INT_ENA_MASK);
> +	ret = devm_request_irq(port->dev, port->irq, esp32s3_acm_int, 0,
> +			       DRIVER_NAME, port);
> +	return ret;
> +}
> +
> +static void esp32s3_acm_shutdown(struct uart_port *port)
> +{
> +	esp32s3_acm_write(port, USB_SERIAL_JTAG_INT_ENA_REG, 0);
> +	devm_free_irq(port->dev, port->irq, port);
> +}
> +
> +static void esp32s3_acm_set_termios(struct uart_port *port,
> +				    struct ktermios *termios,
> +				    const struct ktermios *old)
> +{
> +}
> +
> +static const char *esp32s3_acm_type(struct uart_port *port)
> +{
> +	return "ESP32S3 ACM";
> +}
> +
> +/* configure/auto-configure the port */
> +static void esp32s3_acm_config_port(struct uart_port *port, int flags)
> +{
> +	if (flags & UART_CONFIG_TYPE)
> +		port->type = PORT_ESP32ACM;
> +}
> +
> +#ifdef CONFIG_CONSOLE_POLL
> +static void esp32s3_acm_poll_put_char(struct uart_port *port, unsigned char c)
> +{
> +	esp32s3_acm_put_char_sync(port, c);
> +}
> +
> +static int esp32s3_acm_poll_get_char(struct uart_port *port)
> +{
> +	if (esp32s3_acm_rx_fifo_cnt(port))
> +		return esp32s3_acm_read(port, USB_SERIAL_JTAG_EP1_REG);
> +	else
> +		return NO_POLL_CHAR;
> +
> +}
> +#endif
> +
> +static const struct uart_ops esp32s3_acm_pops = {
> +	.tx_empty	= esp32s3_acm_tx_empty,
> +	.set_mctrl	= esp32s3_acm_set_mctrl,
> +	.get_mctrl	= esp32s3_acm_get_mctrl,
> +	.stop_tx	= esp32s3_acm_stop_tx,
> +	.start_tx	= esp32s3_acm_start_tx,
> +	.stop_rx	= esp32s3_acm_stop_rx,
> +	.startup	= esp32s3_acm_startup,
> +	.shutdown	= esp32s3_acm_shutdown,
> +	.set_termios	= esp32s3_acm_set_termios,
> +	.type		= esp32s3_acm_type,
> +	.config_port	= esp32s3_acm_config_port,
> +#ifdef CONFIG_CONSOLE_POLL
> +	.poll_put_char	= esp32s3_acm_poll_put_char,
> +	.poll_get_char	= esp32s3_acm_poll_get_char,
> +#endif
> +};
> +
> +static void esp32s3_acm_console_putchar(struct uart_port *port, unsigned char c)
> +{
> +	esp32s3_acm_put_char_sync(port, c);
> +}
> +
> +static void esp32s3_acm_string_write(struct uart_port *port, const char *s,
> +				     unsigned int count)
> +{
> +	uart_console_write(port, s, count, esp32s3_acm_console_putchar);
> +}
> +
> +static void
> +esp32s3_acm_console_write(struct console *co, const char *s, unsigned int count)
> +{
> +	struct uart_port *port = esp32s3_acm_ports[co->index];
> +	unsigned long flags;
> +	int locked = 1;
> +
> +	if (port->sysrq)
> +		locked = 0;
> +	else if (oops_in_progress)
> +		locked = spin_trylock_irqsave(&port->lock, flags);
> +	else
> +		spin_lock_irqsave(&port->lock, flags);
> +
> +	esp32s3_acm_string_write(port, s, count);
> +
> +	if (locked)
> +		spin_unlock_irqrestore(&port->lock, flags);
> +}
> +
> +static struct uart_driver esp32s3_acm_reg;
> +static struct console esp32s3_acm_console = {
> +	.name		= DEV_NAME,
> +	.write		= esp32s3_acm_console_write,
> +	.device		= uart_console_device,
> +	.flags		= CON_PRINTBUFFER,
> +	.index		= -1,
> +	.data		= &esp32s3_acm_reg,
> +};
> +
> +static void esp32s3_acm_earlycon_putchar(struct uart_port *port, unsigned char c)
> +{
> +	esp32s3_acm_put_char_sync(port, c);
> +}
> +
> +static void esp32s3_acm_earlycon_write(struct console *con, const char *s,
> +				      unsigned int n)
> +{
> +	struct earlycon_device *dev = con->data;
> +
> +	uart_console_write(&dev->port, s, n, esp32s3_acm_earlycon_putchar);
> +}
> +
> +#ifdef CONFIG_CONSOLE_POLL
> +static int esp32s3_acm_earlycon_read(struct console *con, char *s, unsigned int n)
> +{
> +	struct earlycon_device *dev = con->data;
> +	int num_read = 0;
> +
> +	while (num_read < n) {
> +		int c = esp32s3_acm_poll_get_char(&dev->port);
> +
> +		if (c == NO_POLL_CHAR)
> +			break;
> +		s[num_read++] = c;
> +	}
> +	return num_read;
> +}
> +#endif
> +
> +static int __init esp32s3_acm_early_console_setup(struct earlycon_device *device,
> +						   const char *options)
> +{
> +	if (!device->port.membase)
> +		return -ENODEV;
> +
> +	device->con->write = esp32s3_acm_earlycon_write;
> +#ifdef CONFIG_CONSOLE_POLL
> +	device->con->read = esp32s3_acm_earlycon_read;
> +#endif
> +	return 0;
> +}
> +
> +OF_EARLYCON_DECLARE(esp32s3acm, "esp,esp32s3-acm",
> +		    esp32s3_acm_early_console_setup);
> +
> +static struct uart_driver esp32s3_acm_reg = {
> +	.owner		= THIS_MODULE,
> +	.driver_name	= DRIVER_NAME,
> +	.dev_name	= DEV_NAME,
> +	.nr		= ARRAY_SIZE(esp32s3_acm_ports),
> +	.cons		= &esp32s3_acm_console,
> +};
> +
> +static int esp32s3_acm_probe(struct platform_device *pdev)
> +{
> +	struct device_node *np = pdev->dev.of_node;
> +	struct uart_port *port;
> +	struct resource *res;
> +	int ret;
> +
> +	port = devm_kzalloc(&pdev->dev, sizeof(*port), GFP_KERNEL);
> +	if (!port)
> +		return -ENOMEM;
> +
> +	ret = of_alias_get_id(np, "serial");
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
> +		return ret;
> +	}
> +	if (ret >= UART_NR) {
> +		dev_err(&pdev->dev, "driver limited to %d serial ports\n",
> +			UART_NR);
> +		return -ENOMEM;
> +	}
> +
> +	port->line = ret;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	if (!res)
> +		return -ENODEV;
> +
> +	port->mapbase = res->start;
> +	port->membase = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(port->membase))
> +		return PTR_ERR(port->membase);
> +
> +	port->dev = &pdev->dev;
> +	port->type = PORT_ESP32ACM;
> +	port->iotype = UPIO_MEM;
> +	port->irq = platform_get_irq(pdev, 0);
> +	port->ops = &esp32s3_acm_pops;
> +	port->flags = UPF_BOOT_AUTOCONF;
> +	port->has_sysrq = 1;
> +	port->fifosize = ESP32S3_ACM_TX_FIFO_SIZE;
> +
> +	esp32s3_acm_ports[port->line] = port;
> +
> +	platform_set_drvdata(pdev, port);
> +
> +	ret = uart_add_one_port(&esp32s3_acm_reg, port);
> +	return ret;
> +}
> +
> +static int esp32s3_acm_remove(struct platform_device *pdev)
> +{
> +	struct uart_port *port = platform_get_drvdata(pdev);
> +
> +	uart_remove_one_port(&esp32s3_acm_reg, port);
> +	return 0;
> +}
> +
> +
> +static struct platform_driver esp32s3_acm_driver = {
> +	.probe		= esp32s3_acm_probe,
> +	.remove		= esp32s3_acm_remove,
> +	.driver		= {
> +		.name	= DRIVER_NAME,
> +		.of_match_table	= esp32s3_acm_dt_ids,
> +	},
> +};
> +
> +static int __init esp32s3_acm_init(void)
> +{
> +	int ret;
> +
> +	ret = uart_register_driver(&esp32s3_acm_reg);
> +	if (ret)
> +		return ret;
> +
> +	ret = platform_driver_register(&esp32s3_acm_driver);
> +	if (ret)
> +		uart_unregister_driver(&esp32s3_acm_reg);
> +
> +	return ret;
> +}
> +
> +static void __exit esp32s3_acm_exit(void)
> +{
> +	platform_driver_unregister(&esp32s3_acm_driver);
> +	uart_unregister_driver(&esp32s3_acm_reg);
> +}
> +
> +module_init(esp32s3_acm_init);
> +module_exit(esp32s3_acm_exit);
> +
> +MODULE_DESCRIPTION("Espressif ESP32S3 USB ACM driver.");
> +MODULE_AUTHOR("Max Filippov <jcmvbkbc@xxxxxxxxx>");
> +MODULE_LICENSE("GPL");
> diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
> index ff076d6be159..1045bf096837 100644
> --- a/include/uapi/linux/serial_core.h
> +++ b/include/uapi/linux/serial_core.h
> @@ -248,4 +248,7 @@
>  /* Espressif ESP32 UART */
>  #define PORT_ESP32UART	124
>  
> +/* Espressif ESP32 ACM */
> +#define PORT_ESP32ACM	125
> +
>  #endif /* _UAPILINUX_SERIAL_CORE_H */
> 



[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux