Re: [PATCH v1 1/1] serial: 8250_bcm7271: Use dev_err_probe() instead of dev_err()

[Christophe JAILLET <christophe.jaillet@xxxxxxxxxx>]

Le 12/09/2023 à 18:55, Andy Shevchenko a écrit :
> Make the error messages format unified by switching to use
> dev_err_probe() where it makes sense.
>
> This also helps simplifing the code.
>
> Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
> ---
>   drivers/tty/serial/8250/8250_bcm7271.c | 17 +++++++----------
>   1 file changed, 7 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/tty/serial/8250/8250_bcm7271.c b/drivers/tty/serial/8250/8250_bcm7271.c
> index aa5aff046756..51c3eca8673c 100644
> --- a/drivers/tty/serial/8250/8250_bcm7271.c
> +++ b/drivers/tty/serial/8250/8250_bcm7271.c
> @@ -984,10 +984,9 @@ static int brcmuart_probe(struct platform_device *pdev)
>   	}
>   
>   	/* We should have just the uart base registers or all the registers */
> -	if (x != 1 && x != REGS_MAX) {
> -		dev_warn(dev, "%s registers not specified\n", reg_names[x]);
> -		return -EINVAL;
> -	}
> +	if (x != 1 && x != REGS_MAX)
> +		return dev_err_probe(dev, -EINVAL, "%s registers not specified\n",
> +				     reg_names[x]);
>   
>   	/* if the DMA registers were specified, try to enable DMA */
>   	if (x > REGS_DMA_RX) {
> @@ -1034,8 +1033,7 @@ static int brcmuart_probe(struct platform_device *pdev)
>   	}
>   
>   	if (clk_rate == 0) {
> -		dev_err(dev, "clock-frequency or clk not defined\n");
> -		ret = -EINVAL;
> +		ret = dev_err_probe(dev, -EINVAL, "clock-frequency or clk not defined\n");
>   		goto err_clk_disable;
>   	}
>   
> @@ -1093,7 +1091,7 @@ static int brcmuart_probe(struct platform_device *pdev)
>   
>   	ret = serial8250_register_8250_port(&up);
>   	if (ret < 0) {
> -		dev_err(dev, "unable to register 8250 port\n");
> +		dev_err_probe(dev, ret, "unable to register 8250 port\n");
>   		goto err;
>   	}
>   	priv->line = ret;
> @@ -1102,14 +1100,13 @@ static int brcmuart_probe(struct platform_device *pdev)
>   	if (priv->dma_enabled) {
>   		dma_irq = platform_get_irq_byname(pdev,  "dma");
>   		if (dma_irq < 0) {
> -			ret = dma_irq;
> -			dev_err(dev, "no IRQ resource info\n");
> +			dev_err_probe(dev, dma_irq, "no IRQ resource info\n");

ret = dev_err_probe(dev, dma_irq, "no IRQ resource info\n");

>   			goto err1;
>   		}
>   		ret = devm_request_irq(dev, dma_irq, brcmuart_isr,
>   				IRQF_SHARED, "uart DMA irq", &new_port->port);
>   		if (ret) {
> -			dev_err(dev, "unable to register IRQ handler\n");
> +			dev_err_probe(dev, ret, "unable to register IRQ handler\n");
>   			goto err1;
>   		}
>   	}