Re: [PATCH v3 09/11] serial: sc16is7xx: add I/O register translation offset

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, 25 May 2023, Hugo Villeneuve wrote:

> From: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
> 
> If the shared GPIO pins on a dual port/channel variant like the
> SC16IS752 are configured as GPIOs for port A, and modem control lines
> on port A, we need to translate the Linux GPIO offset to an offset
> that is compatible with the I/O registers of the SC16IS7XX (IOState,
> IODir and IOIntEna).
> 
> Add a new variable to store that offset and set it when we detect that
> special case.
> 
> Signed-off-by: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
> ---
>  drivers/tty/serial/sc16is7xx.c | 54 +++++++++++++++++++++++++++++++++-
>  1 file changed, 53 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
> index 97ec532a0a19..c2cfd057ed9a 100644
> --- a/drivers/tty/serial/sc16is7xx.c
> +++ b/drivers/tty/serial/sc16is7xx.c
> @@ -338,6 +338,7 @@ struct sc16is7xx_port {
>  #ifdef CONFIG_GPIOLIB
>  	struct gpio_chip		gpio;
>  	int				gpio_configured;
> +	int				gpio_offset;
>  #endif
>  	unsigned char			buf[SC16IS7XX_FIFO_SIZE];
>  	struct kthread_worker		kworker;
> @@ -1298,12 +1299,50 @@ static const struct uart_ops sc16is7xx_ops = {
>  };
>  
>  #ifdef CONFIG_GPIOLIB
> +
> +/*
> + * We may need to translate the Linux GPIO offset to a SC16IS7XX offset.
> + * This is needed only for the case where a dual port variant is configured to
> + * have only port B as modem status lines.
> + *
> + * Example for SC16IS752/762 with upper bank (port A) set as GPIOs, and
> + * lower bank (port B) set as modem status lines (special case described above):
> + *
> + * Pin         GPIO pin     Linux GPIO     SC16IS7XX
> + * name        function     offset         offset
> + * --------------------------------------------------
> + * GPIO7/RIA    GPIO7          3              7
> + * GPIO6/CDA    GPIO6          2              6
> + * GPIO5/DTRA   GPIO5          1              5
> + * GPIO4/DSRA   GPIO4          0              4
> + * GPIO3/RIB    RIB           N/A            N/A
> + * GPIO2/CDB    CDB           N/A            N/A
> + * GPIO1/DTRB   DTRB          N/A            N/A
> + * GPIO0/DSRB   DSRB          N/A            N/A
> + *
> + * Example  for SC16IS750/760 with upper bank (7..4) set as modem status lines,
> + * and lower bank (3..0) as GPIOs:
> + *
> + * Pin         GPIO pin     Linux GPIO     SC16IS7XX
> + * name        function     offset         offset
> + * --------------------------------------------------
> + * GPIO7/RI     RI            N/A            N/A
> + * GPIO6/CD     CD            N/A            N/A
> + * GPIO5/DTR    DTR           N/A            N/A
> + * GPIO4/DSR    DSR           N/A            N/A
> + * GPIO3        GPIO3          3              3
> + * GPIO2        GPIO2          2              2
> + * GPIO1        GPIO1          1              1
> + * GPIO0        GPIO0          0              0
> + */
> +
>  static int sc16is7xx_gpio_get(struct gpio_chip *chip, unsigned offset)
>  {
>  	unsigned int val;
>  	struct sc16is7xx_port *s = gpiochip_get_data(chip);
>  	struct uart_port *port = &s->p[0].port;
>  
> +	offset += s->gpio_offset;
>  	val = sc16is7xx_port_read(port, SC16IS7XX_IOSTATE_REG);
>  
>  	return !!(val & BIT(offset));
> @@ -1314,6 +1353,7 @@ static void sc16is7xx_gpio_set(struct gpio_chip *chip, unsigned offset, int val)
>  	struct sc16is7xx_port *s = gpiochip_get_data(chip);
>  	struct uart_port *port = &s->p[0].port;
>  
> +	offset += s->gpio_offset;
>  	sc16is7xx_port_update(port, SC16IS7XX_IOSTATE_REG, BIT(offset),
>  			      val ? BIT(offset) : 0);
>  }
> @@ -1324,6 +1364,7 @@ static int sc16is7xx_gpio_direction_input(struct gpio_chip *chip,
>  	struct sc16is7xx_port *s = gpiochip_get_data(chip);
>  	struct uart_port *port = &s->p[0].port;
>  
> +	offset += s->gpio_offset;
>  	sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset), 0);
>  
>  	return 0;
> @@ -1336,6 +1377,8 @@ static int sc16is7xx_gpio_direction_output(struct gpio_chip *chip,
>  	struct uart_port *port = &s->p[0].port;
>  	u8 state = sc16is7xx_port_read(port, SC16IS7XX_IOSTATE_REG);
>  
> +	offset += s->gpio_offset;
> +
>  	if (val)
>  		state |= BIT(offset);
>  	else
> @@ -1395,6 +1438,7 @@ static int sc16is7xx_probe(struct device *dev,
>  
>  #ifdef CONFIG_GPIOLIB
>  	s->gpio_configured = devtype->nr_gpio;
> +	s->gpio_offset = 0;
>  #endif /* CONFIG_GPIOLIB */
>  
>  	/* Always ask for fixed clock rate from a property. */
> @@ -1529,16 +1573,24 @@ static int sc16is7xx_probe(struct device *dev,
>  #endif /* CONFIG_GPIOLIB */
>  			}
>  
> -		if (val)
> +		if (val) {
> +#ifdef CONFIG_GPIOLIB
> +			/* Additional I/O regs offset. */
> +			if (val == SC16IS7XX_IOCONTROL_MODEM_B_BIT)
> +				s->gpio_offset = SC16IS7XX_GPIOS_PER_BANK;
> +#endif /* CONFIG_GPIOLIB */
> +
>  			regmap_update_bits(
>  				s->regmap,
>  				SC16IS7XX_IOCONTROL_REG << SC16IS7XX_REG_SHIFT,
>  				SC16IS7XX_IOCONTROL_MODEM_A_BIT |
>  				SC16IS7XX_IOCONTROL_MODEM_B_BIT, val);
> +		}
>  	}
>  
>  #ifdef CONFIG_GPIOLIB
>  	dev_dbg(dev, "GPIOs to configure: %d\n", s->gpio_configured);
> +	dev_dbg(dev, "GPIOs offset: %d\n", s->gpio_offset);
>  
>  	if (s->gpio_configured) {
>  		/* Setup GPIO controller */
> 

Is the order of this and 8/11 patch correct or should this precede that 
other patch? That is, is 8/11 alone useful enough or would this also be 
wanted? (I'm aware that 8/11 has a Fixes tag).

-- 
 i.




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux