Re: [PATCH v6 08/12] arm64: dts: nuvoton: Add initial ma35d1 device tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Dear Stephen,


Thanks for your advice.


On 2023/3/29 上午 01:57, Stephen Boyd wrote:
Quoting Jacky Huang (2023-03-27 19:19:08)
diff --git a/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi b/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi
new file mode 100644
index 000000000000..0740b0b218a7
--- /dev/null
+++ b/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi
@@ -0,0 +1,231 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2023 Nuvoton Technology Corp.
+ * Author: Shan-Chun Hung <schung@xxxxxxxxxxx>
+ *         Jacky huang <ychuang3@xxxxxxxxxxx>
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/nuvoton,ma35d1-clk.h>
+#include <dt-bindings/reset/nuvoton,ma35d1-reset.h>
+
+/ {
+       compatible = "nuvoton,ma35d1";
+       interrupt-parent = <&gic>;
+       #address-cells = <2>;
+       #size-cells = <2>;
+
+       cpus {
+               #address-cells = <2>;
+               #size-cells = <0>;
+
+               cpu0: cpu@0 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a35";
+                       reg = <0x0 0x0>;
+                       enable-method = "psci";
+                       next-level-cache = <&L2_0>;
+               };
+
+               cpu1: cpu@1 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a35";
+                       reg = <0x0 0x1>;
+                       enable-method = "psci";
+                       next-level-cache = <&L2_0>;
+               };
+
+               L2_0: l2-cache0 {
Just l2-cache for the node name. Doesn't it go under the cpu0 node as
well?

This describes the level-2 cache which is external to and shared by cpu0 & cpu1.
And only level-1 cache is inside of CPU core.
L2_0 is must, because both cpu0 and cpu1 has a next-level-cache = <&L2_0> property.

Many identical example of l2-cache node can be found in arm64 dts, such as k3-arm642.dtsi, rk3328.dtsi, mt8195.dtsi, etc. Here is just a copy of similar arm64 multi-core SoCs.

So we would like to keep this unchanged. Is it OK for you? Thanks.


+                       compatible = "cache";
+                       cache-level = <2>;
+               };
+       };
+
+       psci {
+               compatible = "arm,psci-0.2";
+               method = "smc";
+       };
+
+       timer {
+               compatible = "arm,armv8-timer";
+               interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
+                             IRQ_TYPE_LEVEL_LOW)>, /* Physical Secure */
+                            <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) |
+                             IRQ_TYPE_LEVEL_LOW)>, /* Physical Non-Secure */
+                            <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) |
+                             IRQ_TYPE_LEVEL_LOW)>, /* Virtual */
+                            <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) |
+                             IRQ_TYPE_LEVEL_LOW)>; /* Hypervisor */
+               clock-frequency = <12000000>;
Remove this property. The frequency should be read by the driver.

I will remove it.

+               interrupt-parent = <&gic>;
+       };
Please create an 'soc' node for the SoC to hold all the nodes that have
a reg property.

OK, we will use soc node in the next version.

+
+       sys: system-management@40460000 {
+               compatible = "nuvoton,ma35d1-sys", "syscon", "simple-mfd";
+               reg = <0x0 0x40460000 0x0 0x200>;
+
+               reset: reset-controller {
+                       compatible = "nuvoton,ma35d1-reset";
+                       #reset-cells = <1>;
+               };
+       };
+
+       clk: clock-controller@40460200 {
+               compatible = "nuvoton,ma35d1-clk", "syscon";
+               reg = <0x00000000 0x40460200 0x0 0x100>;
+               #clock-cells = <1>;
+               clocks = <&clk_hxt>;
+               nuvoton,sys = <&sys>;
+       };
It looks like the device at 40460000 is a reset and clock controller.
Just make it one node and register the clk or reset device as an
auxiliary device.

40460000 is for system control registers, including power contrl, multifunction pin control, usb phy control, IP reset control, power-on setting information, and many other miscellaneous controls. The registers of reset controller is only a subset of system control registers.

40460200 is for clock controller which is independent of the system control integration The register base of clock controller is very close to system controller, but in fact the two are independent.


+
+       gic: interrupt-controller@50801000 {
+               compatible = "arm,gic-400";
+               reg =   <0x0 0x50801000 0 0x1000>, /* GICD */
+                       <0x0 0x50802000 0 0x2000>, /* GICC */
+                       <0x0 0x50804000 0 0x2000>, /* GICH */
+                       <0x0 0x50806000 0 0x2000>; /* GICV */
+               #interrupt-cells = <3>;
+               interrupt-parent = <&gic>;
+               interrupt-controller;
+               interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0x13) |
+                             IRQ_TYPE_LEVEL_HIGH)>;
+       };
+
+       uart0:serial@40700000 {
Add a space after :

I will fix it. Thank you.

+               compatible = "nuvoton,ma35d1-uart";
+               reg = <0x0 0x40700000 0x0 0x100>;
+               interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+               clocks = <&clk UART0_GATE>;
+               status = "disabled";
+       };


Best regards,
Jacky Huang





[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux