As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode), it is mentioned
that, set the SCR.TIE bit to 0 and SCR.TEIE bit to 1, after the last
data to be transmitted are written to the TDR.
This will generate tx end interrupt and in the handler set SCR.TE and
SCR.TEIE to 0.
Signed-off-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
---
v3->v4:
* Removed fixes tag, as it is a feature enhancement to make tx fully
functional on RZ/G2L alike SOCs. With previous patch#3, eventhough
we get tx interrupts, still it is broken as characters entered on
uart terminal is not visible except for the first character.
v3:
* New patch
---
drivers/tty/serial/sh-sci.c | 31 ++++++++++++++++++++++++++++---
drivers/tty/serial/sh-sci.h | 3 +++
2 files changed, 31 insertions(+), 3 deletions(-)
diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index bcc4152ce043..da7eb7a3ca6f 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -861,9 +861,16 @@ static void sci_transmit_chars(struct uart_port *port)
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(port);
- if (uart_circ_empty(xmit))
- sci_stop_tx(port);
+ if (uart_circ_empty(xmit)) {
+ if (port->type == PORT_SCI) {
+ ctrl = serial_port_in(port, SCSCR);
+ ctrl &= ~SCSCR_TIE;
+ ctrl |= SCSCR_TEIE;
+ serial_port_out(port, SCSCR, ctrl);
+ }
+ sci_stop_tx(port);
+ }
}
static void sci_receive_chars(struct uart_port *port)
@@ -1752,6 +1759,24 @@ static irqreturn_t sci_tx_interrupt(int irq, void *ptr)
return IRQ_HANDLED;
}
+static irqreturn_t sci_tx_end_interrupt(int irq, void *ptr)
+{
+ struct uart_port *port = ptr;
+ unsigned long flags;
+ unsigned short ctrl;
+
+ if (port->type != PORT_SCI)
+ return sci_tx_interrupt(irq, ptr);
+
+ spin_lock_irqsave(&port->lock, flags);
+ ctrl = serial_port_in(port, SCSCR);
+ ctrl &= ~(SCSCR_TE | SCSCR_TEIE);
+ serial_port_out(port, SCSCR, ctrl);
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ return IRQ_HANDLED;
+}
+
static irqreturn_t sci_br_interrupt(int irq, void *ptr)
{
struct uart_port *port = ptr;
@@ -1888,7 +1913,7 @@ static const struct sci_irq_desc {
[SCIx_TEI_IRQ] = {
.desc = "tx end",
- .handler = sci_tx_interrupt,
+ .handler = sci_tx_end_interrupt,
},
/*
diff --git a/drivers/tty/serial/sh-sci.h b/drivers/tty/serial/sh-sci.h
index c0ae78632dda..0b65563c4e9e 100644
--- a/drivers/tty/serial/sh-sci.h
+++ b/drivers/tty/serial/sh-sci.h
@@ -59,6 +59,9 @@ enum {
#define SCSMR_SRC_19 0x0600 /* Sampling rate 1/19 */
#define SCSMR_SRC_27 0x0700 /* Sampling rate 1/27 */
+/* Serial Control Register, SCI only bits */
+#define SCSCR_TEIE BIT(2) /* Transmit End Interrupt Enable */
+
/* Serial Control Register, SCIFA/SCIFB only bits */
#define SCSCR_TDRQE BIT(15) /* Tx Data Transfer Request Enable */
#define SCSCR_RDRQE BIT(14) /* Rx Data Transfer Request Enable */
--
2.25.1
