Hi,
I'll not note all things below because others have already seemingly
commented many things.
On Wed, 15 Mar 2023, Jacky Huang wrote:
> From: Jacky Huang <ychuang3@xxxxxxxxxxx>
>
> This adds UART and console driver for Nuvoton ma35d1 Soc.
>
> MA35D1 SoC provides up to 17 UART controllers, each with one uart port.
> The ma35d1 uart controller is not compatible with 8250.
> The uart controller supports:
> - Full-duplex asynchronous communications
> - Separates tx and tx 32/32 bytes entry FIFO for data payloads
> - Hardware auto-flow control
> - Programmable rx buffer trigger level (1/4/8/14/30 bytes)
> - Individual programmable baud rate generator for each channel
> - Supports nCTS, incoming data, rx FIFO reached threshold and
> RS-485 Address Match (AAD mode) wake-up function
> - Supports 8-bit rx buffer time-out detection function
> - Programmable tx data delay time
> - Supports Auto-Baud Rate measurement and baud rate compensation
> - Supports break error, frame error, parity error and rx/tx buffer
> overflow detection function
> – Programmable number of data bit, 5-, 6-, 7-, 8- bit character
> – Programmable parity bit, even, odd, no parity or stick parity bit
> generation and detection
> – Programmable stop bit, 1, 1.5, or 2 stop bit generation
> - Supports IrDA SIR function mode
> - Supports RS-485 function mode
> – Supports RS-485 9-bit mode
> – Supports hardware or software enables to program nRTS pin to control
> RS-485 transmission direction
> - Supports PDMA transfer function
> - Support Single-wire function mode.
This list is probably copy-pasted from somewhere but it doesn't match what
you implemented in the driver.
> Signed-off-by: Jacky Huang <ychuang3@xxxxxxxxxxx>
> ---
> drivers/tty/serial/Kconfig | 18 +
> drivers/tty/serial/Makefile | 1 +
> drivers/tty/serial/ma35d1_serial.c | 842 +++++++++++++++++++++++++++++
> drivers/tty/serial/ma35d1_serial.h | 93 ++++
> include/uapi/linux/serial_core.h | 3 +
> 5 files changed, 957 insertions(+)
> create mode 100644 drivers/tty/serial/ma35d1_serial.c
> create mode 100644 drivers/tty/serial/ma35d1_serial.h
>
> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> index 625358f44419..cb47fe804595 100644
> --- a/drivers/tty/serial/Kconfig
> +++ b/drivers/tty/serial/Kconfig
> @@ -1562,6 +1562,24 @@ config SERIAL_SUNPLUS_CONSOLE
> you can alter that using a kernel command line option such as
> "console=ttySUPx".
>
> +config SERIAL_NUVOTON_MA35D1
> + tristate "Nuvoton MA35D1 family UART support"
> + depends on ARCH_NUVOTON || COMPILE_TEST
> + select SERIAL_CORE
> + help
> + This driver supports Nuvoton MA35D1 family UART ports. If you would
> + like to use them, you must answer Y or M to this option. Note that
> + for use as console, it must be included in kernel and not as a
> + module
> +
> +config SERIAL_NUVOTON_MA35D1_CONSOLE
> + bool "Console on a Nuvotn MA35D1 family UART port"
> + depends on SERIAL_NUVOTON_MA35D1=y
> + select SERIAL_CORE_CONSOLE
> + help
> + Select this options if you'd like to use the UART port0 of the
> + Nuvoton MA35D1 family as a console.
> +
> endmenu
>
> config SERIAL_MCTRL_GPIO
> diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
> index cd9afd9e3018..71ebeba06ff2 100644
> --- a/drivers/tty/serial/Makefile
> +++ b/drivers/tty/serial/Makefile
> @@ -93,3 +93,4 @@ obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
>
> obj-$(CONFIG_SERIAL_KGDB_NMI) += kgdb_nmi.o
> obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
> +obj-$(CONFIG_SERIAL_NUVOTON_MA35D1) += ma35d1_serial.o
> diff --git a/drivers/tty/serial/ma35d1_serial.c b/drivers/tty/serial/ma35d1_serial.c
> new file mode 100644
> index 000000000000..8940d07c3777
> --- /dev/null
> +++ b/drivers/tty/serial/ma35d1_serial.c
> @@ -0,0 +1,842 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * MA35D1 serial driver
> + * Copyright (C) 2023 Nuvoton Technology Corp.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/moduleparam.h>
> +#include <linux/ioport.h>
> +#include <linux/init.h>
> +#include <linux/console.h>
> +#include <linux/sysrq.h>
> +#include <linux/delay.h>
> +#include <linux/platform_device.h>
> +#include <linux/tty.h>
> +#include <linux/tty_flip.h>
> +#include <linux/clk.h>
> +#include <linux/serial_reg.h>
> +#include <linux/serial_core.h>
> +#include <linux/serial.h>
> +#include <linux/nmi.h>
> +#include <linux/mutex.h>
> +#include <linux/slab.h>
> +#include <linux/uaccess.h>
> +#include <linux/of.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_address.h>
> +#include <linux/of_platform.h>
> +#include <linux/io.h>
> +#include <asm/irq.h>
> +#include <asm/serial.h>
> +#include "ma35d1_serial.h"
> +
> +#define UART_NR 17
> +
> +static struct uart_driver ma35d1serial_reg;
> +struct clk *clk;
> +
> +struct uart_ma35d1_port {
> + struct uart_port port;
> + u16 capabilities; /* port capabilities */
> + u8 ier;
> + u8 lcr;
> + u8 mcr;
> + u8 mcr_mask; /* mask of user bits */
> + u8 mcr_force; /* mask of forced bits */
> + struct serial_rs485 rs485; /* rs485 settings */
> + u32 baud_rate;
> + int rx_count;
> + u32 console_baud_rate;
> + u32 console_line;
> + u32 console_int;
> +};
> +
> +static struct device_node *ma35d1serial_uart_nodes[UART_NR];
> +static struct uart_ma35d1_port ma35d1serial_ports[UART_NR] = { 0 };
> +static void __stop_tx(struct uart_ma35d1_port *p);
> +static void transmit_chars(struct uart_ma35d1_port *up);
Try to rearrange such that forward declarations are not necessary for
functions.
> +static struct uart_ma35d1_port *to_ma35d1_uart_port(struct uart_port *uart)
static inline
> +{
> + return container_of(uart, struct uart_ma35d1_port, port);
> +}
> +
> +static u32 serial_in(struct uart_ma35d1_port *p, int offset)
> +{
> + return __raw_readl(p->port.membase + offset);
> +}
> +
> +static void serial_out(struct uart_ma35d1_port *p, int offset, int value)
> +{
> + __raw_writel(value, p->port.membase + offset);
> +}
> +
> +static void __stop_tx(struct uart_ma35d1_port *p)
> +{
> + u32 ier;
> +
> + ier = serial_in(p, UART_REG_IER);
> + if (ier & THRE_IEN)
> + serial_out(p, UART_REG_IER, ier & ~THRE_IEN);
> +}
> +
> +static void ma35d1serial_stop_tx(struct uart_port *port)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> +
> + __stop_tx(up);
> +}
> +
> +static void ma35d1serial_start_tx(struct uart_port *port)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> + u32 ier;
> + struct circ_buf *xmit = &up->port.state->xmit;
> +
> + ier = serial_in(up, UART_REG_IER);
> + serial_out(up, UART_REG_IER, ier & ~THRE_IEN);
> + if (uart_circ_chars_pending(xmit) <
> + (16 - ((serial_in(up, UART_REG_FSR) >> 16) & 0x3F)))
> + transmit_chars(up);
> + serial_out(up, UART_REG_IER, ier | THRE_IEN);
> +}
> +
> +static void ma35d1serial_stop_rx(struct uart_port *port)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> +
> + serial_out(up, UART_REG_IER, serial_in(up, UART_REG_IER) & ~RDA_IEN);
> +}
> +
> +static void
> +receive_chars(struct uart_ma35d1_port *up)
> +{
> + u8 ch;
> + u32 fsr;
> + u32 isr;
> + u32 dcnt;
> + char flag;
> +
> + isr = serial_in(up, UART_REG_ISR);
> + fsr = serial_in(up, UART_REG_FSR);
> +
> + while (!(fsr & RX_EMPTY)) {
> + flag = TTY_NORMAL;
> + up->port.icount.rx++;
> +
> + if (unlikely(fsr & (BIF | FEF | PEF | RX_OVER_IF))) {
> + if (fsr & BIF) {
> + serial_out(up, UART_REG_FSR, BIF);
> + up->port.icount.brk++;
> + if (uart_handle_break(&up->port))
> + continue;
> + }
> + if (fsr & FEF) {
> + serial_out(up, UART_REG_FSR, FEF);
> + up->port.icount.frame++;
> + }
> + if (fsr & PEF) {
> + serial_out(up, UART_REG_FSR, PEF);
> + up->port.icount.parity++;
> + }
> + if (fsr & RX_OVER_IF) {
> + serial_out(up, UART_REG_FSR, RX_OVER_IF);
> + up->port.icount.overrun++;
> + }
Do you need to write each of those individually to clear(?) them or could
you just do one write here after the accounting is done:
serial_out(up, UART_REG_FSR, fsr & (BIF|FEF|PEF|RX_OVER_IF));
?
Also, add some driver specific prefix for the flag naming (all driver
specific ones, not just these if you have others besides these).
> + if (fsr & BIF)
> + flag = TTY_BREAK;
> + if (fsr & PEF)
> + flag = TTY_PARITY;
> + if (fsr & FEF)
> + flag = TTY_FRAME;
Are you sure this is the right prioritization or do you perhaps want else
ifs like in some other serial drivers?
> + }
> + ch = (u8)serial_in(up, UART_REG_RBR);
Drop the case.
> + if (uart_handle_sysrq_char(&up->port, ch))
> + continue;
> +
> + uart_insert_char(&up->port, fsr, RX_OVER_IF, ch, flag);
> + up->rx_count++;
> + dcnt = (serial_in(up, UART_REG_FSR) >> 8) & 0x3f;
> + if (up->rx_count > 1023) {
> + spin_lock(&up->port.lock);
> + tty_flip_buffer_push(&up->port.state->port);
> + spin_unlock(&up->port.lock);
> + up->rx_count = 0;
Why is all this ->rx_count trickery necessary? What's so special with the
size in question?
> + if ((isr & RXTO_IF) && (dcnt == 0))
> + goto tout_end;
> + }
> + if (isr & RDA_IF) {
> + if (dcnt == 1)
Merge to the same comdition.
dcnt could probably have a more descriptive name.
> + return;
> + }
> + fsr = serial_in(up, UART_REG_FSR);
> + }
> + spin_lock(&up->port.lock);
> + tty_flip_buffer_push(&up->port.state->port);
> + spin_unlock(&up->port.lock);
> +tout_end:
> + up->rx_count = 0;
> +}
> +
> +static void transmit_chars(struct uart_ma35d1_port *up)
> +{
> + struct circ_buf *xmit = &up->port.state->xmit;
> + int count = 16 - ((serial_in(up, UART_REG_FSR) >> 16) & 0xF);
> +
> + if (serial_in(up, UART_REG_FSR) & TX_FULL)
> + count = 0;
> + if (up->port.x_char) {
> + serial_out(up, UART_REG_THR, up->port.x_char);
> + up->port.icount.tx++;
> + up->port.x_char = 0;
> + return;
> + }
> + if (uart_tx_stopped(&up->port)) {
> + ma35d1serial_stop_tx(&up->port);
> + return;
> + }
> + if (uart_circ_empty(xmit)) {
> + __stop_tx(up);
> + return;
> + }
> + while (count > 0) {
> + serial_out(up, UART_REG_THR, xmit->buf[xmit->tail]);
> + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
> + up->port.icount.tx++;
> + count--;
> + if (uart_circ_empty(xmit))
> + break;
> + }
> + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
> + uart_write_wakeup(&up->port);
> + if (uart_circ_empty(xmit))
> + __stop_tx(up);
> +}
> +
> +static irqreturn_t ma35d1serial_interrupt(int irq, void *dev_id)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)dev_id;
> + u32 isr, fsr;
> +
> + isr = serial_in(up, UART_REG_ISR);
> + fsr = serial_in(up, UART_REG_FSR);
> + if (isr & (RDA_IF | RXTO_IF))
> + receive_chars(up);
> + if (isr & THRE_INT)
> + transmit_chars(up);
> + if (fsr & (BIF | FEF | PEF | RX_OVER_IF | TX_OVER_IF))
> + serial_out(up, UART_REG_FSR,
> + (BIF | FEF | PEF | RX_OVER_IF | TX_OVER_IF));
Hmm... Why write these again here... Didn't receive_chars() already
clear(?) most of these bits??
> +
> + return IRQ_HANDLED;
> +}
> +
> +static u32 ma35d1serial_tx_empty(struct uart_port *port)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> + u32 fsr;
> +
> + fsr = serial_in(up, UART_REG_FSR);
> + return (fsr & (TE_FLAG | TX_EMPTY)) == (TE_FLAG | TX_EMPTY) ?
> + TIOCSER_TEMT : 0;
> +}
> +
> +static u32 ma35d1serial_get_mctrl(struct uart_port *port)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> + u32 status;
> + u32 ret = 0;
> +
> + status = serial_in(up, UART_REG_MSR);
> + if (!(status & 0x10))
> + ret |= TIOCM_CTS;
> + return ret;
> +}
> +
> +static void ma35d1serial_set_mctrl(struct uart_port *port, u32 mctrl)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> + u32 mcr = 0;
> + u32 ier = 0;
> +
> + if (mctrl & TIOCM_RTS) {
> + /* set RTS high level trigger */
> + mcr = serial_in(up, UART_REG_MCR);
> + mcr |= 0x200;
> + mcr &= ~(0x2);
> + }
> + if (up->mcr & UART_MCR_AFE) {
> + /* set RTS high level trigger */
> + mcr = serial_in(up, UART_REG_MCR);
> + mcr |= 0x200;
> + mcr &= ~(0x2);
> +
> + /* enable CTS/RTS auto-flow control */
> + serial_out(up, UART_REG_IER,
> + (serial_in(up, UART_REG_IER) | (0x3000)));
Once you have named the bits probably with defines, most of the comments
such as the one above are rendered redundant and should be dropped.
> +
> + /* Set hardware flow control */
> + up->port.flags |= UPF_HARD_FLOW;
> + } else {
> + /* disable CTS/RTS auto-flow control */
> + ier = serial_in(up, UART_REG_IER);
> + ier &= ~(0x3000);
> + serial_out(up, UART_REG_IER, ier);
> +
> + /* un-set hardware flow control */
> + up->port.flags &= ~UPF_HARD_FLOW;
> + }
> +
> + /* set CTS high level trigger */
> + serial_out(up, UART_REG_MSR, (serial_in(up, UART_REG_MSR) | (0x100)));
> + serial_out(up, UART_REG_MCR, mcr);
> +}
> +
> +static void ma35d1serial_break_ctl(struct uart_port *port, int break_state)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> + unsigned long flags;
> + u32 lcr;
> +
> + spin_lock_irqsave(&up->port.lock, flags);
> + lcr = serial_in(up, UART_REG_LCR);
> + if (break_state != 0)
> + lcr |= BCB; /* set break */
> + else
> + lcr &= ~BCB; /* clr break */
While BCB might come from HW naming, a better name for would make these
very obvious (and the comments unnecessary).
> + serial_out(up, UART_REG_LCR, lcr);
> + spin_unlock_irqrestore(&up->port.lock, flags);
> +}
> +
> +static int ma35d1serial_startup(struct uart_port *port)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> + struct tty_struct *tty = port->state->port.tty;
> + int retval;
> +
> + /* Reset FIFO */
> + serial_out(up, UART_REG_FCR, TFR | RFR /* | RX_DIS */);
> +
> + /* Clear pending interrupts */
> + serial_out(up, UART_REG_ISR, 0xFFFFFFFF);
~0 is another option.
> +
> + retval = request_irq(port->irq, ma35d1serial_interrupt, 0,
> + tty ? tty->name : "ma35d1_serial", port);
Why such exceptional name trickery?
> + if (retval) {
> + dev_err(up->port.dev, "request irq failed.\n");
> + return retval;
> + }
> +
> + /* Now, initialize the UART */
> + /* FIFO trigger level 4 byte */
> + /* RTS trigger level 8 bytes */
> + serial_out(up, UART_REG_FCR,
> + serial_in(up, UART_REG_FCR) | 0x10 | 0x20000);
> + serial_out(up, UART_REG_LCR, 0x7); /* 8 bit */
> + serial_out(up, UART_REG_TOR, 0x40);
> + serial_out(up, UART_REG_IER,
> + RTO_IEN | RDA_IEN | TIME_OUT_EN | BUFERR_IEN);
> + return 0;
> +}
> +
> +static void ma35d1serial_shutdown(struct uart_port *port)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> +
> + free_irq(port->irq, port);
> +
> + /* Disable interrupts from this port */
> + serial_out(up, UART_REG_IER, 0);
> +}
> +
> +static u32 ma35d1serial_get_divisor(struct uart_port *port, u32 baud)
> +{
> + u32 quot;
> +
> + quot = (port->uartclk / baud) - 2;
Unnecessary parenthesis. (+Somebody already commented about the
unnecessary variable.)
> + return quot;
> +}
> +
> +static void ma35d1serial_set_termios(struct uart_port *port,
> + struct ktermios *termios,
> + const struct ktermios *old)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> + u32 lcr = 0;
> + unsigned long flags;
> + u32 baud, quot;
> +
> + switch (termios->c_cflag & CSIZE) {
> + case CS5:
> + lcr = 0;
> + break;
> + case CS6:
> + lcr |= 1;
> + break;
> + case CS7:
> + lcr |= 2;
> + break;
> + case CS8:
> + default:
> + lcr |= 3;
> + break;
> + }
> +
> + if (termios->c_cflag & CSTOPB)
> + lcr |= NSB;
> + if (termios->c_cflag & PARENB)
> + lcr |= PBE;
> + if (!(termios->c_cflag & PARODD))
> + lcr |= EPE;
> + if (termios->c_cflag & CMSPAR)
> + lcr |= SPE;
> +
> + baud = uart_get_baud_rate(port, termios, old, port->uartclk / 0xffff,
> + port->uartclk / 11);
> +
> + quot = ma35d1serial_get_divisor(port, baud);
> +
> + /*
> + * Ok, we're now changing the port state. Do it with
> + * interrupts disabled.
> + */
> + spin_lock_irqsave(&up->port.lock, flags);
> +
> + up->port.read_status_mask = RX_OVER_IF;
> + if (termios->c_iflag & INPCK)
> + up->port.read_status_mask |= FEF | PEF;
> + if (termios->c_iflag & (BRKINT | PARMRK))
> + up->port.read_status_mask |= BIF;
> +
> + /*
> + * Characteres to ignore
> + */
> + up->port.ignore_status_mask = 0;
> + if (termios->c_iflag & IGNPAR)
> + up->port.ignore_status_mask |= FEF | PEF;
> + if (termios->c_iflag & IGNBRK) {
> + up->port.ignore_status_mask |= BIF;
> + /*
> + * If we're ignoring parity and break indicators,
> + * ignore overruns too (for real raw support).
> + */
> + if (termios->c_iflag & IGNPAR)
> + up->port.ignore_status_mask |= RX_OVER_IF;
> + }
> + if (termios->c_cflag & CRTSCTS)
> + up->mcr |= UART_MCR_AFE;
> + else
> + up->mcr &= ~UART_MCR_AFE;
> +
> + ma35d1serial_set_mctrl(&up->port, up->port.mctrl);
> + serial_out(up, UART_REG_BAUD, quot | 0x30000000);
> + serial_out(up, UART_REG_LCR, lcr);
You need to do uart_update_timeout() in the set_termios function.
> + spin_unlock_irqrestore(&up->port.lock, flags);
> +}
> +
> +static void ma35d1serial_release_port(struct uart_port *port)
> +{
> + iounmap(port->membase);
> + port->membase = NULL;
> +}
> +
> +static int ma35d1serial_request_port(struct uart_port *port)
> +{
> + return 0;
> +}
> +
> +static void ma35d1serial_config_port(struct uart_port *port, int flags)
> +{
> + int ret;
> +
> + /*
> + * Find the region that we can probe for. This in turn
> + * tells us whether we can probe for the type of port.
> + */
> + ret = ma35d1serial_request_port(port);
> + if (ret < 0)
> + return;
> + port->type = PORT_MA35D1;
> +}
> +
> +static int ma35d1serial_verify_port(struct uart_port *port,
> + struct serial_struct *ser)
> +{
> + if (ser->type != PORT_UNKNOWN && ser->type != PORT_MA35D1)
> + return -EINVAL;
> + return 0;
> +}
> +
> +static const char *ma35d1serial_type(struct uart_port *port)
> +{
> + return (port->type == PORT_MA35D1) ? "MA35D1" : NULL;
> +}
> +
> +/* Enable or disable the rs485 support */
> +static int ma35d1serial_config_rs485(struct uart_port *port,
> + struct ktermios *termios,
> + struct serial_rs485 *rs485conf)
> +{
> + struct uart_ma35d1_port *p = to_ma35d1_uart_port(port);
> +
> + p->rs485 = *rs485conf;
> +
> + if (p->rs485.delay_rts_before_send >= 1000)
> + p->rs485.delay_rts_before_send = 1000;
Don't do this in driver, the core handles the delay limits. You don't seem
to be using the value anyway for anything???
Please separate the RS485 support into its own patch.
> + serial_out(p, UART_FUN_SEL,
> + (serial_in(p, UART_FUN_SEL) & ~FUN_SEL_MASK));
> +
> + if (rs485conf->flags & SER_RS485_ENABLED) {
> + serial_out(p, UART_FUN_SEL,
> + (serial_in(p, UART_FUN_SEL) | FUN_SEL_RS485));
Does this pair of serial_out()s glitch the RS485 line if ->rs485_config()
is called while RS485 mode is already set?
Why you need to do serial_in() from the UART_FUN_SEL twice?
> +
> + if (rs485conf->flags & SER_RS485_RTS_ON_SEND)
> + serial_out(p, UART_REG_MCR,
> + (serial_in(p, UART_REG_MCR) & ~0x200));
> + else
> + serial_out(p, UART_REG_MCR,
> + (serial_in(p, UART_REG_MCR) | 0x200));
> +
> + /* set auto direction mode */
> + serial_out(p, UART_REG_ALT_CSR,
> + (serial_in(p, UART_REG_ALT_CSR) | (1 << 10)));
> + }
> + return 0;
> +}
> +
> +static int ma35d1serial_ioctl(struct uart_port *port, u32 cmd, unsigned long arg)
> +{
> + switch (cmd) {
> + default:
> + return -ENOIOCTLCMD;
> + }
> + return 0;
> +}
> +
> +static const struct uart_ops ma35d1serial_ops = {
> + .tx_empty = ma35d1serial_tx_empty,
> + .set_mctrl = ma35d1serial_set_mctrl,
> + .get_mctrl = ma35d1serial_get_mctrl,
> + .stop_tx = ma35d1serial_stop_tx,
> + .start_tx = ma35d1serial_start_tx,
> + .stop_rx = ma35d1serial_stop_rx,
> + .break_ctl = ma35d1serial_break_ctl,
> + .startup = ma35d1serial_startup,
> + .shutdown = ma35d1serial_shutdown,
> + .set_termios = ma35d1serial_set_termios,
> + .type = ma35d1serial_type,
> + .release_port = ma35d1serial_release_port,
> + .request_port = ma35d1serial_request_port,
> + .config_port = ma35d1serial_config_port,
> + .verify_port = ma35d1serial_verify_port,
> + .ioctl = ma35d1serial_ioctl,
> +};
> +
> +static const struct of_device_id ma35d1_serial_of_match[] = {
> + { .compatible = "nuvoton,ma35d1-uart" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ma35d1_serial_of_match);
> +
> +#ifdef CONFIG_SERIAL_NUVOTON_MA35D1_CONSOLE
> +
> +static void ma35d1serial_console_putchar(struct uart_port *port,
> + unsigned char ch)
> +{
> + struct uart_ma35d1_port *up = (struct uart_ma35d1_port *)port;
> +
> + do {
> + } while ((serial_in(up, UART_REG_FSR) & TX_FULL));
> + serial_out(up, UART_REG_THR, ch);
> +}
> +
> +/*
> + * Print a string to the serial port trying not to disturb
> + * any possible real use of the port...
> + *
> + * The console_lock must be held when we get here.
> + */
> +static void ma35d1serial_console_write(struct console *co,
> + const char *s, u32 count)
> +{
> + struct uart_ma35d1_port *up = &ma35d1serial_ports[co->index];
> + unsigned long flags;
> + u32 ier;
> +
> + local_irq_save(flags);
> +
> + /*
> + * First save the IER then disable the interrupts
> + */
> + ier = serial_in(up, UART_REG_IER);
> + serial_out(up, UART_REG_IER, 0);
> +
> + uart_console_write(&up->port, s, count, ma35d1serial_console_putchar);
> +
> + /*
> + * Finally, wait for transmitter to become empty
> + * and restore the IER
> + */
> + do {
> + } while (!(serial_in(up, UART_REG_FSR) & TX_EMPTY));
> + serial_out(up, UART_REG_IER, ier);
> + local_irq_restore(flags);
> +}
> +
> +static int __init ma35d1serial_console_setup(struct console *co,
> + char *options)
> +{
> + struct device_node *np = ma35d1serial_uart_nodes[co->index];
> + struct uart_ma35d1_port *p = &ma35d1serial_ports[co->index];
> + u32 val32[4];
> + struct uart_port *port;
> + int baud = 115200;
> + int bits = 8;
> + int parity = 'n';
> + int flow = 'n';
> +
> + /*
> + * Check whether an invalid uart number has been specified, and
> + * if so, search for the first available port that does have
> + * console support.
> + */
> + if ((co->index < 0) || (co->index >= UART_NR)) {
> + pr_debug("Console Port%x out of range\n", co->index);
> + return -EINVAL;
> + }
> +
> + if (of_property_read_u32_array(np, "reg", val32, 4) != 0)
> + return -EINVAL;
> + p->port.iobase = val32[1];
> + p->port.membase = ioremap(p->port.iobase, 0x10000);
> + p->port.ops = &ma35d1serial_ops;
> + p->port.line = 0;
> + p->port.uartclk = 24000000;
> +
> + port = &ma35d1serial_ports[co->index].port;
> + return uart_set_options(port, co, baud, parity, bits, flow);
> +}
> +
> +static struct console ma35d1serial_console = {
> + .name = "ttyS",
> + .write = ma35d1serial_console_write,
> + .device = uart_console_device,
> + .setup = ma35d1serial_console_setup,
> + .flags = CON_PRINTBUFFER | CON_ENABLED,
> + .index = -1,
> + .data = &ma35d1serial_reg,
> +};
> +
> +static void
> +ma35d1serial_console_init_port(void)
> +{
> + int i = 0;
> + struct device_node *np;
> +
> + for_each_matching_node(np, ma35d1_serial_of_match) {
> + if (ma35d1serial_uart_nodes[i] == NULL) {
> + ma35d1serial_uart_nodes[i] = np;
> + i++;
> + }
> + }
> +}
> +
> +static int __init ma35d1serial_console_init(void)
> +{
> + ma35d1serial_console_init_port();
> + register_console(&ma35d1serial_console);
> + return 0;
> +}
> +console_initcall(ma35d1serial_console_init);
> +
> +#define MA35D1SERIAL_CONSOLE (&ma35d1serial_console)
> +#else
> +#define MA35D1SERIAL_CONSOLE NULL
> +#endif
> +
> +static struct uart_driver ma35d1serial_reg = {
> + .owner = THIS_MODULE,
> + .driver_name = "serial",
> + .dev_name = "ttyS",
> + .major = TTY_MAJOR,
> + .minor = 64,
> + .cons = MA35D1SERIAL_CONSOLE,
> + .nr = UART_NR,
> +};
> +
> +/**
> + * Suspend one serial port.
> + */
> +void ma35d1serial_suspend_port(int line)
> +{
> + uart_suspend_port(&ma35d1serial_reg, &ma35d1serial_ports[line].port);
> +}
> +EXPORT_SYMBOL(ma35d1serial_suspend_port);
> +
> +/**
> + * Resume one serial port.
> + */
> +void ma35d1serial_resume_port(int line)
> +{
> + struct uart_ma35d1_port *up = &ma35d1serial_ports[line];
> +
> + uart_resume_port(&ma35d1serial_reg, &up->port);
> +}
> +EXPORT_SYMBOL(ma35d1serial_resume_port);
> +
> +/*
> + * Register a set of serial devices attached to a platform device.
> + * The list is terminated with a zero flags entry, which means we expect
> + * all entries to have at least UPF_BOOT_AUTOCONF set.
> + */
> +static int ma35d1serial_probe(struct platform_device *pdev)
> +{
> + struct resource *res_mem;
> + struct uart_ma35d1_port *up;
> + int ret;
> + struct clk *clk;
> + int err;
> +
> + if (pdev->dev.of_node) {
> + ret = of_alias_get_id(pdev->dev.of_node, "serial");
> + if (ret < 0) {
> + dev_err(&pdev->dev,
> + "failed to get alias/pdev id, errno %d\n",
> + ret);
Just put error prints to one line if you don't break 100 chars limit.
> + return ret;
Misaligned line.
> + }
> + }
> + up = &ma35d1serial_ports[ret];
> + up->port.line = ret;
> + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res_mem)
> + return -ENODEV;
> +
> + up->port.iobase = res_mem->start;
> + up->port.membase = ioremap(up->port.iobase, 0x10000);
Define for the literal.
> + up->port.ops = &ma35d1serial_ops;
> +
> + spin_lock_init(&up->port.lock);
> +
> + clk = of_clk_get(pdev->dev.of_node, 0);
> + if (IS_ERR(clk)) {
> + err = PTR_ERR(clk);
> + dev_err(&pdev->dev, "failed to get core clk: %d\n", err);
> + return -ENOENT;
> + }
> + err = clk_prepare_enable(clk);
> + if (err)
> + return -ENOENT;
> +
> + if (up->port.line != 0)
> + up->port.uartclk = clk_get_rate(clk);
> + up->port.irq = platform_get_irq(pdev, 0);
> + up->port.dev = &pdev->dev;
> + up->port.flags = UPF_BOOT_AUTOCONF;
> + up->port.rs485_config = ma35d1serial_config_rs485;
Please provide also .rs485_supported for the serial core to handle the
supported features for you.
> + ret = uart_add_one_port(&ma35d1serial_reg, &up->port);
> + platform_set_drvdata(pdev, up);
> + return 0;
> +}
> +
> +/*
> + * Remove serial ports registered against a platform device.
> + */
> +static int ma35d1serial_remove(struct platform_device *dev)
> +{
> + int i;
> + struct uart_port *port = platform_get_drvdata(dev);
> +
> + free_irq(port->irq, port);
> + for (i = 0; i < UART_NR; i++) {
> + struct uart_ma35d1_port *up = &ma35d1serial_ports[i];
> +
> + if (up->port.dev == &dev->dev)
> + uart_remove_one_port(&ma35d1serial_reg, &up->port);
> + }
> + return 0;
> +}
> +
> +static int ma35d1serial_suspend(struct platform_device *dev,
> + pm_message_t state)
> +{
> + int i;
> + struct uart_ma35d1_port *up;
> +
> + if (dev->dev.of_node)
> + i = of_alias_get_id(dev->dev.of_node, "serial");
> + if (i < 0) {
> + dev_err(&dev->dev, "failed to get alias/pdev id, errno %d\n",
> + i);
Just put this to the same line with the rest.
> + return i;
> + }
> + up = &ma35d1serial_ports[i];
> + if (i == 0) {
> + up->console_baud_rate = serial_in(up, UART_REG_BAUD);
> + up->console_line = serial_in(up, UART_REG_LCR);
> + up->console_int = serial_in(up, UART_REG_IER);
> + }
> + return 0;
> +}
> +
> +static int ma35d1serial_resume(struct platform_device *dev)
> +{
> + int i;
> + struct uart_ma35d1_port *up;
> +
> + if (dev->dev.of_node)
> + i = of_alias_get_id(dev->dev.of_node, "serial");
> + if (i < 0) {
> + dev_err(&dev->dev, "failed to get alias/pdev id, errno %d\n",
> + i);
Same line.
> + return i;
> + }
> + up = &ma35d1serial_ports[i];
> + if (i == 0) {
> + serial_out(up, UART_REG_BAUD, up->console_baud_rate);
> + serial_out(up, UART_REG_LCR, up->console_line);
> + serial_out(up, UART_REG_IER, up->console_int);
> + }
> + return 0;
> +}
> +
> +static struct platform_driver ma35d1serial_driver = {
> + .probe = ma35d1serial_probe,
> + .remove = ma35d1serial_remove,
> + .suspend = ma35d1serial_suspend,
> + .resume = ma35d1serial_resume,
> + .driver = {
> + .name = "ma35d1-uart",
> + .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(ma35d1_serial_of_match),
> + },
> +};
> +
> +static int __init ma35d1serial_init(void)
> +{
> + int ret;
> +
> + ret = uart_register_driver(&ma35d1serial_reg);
> + if (ret)
> + return ret;
> + ret = platform_driver_register(&ma35d1serial_driver);
> + if (ret)
> + uart_unregister_driver(&ma35d1serial_reg);
> + return ret;
> +}
> +
> +static void __exit ma35d1serial_exit(void)
> +{
> + platform_driver_unregister(&ma35d1serial_driver);
> + uart_unregister_driver(&ma35d1serial_reg);
> +}
> +
> +module_init(ma35d1serial_init);
> +module_exit(ma35d1serial_exit);
> +
> +MODULE_LICENSE("GPL v2");
"GPL" is enough for MODULE_LICENSE, the SPDX at the start of file covers
more specific license variations.
> +MODULE_DESCRIPTION("MA35D1 serial driver");
> +MODULE_ALIAS_CHARDEV_MAJOR(TTY_MAJOR);
> +
> diff --git a/drivers/tty/serial/ma35d1_serial.h b/drivers/tty/serial/ma35d1_serial.h
> new file mode 100644
> index 000000000000..5fd845c31b29
> --- /dev/null
> +++ b/drivers/tty/serial/ma35d1_serial.h
> @@ -0,0 +1,93 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * MA35D1 serial driver header file
> + * Copyright (C) 2023 Nuvoton Technology Corp.
> + */
> +#ifndef __MA35D1_SERIAL_H__
> +#define __MA35D1_SERIAL_H__
> +
> +/* UART Receive/Transmit Buffer Register */
> +#define UART_REG_RBR 0x00
> +#define UART_REG_THR 0x00
> +
> +/* UART Interrupt Enable Register */
> +#define UART_REG_IER 0x04
> +#define RDA_IEN 0x00000001 /* RBR Available Interrupt Enable */
> +#define THRE_IEN 0x00000002 /* THR Empty Interrupt Enable */
> +#define RLS_IEN 0x00000004 /* RX Line Status Interrupt Enable */
> +#define RTO_IEN 0x00000010 /* RX Time-out Interrupt Enable */
> +#define BUFERR_IEN 0x00000020 /* Buffer Error Interrupt Enable */
> +#define TIME_OUT_EN 0x00000800 /* RX Buffer Time-out Counter Enable */
> +
> +/* UART FIFO Control Register */
> +#define UART_REG_FCR 0x08
> +#define RFR 0x00000002 /* RX Field Software Reset */
> +#define TFR 0x00000004 /* TX Field Software Reset */
> +
> +/* UART Line Control Register */
> +#define UART_REG_LCR 0x0C
> +#define NSB 0x00000004 /* Number of “STOP Bit” */
> +#define PBE 0x00000008 /* Parity Bit Enable */
> +#define EPE 0x00000010 /* Even Parity Enable */
> +#define SPE 0x00000020 /* Stick Parity Enable */
> +#define BCB 0x00000040 /* Break Control */
> +
> +/* UART Modem Control Register */
> +#define UART_REG_MCR 0x10
> +#define RTS 0x00000020 /* nRTS Signal Control */
> +#define RTSACTLV 0x00000200 /* nRTS Pin Active Level */
> +#define RTSSTS 0x00002000 /* nRTS Pin Status (Read Only) */
> +
> +/* UART Modem Status Register */
> +#define UART_REG_MSR 0x14
> +#define CTSDETF 0x00000001 /* Detect nCTS State Change Flag */
> +#define CTSSTS 0x00000010 /* nCTS Pin Status (Read Only) */
> +#define CTSACTLV 0x00000100 /* nCTS Pin Active Level */
> +
> +/* UART FIFO Status Register */
> +#define UART_REG_FSR 0x18
> +#define RX_OVER_IF 0x00000001 /* RX Overflow Error Interrupt Flag */
> +#define PEF 0x00000010 /* Parity Error Flag*/
> +#define FEF 0x00000020 /* Framing Error Flag */
> +#define BIF 0x00000040 /* Break Interrupt Flag */
> +#define RX_EMPTY 0x00004000 /* Receiver FIFO Empty (Read Only) */
> +#define RX_FULL 0x00008000 /* Receiver FIFO Full (Read Only) */
> +#define TX_EMPTY 0x00400000 /* Transmitter FIFO Empty (Read Only) */
> +#define TX_FULL 0x00800000 /* Transmitter FIFO Full (Read Only) */
> +#define TX_OVER_IF 0x01000000 /* TX Overflow Error Interrupt Flag */
> +#define TE_FLAG 0x10000000 /* Transmitter Empty Flag (Read Only) */
> +
> +/* UART Interrupt Status Register */
> +#define UART_REG_ISR 0x1C
> +#define RDA_IF 0x00000001 /* RBR Available Interrupt Flag */
> +#define THRE_IF 0x00000002 /* THR Empty Interrupt Flag */
> +#define RLSIF 0x00000004 /* Receive Line Interrupt Flag */
> +#define MODEMIF 0x00000008 /* MODEM Interrupt Flag */
> +#define RXTO_IF 0x00000010 /* RX Time-out Interrupt Flag */
> +#define BUFEIF 0x00000020 /* Buffer Error Interrupt Flag */
> +#define WK_IF 0x00000040 /* UART Wake-up Interrupt Flag */
> +#define RDAINT 0x00000100 /* RBR Available Interrupt Indicator */
> +#define THRE_INT 0x00000200 /* THR Empty Interrupt Indicator */
> +
> +/* UART Time-out Register */
> +#define UART_REG_TOR 0x20
> +
> +/* UART Baud Rate Divider Register */
> +#define UART_REG_BAUD 0x24
> +
> +/* UART Alternate Control/Status Register */
> +#define UART_REG_ALT_CSR 0x2C
> +
> +/* UART Function Select Register */
> +#define UART_FUN_SEL 0x30
> +#define FUN_SEL_UART 0x00000000
> +#define FUN_SEL_RS485 0x00000003
> +#define FUN_SEL_MASK 0x00000007
GENMASK(), then use FIELD_PREP() for the values.
> +
> +/* UART Wake-up Control Register */
> +#define UART_REG_WKCTL 0x40
> +
> +/* UART Wake-up Status Register */
> +#define UART_REG_WKSTS 0x44
> +
> +#endif /* __MA35D1_SERIAL_H__ */
> diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
> index 281fa286555c..c6d53db17042 100644
> --- a/include/uapi/linux/serial_core.h
> +++ b/include/uapi/linux/serial_core.h
> @@ -279,4 +279,7 @@
> /* Sunplus UART */
> #define PORT_SUNPLUS 123
>
> +/* Nuvoton MA35D1 UART */
> +#define PORT_MA35D1 124
> +
> #endif /* _UAPILINUX_SERIAL_CORE_H */
>
--
i.
