Structures that come from a device should use __u8 instead of u8
for their elements. Therefore change all elements in the HID report
structs from u8 to __u8.
Signed-off-by: Christina Quast <contact@xxxxxxxxxxxxxxxxxx>
---
drivers/hid/hid-ft260.c | 92 ++++++++++++++++++++---------------------
1 file changed, 46 insertions(+), 46 deletions(-)
diff --git a/drivers/hid/hid-ft260.c b/drivers/hid/hid-ft260.c
index a67051f379a3..c2d1ded4a86b 100644
--- a/drivers/hid/hid-ft260.c
+++ b/drivers/hid/hid-ft260.c
@@ -137,93 +137,93 @@ enum {
/* Feature In reports */
struct ft260_get_chip_version_report {
- u8 report; /* FT260_CHIP_VERSION */
- u8 chip_code[4]; /* FTDI chip identification code */
- u8 reserved[8];
+ __u8 report; /* FT260_CHIP_VERSION */
+ __u8 chip_code[4]; /* FTDI chip identification code */
+ __u8 reserved[8];
} __packed;
struct ft260_get_system_status_report {
- u8 report; /* FT260_SYSTEM_SETTINGS */
- u8 chip_mode; /* DCNF0 and DCNF1 status, bits 0-1 */
- u8 clock_ctl; /* 0 - 12MHz, 1 - 24MHz, 2 - 48MHz */
- u8 suspend_status; /* 0 - not suspended, 1 - suspended */
- u8 pwren_status; /* 0 - FT260 is not ready, 1 - ready */
- u8 i2c_enable; /* 0 - disabled, 1 - enabled */
- u8 uart_mode; /* 0 - OFF; 1 - RTS_CTS, 2 - DTR_DSR, */
+ __u8 report; /* FT260_SYSTEM_SETTINGS */
+ __u8 chip_mode; /* DCNF0 and DCNF1 status, bits 0-1 */
+ __u8 clock_ctl; /* 0 - 12MHz, 1 - 24MHz, 2 - 48MHz */
+ __u8 suspend_status; /* 0 - not suspended, 1 - suspended */
+ __u8 pwren_status; /* 0 - FT260 is not ready, 1 - ready */
+ __u8 i2c_enable; /* 0 - disabled, 1 - enabled */
+ __u8 uart_mode; /* 0 - OFF; 1 - RTS_CTS, 2 - DTR_DSR, */
/* 3 - XON_XOFF, 4 - No flow control */
- u8 hid_over_i2c_en; /* 0 - disabled, 1 - enabled */
- u8 gpio2_function; /* 0 - GPIO, 1 - SUSPOUT, */
+ __u8 hid_over_i2c_en; /* 0 - disabled, 1 - enabled */
+ __u8 gpio2_function; /* 0 - GPIO, 1 - SUSPOUT, */
/* 2 - PWREN, 4 - TX_LED */
- u8 gpioA_function; /* 0 - GPIO, 3 - TX_ACTIVE, 4 - TX_LED */
- u8 gpioG_function; /* 0 - GPIO, 2 - PWREN, */
+ __u8 gpioA_function; /* 0 - GPIO, 3 - TX_ACTIVE, 4 - TX_LED */
+ __u8 gpioG_function; /* 0 - GPIO, 2 - PWREN, */
/* 5 - RX_LED, 6 - BCD_DET */
- u8 suspend_out_pol; /* 0 - active-high, 1 - active-low */
- u8 enable_wakeup_int; /* 0 - disabled, 1 - enabled */
- u8 intr_cond; /* Interrupt trigger conditions */
- u8 power_saving_en; /* 0 - disabled, 1 - enabled */
- u8 reserved[10];
+ __u8 suspend_out_pol; /* 0 - active-high, 1 - active-low */
+ __u8 enable_wakeup_int; /* 0 - disabled, 1 - enabled */
+ __u8 intr_cond; /* Interrupt trigger conditions */
+ __u8 power_saving_en; /* 0 - disabled, 1 - enabled */
+ __u8 reserved[10];
} __packed;
struct ft260_get_i2c_status_report {
- u8 report; /* FT260_I2C_STATUS */
- u8 bus_status; /* I2C bus status */
+ __u8 report; /* FT260_I2C_STATUS */
+ __u8 bus_status; /* I2C bus status */
__le16 clock; /* I2C bus clock in range 60-3400 KHz */
- u8 reserved;
+ __u8 reserved;
} __packed;
/* Feature Out reports */
struct ft260_set_system_clock_report {
- u8 report; /* FT260_SYSTEM_SETTINGS */
- u8 request; /* FT260_SET_CLOCK */
- u8 clock_ctl; /* 0 - 12MHz, 1 - 24MHz, 2 - 48MHz */
+ __u8 report; /* FT260_SYSTEM_SETTINGS */
+ __u8 request; /* FT260_SET_CLOCK */
+ __u8 clock_ctl; /* 0 - 12MHz, 1 - 24MHz, 2 - 48MHz */
} __packed;
struct ft260_set_i2c_mode_report {
- u8 report; /* FT260_SYSTEM_SETTINGS */
- u8 request; /* FT260_SET_I2C_MODE */
- u8 i2c_enable; /* 0 - disabled, 1 - enabled */
+ __u8 report; /* FT260_SYSTEM_SETTINGS */
+ __u8 request; /* FT260_SET_I2C_MODE */
+ __u8 i2c_enable; /* 0 - disabled, 1 - enabled */
} __packed;
struct ft260_set_uart_mode_report {
- u8 report; /* FT260_SYSTEM_SETTINGS */
- u8 request; /* FT260_SET_UART_MODE */
- u8 uart_mode; /* 0 - OFF; 1 - RTS_CTS, 2 - DTR_DSR, */
+ __u8 report; /* FT260_SYSTEM_SETTINGS */
+ __u8 request; /* FT260_SET_UART_MODE */
+ __u8 uart_mode; /* 0 - OFF; 1 - RTS_CTS, 2 - DTR_DSR, */
/* 3 - XON_XOFF, 4 - No flow control */
} __packed;
struct ft260_set_i2c_reset_report {
- u8 report; /* FT260_SYSTEM_SETTINGS */
- u8 request; /* FT260_SET_I2C_RESET */
+ __u8 report; /* FT260_SYSTEM_SETTINGS */
+ __u8 request; /* FT260_SET_I2C_RESET */
} __packed;
struct ft260_set_i2c_speed_report {
- u8 report; /* FT260_SYSTEM_SETTINGS */
- u8 request; /* FT260_SET_I2C_CLOCK_SPEED */
+ __u8 report; /* FT260_SYSTEM_SETTINGS */
+ __u8 request; /* FT260_SET_I2C_CLOCK_SPEED */
__le16 clock; /* I2C bus clock in range 60-3400 KHz */
} __packed;
/* Data transfer reports */
struct ft260_i2c_write_request_report {
- u8 report; /* FT260_I2C_REPORT */
- u8 address; /* 7-bit I2C address */
- u8 flag; /* I2C transaction condition */
- u8 length; /* data payload length */
- u8 data[FT260_WR_DATA_MAX]; /* data payload */
+ __u8 report; /* FT260_I2C_REPORT */
+ __u8 address; /* 7-bit I2C address */
+ __u8 flag; /* I2C transaction condition */
+ __u8 length; /* data payload length */
+ __u8 data[FT260_WR_DATA_MAX]; /* data payload */
} __packed;
struct ft260_i2c_read_request_report {
- u8 report; /* FT260_I2C_READ_REQ */
- u8 address; /* 7-bit I2C address */
- u8 flag; /* I2C transaction condition */
+ __u8 report; /* FT260_I2C_READ_REQ */
+ __u8 address; /* 7-bit I2C address */
+ __u8 flag; /* I2C transaction condition */
__le16 length; /* data payload length */
} __packed;
struct ft260_input_report {
- u8 report; /* FT260_I2C_REPORT or FT260_UART_REPORT */
- u8 length; /* data payload length */
- u8 data[2]; /* data payload */
+ __u8 report; /* FT260_I2C_REPORT or FT260_UART_REPORT */
+ __u8 length; /* data payload length */
+ __u8 data[2]; /* data payload */
} __packed;
static const struct hid_device_id ft260_devices[] = {
--
2.35.1
