pci1xxxx uart supports rs485 mode of operation in the hardware with
auto-direction control with configurable delay for releasing RTS after
the transmission. This patch adds support for the rs485 mode.
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@xxxxxxxxxxxxx>
---
Changes in v2:
- move pci1xxxx_rs485_config to a separate patch with
pci1xxxx_rs485_supported.
---
drivers/tty/serial/8250/8250_pci1xxxx.c | 57 +++++++++++++++++++++++++
1 file changed, 57 insertions(+)
diff --git a/drivers/tty/serial/8250/8250_pci1xxxx.c b/drivers/tty/serial/8250/8250_pci1xxxx.c
index 41a4b94f52b4..999e5a284266 100644
--- a/drivers/tty/serial/8250/8250_pci1xxxx.c
+++ b/drivers/tty/serial/8250/8250_pci1xxxx.c
@@ -137,6 +137,61 @@ static void pci1xxxx_set_divisor(struct uart_port *port, unsigned int baud,
writel((quot << 8) | frac, (port->membase + CLK_DIVISOR_REG));
}
+static const struct serial_rs485 pci1xxxx_rs485_supported = {
+ .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND,
+ .delay_rts_after_send = 1,
+ /* Delay RTS before send is not supported */
+};
+
+static int pci1xxxx_rs485_config(struct uart_port *port,
+ struct ktermios *termios,
+ struct serial_rs485 *rs485)
+{
+ u32 clock_div = readl(port->membase + CLK_DIVISOR_REG);
+ u8 delay_in_baud_periods = 0;
+ u32 baud_period_in_ns = 0;
+ u8 data = 0;
+
+ /* pci1xxxx's uart hardware supports only RTS delay after
+ * Tx and in units of bit times to a maximum of 15
+ */
+
+ rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+ SER_RS485_RTS_AFTER_SEND;
+
+ if (rs485->flags & SER_RS485_ENABLED) {
+ memset(rs485->padding, 0, sizeof(rs485->padding));
+
+ data = ADCL_CFG_EN | ADCL_CFG_PIN_SEL;
+
+ if (!(rs485->flags & SER_RS485_RTS_ON_SEND)) {
+ data |= ADCL_CFG_POL_SEL;
+ rs485->flags |= SER_RS485_RTS_AFTER_SEND;
+ } else {
+ rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
+ }
+
+ if (rs485->delay_rts_after_send) {
+ baud_period_in_ns = ((clock_div >> 8) * 16);
+ delay_in_baud_periods = (rs485->delay_rts_after_send * 1000000) /
+ baud_period_in_ns;
+ if (delay_in_baud_periods > 0xF)
+ delay_in_baud_periods = 0xF;
+ data |= delay_in_baud_periods << 8;
+ rs485->delay_rts_after_send = (baud_period_in_ns * delay_in_baud_periods) /
+ 1000000;
+ rs485->delay_rts_before_send = 0;
+ }
+ } else {
+ memset(rs485, 0, sizeof(*rs485));
+ }
+
+ writeb(data, (port->membase + ADCL_CFG_REG));
+ port->rs485 = *rs485;
+
+ return 0;
+}
+
static int pci1xxxx_get_num_ports(struct pci_dev *dev)
{
int nr_ports = 1;
@@ -217,6 +272,8 @@ static int pci1xxxx_setup(struct pci1xxxx_8250 *priv,
port->port.set_termios = serial8250_do_set_termios;
port->port.get_divisor = pci1xxxx_get_divisor;
port->port.set_divisor = pci1xxxx_set_divisor;
+ port->port.rs485_config = pci1xxxx_rs485_config;
+ port->port.rs485_supported = pci1xxxx_rs485_supported;
ret = pci1xxxx_setup_port(priv, port, offset);
if (ret < 0)
return ret;
--
2.25.1
