Make sure that the driver only divides the clock divisor if the
IP handled at that point is USART, since UART IP's do not support
implicit peripheral clock division. Instead, in the case of UART,
go with the highest possible clock divisor.
Signed-off-by: Sergiu Moga <sergiu.moga@xxxxxxxxxxxxx>
---
v1 -> v2:
- Nothing, this patch was not here before and is mainly meant as both cleanup
and as a way to introduce a new field into struct atmel_uart_port that will be
used by the last patch to diferentiate between USART and UART regarding the
location of the Baudrate Clock Source bitmask.
drivers/tty/serial/atmel_serial.c | 13 ++++++++++++-
1 file changed, 12 insertions(+), 1 deletion(-)
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 7450d3853031..6aa01ca5489c 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -150,6 +150,7 @@ struct atmel_uart_port {
u32 rts_low;
bool ms_irq_enabled;
u32 rtor; /* address of receiver timeout register if it exists */
+ bool is_usart;
bool has_frac_baudrate;
bool has_hw_timer;
struct timer_list uart_timer;
@@ -1825,6 +1826,7 @@ static void atmel_get_ip_name(struct uart_port *port)
*/
atmel_port->has_frac_baudrate = false;
atmel_port->has_hw_timer = false;
+ atmel_port->is_usart = false;
if (name == new_uart) {
dev_dbg(port->dev, "Uart with hw timer");
@@ -1834,6 +1836,7 @@ static void atmel_get_ip_name(struct uart_port *port)
dev_dbg(port->dev, "Usart\n");
atmel_port->has_frac_baudrate = true;
atmel_port->has_hw_timer = true;
+ atmel_port->is_usart = true;
atmel_port->rtor = ATMEL_US_RTOR;
version = atmel_uart_readl(port, ATMEL_US_VERSION);
switch (version) {
@@ -1863,6 +1866,7 @@ static void atmel_get_ip_name(struct uart_port *port)
dev_dbg(port->dev, "This version is usart\n");
atmel_port->has_frac_baudrate = true;
atmel_port->has_hw_timer = true;
+ atmel_port->is_usart = true;
atmel_port->rtor = ATMEL_US_RTOR;
break;
case 0x203:
@@ -2282,10 +2286,17 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
cd = uart_get_divisor(port, baud);
}
- if (cd > 65535) { /* BRGR is 16-bit, so switch to slower clock */
+ /*
+ * BRGR is 16-bit, so switch to slower clock.
+ * Otherwise, keep the highest possible value for the clock divisor.
+ */
+ if (atmel_port->is_usart && cd > 65535) {
cd /= 8;
mode |= ATMEL_US_USCLKS_MCK_DIV8;
+ } else {
+ cd &= 65535;
}
+
quot = cd | fp << ATMEL_US_FP_OFFSET;
if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
--
2.25.1
