The number of bits can be calculated using tty_get_frame_size(), no
need for the driver to do it on its own.
Also remove a comment on number of bits that doesn't match the code nor
the comment on ucc_uart_pram's rx_length ("minus 1" part differs). That
comment seems a verbatim copy of that in cpm_uart/cpm_uart_core.c
anyway so perhaps it was just copied over w/o much thinking.
Reviewed-by: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@xxxxxxxxxxxxxxx>
---
drivers/tty/serial/ucc_uart.c | 15 +--------------
1 file changed, 1 insertion(+), 14 deletions(-)
diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 3cc9ef08455c..7331964163c5 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -853,13 +853,6 @@ static void qe_uart_set_termios(struct uart_port *port,
u16 upsmr = ioread16be(&uccp->upsmr);
struct ucc_uart_pram __iomem *uccup = qe_port->uccup;
u16 supsmr = ioread16be(&uccup->supsmr);
- u8 char_length = 2; /* 1 + CL + PEN + 1 + SL */
-
- /* Character length programmed into the mode register is the
- * sum of: 1 start bit, number of data bits, 0 or 1 parity bit,
- * 1 or 2 stop bits, minus 1.
- * The value 'bits' counts this for us.
- */
/* byte size */
upsmr &= UCC_UART_UPSMR_CL_MASK;
@@ -869,22 +862,18 @@ static void qe_uart_set_termios(struct uart_port *port,
case CS5:
upsmr |= UCC_UART_UPSMR_CL_5;
supsmr |= UCC_UART_SUPSMR_CL_5;
- char_length += 5;
break;
case CS6:
upsmr |= UCC_UART_UPSMR_CL_6;
supsmr |= UCC_UART_SUPSMR_CL_6;
- char_length += 6;
break;
case CS7:
upsmr |= UCC_UART_UPSMR_CL_7;
supsmr |= UCC_UART_SUPSMR_CL_7;
- char_length += 7;
break;
default: /* case CS8 */
upsmr |= UCC_UART_UPSMR_CL_8;
supsmr |= UCC_UART_SUPSMR_CL_8;
- char_length += 8;
break;
}
@@ -892,13 +881,11 @@ static void qe_uart_set_termios(struct uart_port *port,
if (termios->c_cflag & CSTOPB) {
upsmr |= UCC_UART_UPSMR_SL;
supsmr |= UCC_UART_SUPSMR_SL;
- char_length++; /* + SL */
}
if (termios->c_cflag & PARENB) {
upsmr |= UCC_UART_UPSMR_PEN;
supsmr |= UCC_UART_SUPSMR_PEN;
- char_length++; /* + PEN */
if (!(termios->c_cflag & PARODD)) {
upsmr &= ~(UCC_UART_UPSMR_RPM_MASK |
@@ -953,7 +940,7 @@ static void qe_uart_set_termios(struct uart_port *port,
iowrite16be(upsmr, &uccp->upsmr);
if (soft_uart) {
iowrite16be(supsmr, &uccup->supsmr);
- iowrite8(char_length, &uccup->rx_length);
+ iowrite8(tty_get_frame_size(termios->c_cflag), &uccup->rx_length);
/* Soft-UART requires a 1X multiplier for TX */
qe_setbrg(qe_port->us_info.rx_clock, baud, 16);
--
2.30.2
