Convert struct serial_rs485 comments to kernel doc format. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@xxxxxxxxxxxxxxx> --- include/uapi/linux/serial.h | 61 ++++++++++++++++++++++++------------- 1 file changed, 40 insertions(+), 21 deletions(-) diff --git a/include/uapi/linux/serial.h b/include/uapi/linux/serial.h index cea06924b295..dbdc7865abdc 100644 --- a/include/uapi/linux/serial.h +++ b/include/uapi/linux/serial.h @@ -107,37 +107,56 @@ struct serial_icounter_struct { int reserved[9]; }; -/* +/** + * struct serial_rs485 - serial interface for controlling RS485 settings. + * @flags: RS485 feature flags + * @delay_rts_before_send: Delay before send (milliseconds) + * @delay_rts_after_send: Delay after send (milliseconds) + * @addr_recv: Receive filter for RS485 addressing mode + * (used only when %SER_RS485_ADDR_RECV is set). + * @addr_dest: Destination address for RS485 addressing mode + * (used only when %SER_RS485_ADDR_DEST is set). + * @padding0: Padding (set to zero). + * @padding1: Padding (set to zero). + * @padding: Deprecated, use @padding0 and @padding1 instead. + * Do not use with @addr_recv and @addr_dest (due to + * overlap). + * * Serial interface for controlling RS485 settings on chips with suitable * support. Set with TIOCSRS485 and get with TIOCGRS485 if supported by your * platform. The set function returns the new state, with any unsupported bits * reverted appropriately. + * + * serial_rs485::flags bits are: + * * %SER_RS485_ENABLED - RS485 enabled + * * %SER_RS485_RTS_ON_SEND - Logical level for RTS pin when sending + * * %SER_RS485_RTS_AFTER_SEND - Logical level for RTS pin after sent + * * %SER_RS485_RX_DURING_TX - Full-duplex RS485 line + * * %SER_RS485_TERMINATE_BUS - Enable bus termination (if supported) + * * %SER_RS485_ADDRB - Enable RS485 addressing mode + * * %SER_RS485_ADDR_RECV - Receive address filter (enables @addr_recv). + * Requires %SER_RS485_ADDRB. + * * %SER_RS485_ADDR_DEST - Destination address (enables @addr_dest). + * Requires %SER_RS485_ADDRB. */ - struct serial_rs485 { - __u32 flags; /* RS485 feature flags */ -#define SER_RS485_ENABLED (1 << 0) /* If enabled */ -#define SER_RS485_RTS_ON_SEND (1 << 1) /* Logical level for - RTS pin when - sending */ -#define SER_RS485_RTS_AFTER_SEND (1 << 2) /* Logical level for - RTS pin after sent*/ + __u32 flags; +#define SER_RS485_ENABLED (1 << 0) +#define SER_RS485_RTS_ON_SEND (1 << 1) +#define SER_RS485_RTS_AFTER_SEND (1 << 2) #define SER_RS485_RX_DURING_TX (1 << 4) -#define SER_RS485_TERMINATE_BUS (1 << 5) /* Enable bus - termination - (if supported) */ - -/* RS-485 addressing mode */ -#define SER_RS485_ADDRB (1 << 6) /* Enable addressing mode */ -#define SER_RS485_ADDR_RECV (1 << 7) /* Receive address filter */ -#define SER_RS485_ADDR_DEST (1 << 8) /* Destination address */ +#define SER_RS485_TERMINATE_BUS (1 << 5) +#define SER_RS485_ADDRB (1 << 6) +#define SER_RS485_ADDR_RECV (1 << 7) +#define SER_RS485_ADDR_DEST (1 << 8) - __u32 delay_rts_before_send; /* Delay before send (milliseconds) */ - __u32 delay_rts_after_send; /* Delay after send (milliseconds) */ + __u32 delay_rts_before_send; + __u32 delay_rts_after_send; - /* The fields below are defined by flags */ + /* private: The fields below are defined by flags */ union { - __u32 padding[5]; /* Memory is cheap, new structs are a pain */ + /* private: Memory is cheap, new structs are a pain. */ + __u32 padding[5]; struct { __u8 addr_recv; -- 2.30.2