Am 23.11.2021 um 13:19 schrieb Michal Simek:
On 11/22/21 23:08, Ruediger Willenberg wrote:
Am 19.11.2021 um 13:21 schrieb Michal Simek:
On 11/18/21 22:17, Ruediger Willenberg wrote:
Find free uart_port struct in range 0 <= id < ULITE_NR_UARTS when
the device tree port-number property is outside that range. This
happens when there are other UART types in the system because the
Xilinx device tree generator numbers all UARTs consecutively;
as a result, not as many Uartlites as specified by the
SERIAL_UARTLITE_NR_UARTS parameter could be successfully added.
Signed-off-by: Ruediger Willenberg <r.willenberg@xxxxxxxxxxxxxx>
---
Changes in v2:
- give KERN_NOTICE when changing the id,
with reference to the requested port-number
- if (id < 0 || id >= ULITE_NR_UARTS) {
- dev_err(dev, "%s%i too large\n", ULITE_NAME, id);
+ if (id == ULITE_NR_UARTS) {
+ dev_err(dev, "maximum number of %s assigned\n", ULITE_NAME);
return -EINVAL;
}
@@ -676,7 +678,11 @@ static int ulite_assign(struct device *dev, int
id, u32 base, int irq,
dev_set_drvdata(dev, NULL);
return rc;
}
nit: please keep this newline here.
-
+ if (oor_id >= 0)
+ dev_notice(dev,
+ "assigned uartlite with device tree port-number=<%i> to
%s%i\n",
+ oor_id, ULITE_NAME, id);
+
[linux](master)$ ./scripts/checkpatch.pl --strict
0001-serial-uartlite-Move-out-of-range-port-numbers-into-.patch
CHECK: Alignment should match open parenthesis
Thanks, I apparently didn't do "--strict" checking, sorry. Will fix
both in PATCH v3
And there is one more issue with this. If you start to mix serial IPs
which are partially recorded in aliases. For example like this.
aliases {
serial0 = &uart1;
};
uart0 {
...
};
Uart0 is probed first. It is without alias and id 0 will be assigned
to it. Then uart1 is probed. It looks at aliases you get id 0 but it
is already taken and you end up with "cannot assign to %s%i; it is
already in use"
As I point out in the other thread
"[PATCH v2] uartlite: Update the default for the
SERIAL_UARTLITE_NR_UARTS"
(I don't feel crossposting all of it here would be good practice)
a) the Xilinx DTG gives "serial" aliases to _all_ Xilinx UARTs
b) the Xilinx DTG gives "port-number" properties to _all_ Xilinx UARTs
c) these two are not assigned in the same order by the Xilinx DTG,
which is problematic
DTG/MSS logic should be solved in different mailing list that's why
please move it there.
I agree in principle. Michal, since you have an @xilinx.com domain could
you please share where that place to discuss is?
The Linux "devicetree" list doesn't not seem the right place either for
a company-managed, separate repo. If this goes your suggested way
(completely changing the uartlite driver to use the "serial" alias, the
Xilinx DTG _needs_ to be improved, including respecting the serial0
alias for the designated console. I'd be glad to contribute to the
discussion there. Right not there's a mess that's not solved by throwing
out the port-number property alone.
uartlite.c currently looks at port-number properties, not aliases. So
unassigned aliases are not the issue. A similar-looking but more
complicated issue that COULD happen, to be transparent, is this:
port-number is optional and as I said in the second thread I think that
this should be deprecated and removed. Most of DT drivers take care
about serial alias that's why we should go that route too.
And I also remember that drivers shouldn't really use different names as
ttyUL, ttyPS, ttyAMA, etc but all of them should use the same name as
ttyUSB is doing.
Big improvements are good and well, but they tend to break things and
again it does mean the Xilinx DTG needs to move with that.
I'd be immensely grateful if you could indicate _where_ to discuss those
changes, and who has the authority to speak for Xilinx. Off-list, if you
think that is more appropriate.
Thank you,
Ruediger
