We want to remove the use of pm_runtime_irq_safe() from serial drivers
to allow making PM runtime handling generic. Let's simplify things by
disabling PM runtime autoidle for omap-serial as this driver has been
deprecated for years because of the 8250_omap driver.
There are still some omap-serial users that seem to hang on to it for
some unknown rs485 reasons it seems. But presumably those folks do not
need PM runtime autoidle with omap-serial, and hopefully can just move
to using 8250_omap driver instead.
For 8250_omap driver, we will eventually move to use generic serial
layer PM based on patches done by Andy Shevchenko to remove
pm_runtime_irq_safe() usage.
Cc: Andy Shevchenko <andriy.shevchenko@xxxxxxxxx>
Cc: Dario Binacchi <dariobin@xxxxxxxxx>
Cc: Vignesh Raghavendra <vigneshr@xxxxxx>
Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
---
drivers/tty/serial/omap-serial.c | 75 +-------------------------------
1 file changed, 2 insertions(+), 73 deletions(-)
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -276,11 +276,8 @@ static void serial_omap_enable_ms(struct uart_port *port)
dev_dbg(up->port.dev, "serial_omap_enable_ms+%d\n", up->port.line);
- pm_runtime_get_sync(up->dev);
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
}
static void serial_omap_stop_tx(struct uart_port *port)
@@ -288,8 +285,6 @@ static void serial_omap_stop_tx(struct uart_port *port)
struct uart_omap_port *up = to_uart_omap_port(port);
int res;
- pm_runtime_get_sync(up->dev);
-
/* Handle RS-485 */
if (port->rs485.flags & SER_RS485_ENABLED) {
if (up->scr & OMAP_UART_SCR_TX_EMPTY) {
@@ -330,21 +325,15 @@ static void serial_omap_stop_tx(struct uart_port *port)
up->ier &= ~UART_IER_THRI;
serial_out(up, UART_IER, up->ier);
}
-
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
}
static void serial_omap_stop_rx(struct uart_port *port)
{
struct uart_omap_port *up = to_uart_omap_port(port);
- pm_runtime_get_sync(up->dev);
up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
up->port.read_status_mask &= ~UART_LSR_DR;
serial_out(up, UART_IER, up->ier);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
}
static void transmit_chars(struct uart_omap_port *up, unsigned int lsr)
@@ -399,8 +388,6 @@ static void serial_omap_start_tx(struct uart_port *port)
struct uart_omap_port *up = to_uart_omap_port(port);
int res;
- pm_runtime_get_sync(up->dev);
-
/* Handle RS-485 */
if (port->rs485.flags & SER_RS485_ENABLED) {
/* Fire THR interrupts when FIFO is below trigger level */
@@ -421,8 +408,6 @@ static void serial_omap_start_tx(struct uart_port *port)
up->rs485_tx_filter_count = 0;
serial_omap_enable_ier_thri(up);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
}
static void serial_omap_throttle(struct uart_port *port)
@@ -430,13 +415,10 @@ static void serial_omap_throttle(struct uart_port *port)
struct uart_omap_port *up = to_uart_omap_port(port);
unsigned long flags;
- pm_runtime_get_sync(up->dev);
spin_lock_irqsave(&up->port.lock, flags);
up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
serial_out(up, UART_IER, up->ier);
spin_unlock_irqrestore(&up->port.lock, flags);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
}
static void serial_omap_unthrottle(struct uart_port *port)
@@ -444,13 +426,10 @@ static void serial_omap_unthrottle(struct uart_port *port)
struct uart_omap_port *up = to_uart_omap_port(port);
unsigned long flags;
- pm_runtime_get_sync(up->dev);
spin_lock_irqsave(&up->port.lock, flags);
up->ier |= UART_IER_RLSI | UART_IER_RDI;
serial_out(up, UART_IER, up->ier);
spin_unlock_irqrestore(&up->port.lock, flags);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
}
static unsigned int check_modem_status(struct uart_omap_port *up)
@@ -576,7 +555,6 @@ static irqreturn_t serial_omap_irq(int irq, void *dev_id)
int max_count = 256;
spin_lock(&up->port.lock);
- pm_runtime_get_sync(up->dev);
do {
iir = serial_in(up, UART_IIR);
@@ -616,8 +594,6 @@ static irqreturn_t serial_omap_irq(int irq, void *dev_id)
tty_flip_buffer_push(&up->port.state->port);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
up->port_activity = jiffies;
return ret;
@@ -629,13 +605,11 @@ static unsigned int serial_omap_tx_empty(struct uart_port *port)
unsigned long flags;
unsigned int ret = 0;
- pm_runtime_get_sync(up->dev);
dev_dbg(up->port.dev, "serial_omap_tx_empty+%d\n", up->port.line);
spin_lock_irqsave(&up->port.lock, flags);
ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
spin_unlock_irqrestore(&up->port.lock, flags);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
+
return ret;
}
@@ -645,10 +619,7 @@ static unsigned int serial_omap_get_mctrl(struct uart_port *port)
unsigned int status;
unsigned int ret = 0;
- pm_runtime_get_sync(up->dev);
status = check_modem_status(up);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
dev_dbg(up->port.dev, "serial_omap_get_mctrl+%d\n", up->port.line);
@@ -680,7 +651,6 @@ static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
if (mctrl & TIOCM_LOOP)
mcr |= UART_MCR_LOOP;
- pm_runtime_get_sync(up->dev);
old_mcr = serial_in(up, UART_MCR);
old_mcr &= ~(UART_MCR_LOOP | UART_MCR_OUT2 | UART_MCR_OUT1 |
UART_MCR_DTR | UART_MCR_RTS);
@@ -696,9 +666,6 @@ static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
up->efr &= ~UART_EFR_RTS;
serial_out(up, UART_EFR, up->efr);
serial_out(up, UART_LCR, lcr);
-
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
}
static void serial_omap_break_ctl(struct uart_port *port, int break_state)
@@ -707,7 +674,6 @@ static void serial_omap_break_ctl(struct uart_port *port, int break_state)
unsigned long flags;
dev_dbg(up->port.dev, "serial_omap_break_ctl+%d\n", up->port.line);
- pm_runtime_get_sync(up->dev);
spin_lock_irqsave(&up->port.lock, flags);
if (break_state == -1)
up->lcr |= UART_LCR_SBC;
@@ -715,8 +681,6 @@ static void serial_omap_break_ctl(struct uart_port *port, int break_state)
up->lcr &= ~UART_LCR_SBC;
serial_out(up, UART_LCR, up->lcr);
spin_unlock_irqrestore(&up->port.lock, flags);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
}
static int serial_omap_startup(struct uart_port *port)
@@ -788,8 +752,6 @@ static int serial_omap_startup(struct uart_port *port)
serial_out(up, UART_OMAP_WER, up->wer);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
up->port_activity = jiffies;
return 0;
}
@@ -801,7 +763,6 @@ static void serial_omap_shutdown(struct uart_port *port)
dev_dbg(up->port.dev, "serial_omap_shutdown+%d\n", up->port.line);
- pm_runtime_get_sync(up->dev);
/*
* Disable interrupts from this port
*/
@@ -825,8 +786,7 @@ static void serial_omap_shutdown(struct uart_port *port)
if (serial_in(up, UART_LSR) & UART_LSR_DR)
(void) serial_in(up, UART_RX);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
+ pm_runtime_put_sync(up->dev);
free_irq(up->port.irq, up);
dev_pm_clear_wake_irq(up->dev);
}
@@ -896,7 +856,6 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
- pm_runtime_get_sync(up->dev);
spin_lock_irqsave(&up->port.lock, flags);
/*
@@ -1096,8 +1055,6 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
serial_omap_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->port.line);
}
@@ -1110,7 +1067,6 @@ serial_omap_pm(struct uart_port *port, unsigned int state,
dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->port.line);
- pm_runtime_get_sync(up->dev);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, efr | UART_EFR_ECB);
@@ -1120,9 +1076,6 @@ serial_omap_pm(struct uart_port *port, unsigned int state,
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_EFR, efr);
serial_out(up, UART_LCR, 0);
-
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
}
static void serial_omap_release_port(struct uart_port *port)
@@ -1202,11 +1155,8 @@ static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
{
struct uart_omap_port *up = to_uart_omap_port(port);
- pm_runtime_get_sync(up->dev);
wait_for_xmitr(up);
serial_out(up, UART_TX, ch);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
}
static int serial_omap_poll_get_char(struct uart_port *port)
@@ -1214,7 +1164,6 @@ static int serial_omap_poll_get_char(struct uart_port *port)
struct uart_omap_port *up = to_uart_omap_port(port);
unsigned int status;
- pm_runtime_get_sync(up->dev);
status = serial_in(up, UART_LSR);
if (!(status & UART_LSR_DR)) {
status = NO_POLL_CHAR;
@@ -1224,9 +1173,6 @@ static int serial_omap_poll_get_char(struct uart_port *port)
status = serial_in(up, UART_RX);
out:
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
-
return status;
}
@@ -1309,8 +1255,6 @@ serial_omap_console_write(struct console *co, const char *s,
unsigned int ier;
int locked = 1;
- pm_runtime_get_sync(up->dev);
-
local_irq_save(flags);
if (up->port.sysrq)
locked = 0;
@@ -1343,8 +1287,6 @@ serial_omap_console_write(struct console *co, const char *s,
if (up->msr_saved_flags)
check_modem_status(up);
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
if (locked)
spin_unlock(&up->port.lock);
local_irq_restore(flags);
@@ -1403,8 +1345,6 @@ serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
unsigned int mode;
int val;
- pm_runtime_get_sync(up->dev);
-
/* Disable interrupts from this port */
mode = up->ier;
up->ier = 0;
@@ -1438,9 +1378,6 @@ serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
serial_out(up, UART_OMAP_SCR, up->scr);
}
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
-
return 0;
}
@@ -1737,11 +1674,7 @@ static int serial_omap_probe(struct platform_device *pdev)
omap_up_info->autosuspend_timeout = -1;
device_init_wakeup(up->dev, true);
- pm_runtime_use_autosuspend(&pdev->dev);
- pm_runtime_set_autosuspend_delay(&pdev->dev,
- omap_up_info->autosuspend_timeout);
- pm_runtime_irq_safe(&pdev->dev);
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
@@ -1755,12 +1688,9 @@ static int serial_omap_probe(struct platform_device *pdev)
if (ret != 0)
goto err_add_port;
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
return 0;
err_add_port:
- pm_runtime_dont_use_autosuspend(&pdev->dev);
pm_runtime_put_sync(&pdev->dev);
pm_runtime_disable(&pdev->dev);
cpu_latency_qos_remove_request(&up->pm_qos_request);
@@ -1778,7 +1708,6 @@ static int serial_omap_remove(struct platform_device *dev)
uart_remove_one_port(&serial_omap_reg, &up->port);
- pm_runtime_dont_use_autosuspend(up->dev);
pm_runtime_put_sync(up->dev);
pm_runtime_disable(up->dev);
cpu_latency_qos_remove_request(&up->pm_qos_request);
--
2.32.0
