Hi,
On Tue, Aug 11, 2020 at 4:54 AM Akash Asthana <akashast@xxxxxxxxxxxxxx> wrote:
>
>
> On 8/11/2020 2:56 AM, Doug Anderson wrote:
> > Hi,
> >
> > On Mon, Aug 10, 2020 at 5:32 AM Akash Asthana <akashast@xxxxxxxxxxxxxx> wrote:
> >> Hi Doug,
> >>
> >> On 8/7/2020 10:49 AM, Douglas Anderson wrote:
> >>> The commit e42d6c3ec0c7 ("serial: qcom_geni_serial: Make kgdb work
> >>> even if UART isn't console") worked pretty well and I've been doing a
> >>> lot of debugging with it. However, recently I typed "dmesg" in kdb
> >>> and then held the space key down to scroll through the pagination. My
> >>> device hung. This was repeatable and I found that it was introduced
> >>> with the aforementioned commit.
> >>>
> >>> It turns out that there are some strange boundary cases in geni where
> >>> in some weird situations it will signal RX_LAST but then will put 0 in
> >>> RX_LAST_BYTE. This means that the entire last FIFO entry is valid.
> >> IMO that means we received a word in RX_FIFO and it is the last word
> >> hence RX_LAST bit is set.
> > What you say would make logical sense, but it's not how I have
> > observed geni to work. See below.
> >
> >
> >> RX_LAST_BYTE is 0 means none of the bytes are valid in the last word.
> > This would imply that qcom_geni_serial_handle_rx() is also broken
> > though, wouldn't it? Specifically imagine that WORD_CNT is 1 and
> > RX_LAST is set and RX_LAST_BYTE_VALID is true. Here's the logic from
> > that function:
> >
> > total_bytes = BYTES_PER_FIFO_WORD * (word_cnt - 1);
> > if (last_word_partial && last_word_byte_cnt)
> > total_bytes += last_word_byte_cnt;
> > else
> > total_bytes += BYTES_PER_FIFO_WORD;
> > port->handle_rx(uport, total_bytes, drop);
> >
> > As you can see that logic will set "total_bytes" to 4 in the case I'm
> > talking about.
>
> Yeah IMO as per theory this should also be corrected but since you have
> already pulled out few experiment to prove garbage data issue(which I
> was suspecting) is not seen.
>
> It's already consistent with existing logic and it behaves well
> practically . So the changes could be merge. Meanwhile I am checking
> with HW team to get clarity.
>
> >
> >
> >> In such scenario we should just read RX_FIFO buffer (to empty it),
> >> discard the word and return NO_POLL_CHAR. Something like below.
> >>
> >> ---------------------------------------------------------------------------------------------------------------------------------------------------------
> >>
> >> else
> >> private_data->poll_cached_bytes_cnt = 4;
> >>
> >> private_data->poll_cached_bytes =
> >> readl(uport->membase + SE_GENI_RX_FIFOn);
> >> }
> >>
> >> + if (!private_data->poll_cached_bytes_cnt)
> >> + return NO_POLL_CHAR;
> >> private_data->poll_cached_bytes_cnt--;
> >> ret = private_data->poll_cached_bytes & 0xff;
> >> -------------------------------------------------------------------------------------------------------------------------------------------------------------
> >>
> >> Please let me know whether above code helps.
> > Your code will avoid the hang. Yes. ...but it will drop bytes. I
> > devised a quick-n-dirty test. Here's a test of your code:
> I assumed those as invalid bytes and don't wanted to read them so yeah
> dropping of bytes was expected.
> >
> > https://crrev.com/c/2346886
> >
> > ...and here's a test of my code:
> >
> > https://crrev.com/c/2346884
> >
> > I had to keep a buffer around since it's hard to debug the serial
> > driver. In both cases I put "DOUG" into the buffer when I detect this
> > case. If my theory about how geni worked was wrong then we should
> > expect to see some garbage in the buffer right after the DOUG, right?
> > ...but my code gets the alphabet in nice sequence. Your code drops 4
> > bytes.
> Yeah I was expecting garbage data.
> >
> >
> > NOTE: while poking around with the above two test patches I found it
> > was pretty easy to get geni to drop bytes / hit overflow cases and
> > also to insert bogus 0 bytes in the stream (I believe these are
> > related). I was able to reproduce this:
> > * With ${SUBJECT} patch in place.
> > * With your proposed patch.
> > * With the recent "geni" patches reverted (in other words back to 1
> > byte per FIFO entry).
> >
> > It's not terribly surprising that we're overflowing since I believe
> > kgdb isn't too keen to read characters at the same time it's writing.
> > That doesn't explain the weird 0-bytes that geni seemed to be
> > inserting, but at least it would explain the overflows. However, even
> > after I fixed this I _still_ was getting problems. Specifically geni
> > seemed to be hiding bytes from me until it was too late. I put
> > logging in and would see this:
> >
> > 1 word in FIFO - wxyz
> > 1 word in FIFO (last set, last FIFO has 1 byte) - \n
> > Check again, still 0 bytes in FIFO
> > Suddenly 16 bytes are in FIFO and S_RX_FIFO_WR_ERR_EN is set.
>
> RX data first stored in RX_ASYNC_FIFO then it's transfered to RX_FIFO
>
> When get_char is called and we observe 0 bytes in RX_FIFO, most probably
> data is not transfered from RX_ASYNC_FIFO to RX_FIFO.
>
> BITS 27:25 of SE_GENI_RX_FIFO_STATUS register shows RX_ASYNC_FIFO word
> count.
OK, I did a tad bit more debugging and I think any problems left after
my patch are actually kdb's fault, though geni doesn't behave terribly
well with overflows (it would be better if it just dropped characters
rather than enqueuing garbage). Specifically in the tests I was
running recently kdb would sometimes still take over 30 ms between
polls so it's not surprising that we'd get overflows if we're
spamming. All my test code and results are at:
https://crrev.com/c/2348284
Earlier when I claimed that bytes were showing up in geni too quickly
I was wrong. My timing code was broken at the time.
> > I spent a whole bunch of time poking at this and couldn't find any
> > sort of workaround. Presumably geni is taking some time between me
> > reading the last word out of the FIFO from the "previous" packet and
> > then transitioning to the new packet. I found a lot of references to
> > this process in the hardware register description (see GENI_CFG_REG69,
> > for instance), but I couldn't manage to make the kick to happen any
> > faster. Presumably this isn't a problem for things like Bluetooth
> > since flow control saves them. ...and I guess this isn't a problem in
> > practice because we usually _send_ a lot of data to the host for
> > console/kgdb and it's only the host => DUT path that has problems.
> >
> >
> >> I am not sure about what all scenario can leads to this behavior from
> >> hardware, I will try to get an answer from hardware team.
> >>
> >> Any error bit was set for SE_GENI_S_IRQ_STATUS & SE_GENI_M_IRQ_STATUS
> >> registers?
> > As per above I can see overflows in my test case and geni seems to be
> > behaving pretty badly. If you have ideas on how to fix this I'd love
> > it. However, it still seems like my patch is right because (at least
> > in the cases I tested) it avoids dropping bytes in some cases. It
> > also matches how qcom_geni_serial_handle_rx() works and if that was
> > broken we'd have noticed by now.
>
> Reviewed-by: Akash Asthana <akashast@xxxxxxxxxxxxxx>
Thanks! After my extra digging I now think that the weird case is
triggered by the overflows and the FIFO certainly does get garbage in
it when there are overflows, but I think my patch is still correct and
gets correct bytes. The garbage that is queued up is queued up later
and looks like normal transfers. ...so I think we're good to go with
it.
So summary:
1. We should land my patch.
2. I filed <https://crbug.com/1115125> to track trying to make kdb's
polling nicer.
3. I also filed an internal bug to track seeing if we could make geni
not queue up garbage in this case.
-Doug
