From: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx>
commit 1866541492641c02874bf51f9d8712b5510f2c64 upstream
When using RS485 half duplex the Transmitter Complete irq is needed to
determine the moment when the transmitter can be disabled. When using
DMA this irq must only be enabled when DMA has completed to transfer all
data. Otherwise the CPU might busily trigger this irq which is not
properly handled and so the also pending irq for the DMA transfer cannot
trigger.
Cc: <stable@xxxxxxxxxxxxxxx> # v4.14.x
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
[Backport to v4.14]
Signed-off-by: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx>
---
When using RS485 with DMA enabled simply transmitting some data on our
i.MX6ULL based boards often freezes the system completely. The higher
the baudrate, the easier it is to reproduce the issue. To test this I
simply used:
stty -F /dev/ttymxc1 speed 115200
while true; do echo TEST > /dev/ttymxc1; done
Without the patch this leads to an almost immediate system freeze,
with the patch applied, everything keeps working as expected.
---
drivers/tty/serial/imx.c | 23 +++++++++++++++++++----
1 file changed, 19 insertions(+), 4 deletions(-)
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 3f2605edd855..993ab57e7448 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -538,6 +538,11 @@ static void dma_tx_callback(void *data)
if (!uart_circ_empty(xmit) && !uart_tx_stopped(&sport->port))
imx_dma_tx(sport);
+ else if (sport->port.rs485.flags & SER_RS485_ENABLED) {
+ temp = readl(sport->port.membase + UCR4);
+ temp |= UCR4_TCEN;
+ writel(temp, sport->port.membase + UCR4);
+ }
spin_unlock_irqrestore(&sport->port.lock, flags);
}
@@ -555,6 +560,10 @@ static void imx_dma_tx(struct imx_port *sport)
if (sport->dma_is_txing)
return;
+ temp = readl(sport->port.membase + UCR4);
+ temp &= ~UCR4_TCEN;
+ writel(temp, sport->port.membase + UCR4);
+
sport->tx_bytes = uart_circ_chars_pending(xmit);
if (xmit->tail < xmit->head || xmit->head == 0) {
@@ -608,6 +617,7 @@ static void imx_start_tx(struct uart_port *port)
if (port->rs485.flags & SER_RS485_ENABLED) {
temp = readl(port->membase + UCR2);
+
if (port->rs485.flags & SER_RS485_RTS_ON_SEND)
imx_port_rts_active(sport, &temp);
else
@@ -617,10 +627,15 @@ static void imx_start_tx(struct uart_port *port)
if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
imx_stop_rx(port);
- /* enable transmitter and shifter empty irq */
- temp = readl(port->membase + UCR4);
- temp |= UCR4_TCEN;
- writel(temp, port->membase + UCR4);
+ /*
+ * Enable transmitter and shifter empty irq only if DMA is off.
+ * In the DMA case this is done in the tx-callback.
+ */
+ if (!sport->dma_is_enabled) {
+ temp = readl(port->membase + UCR4);
+ temp |= UCR4_TCEN;
+ writel(temp, port->membase + UCR4);
+ }
}
if (!sport->dma_is_enabled) {
--
2.17.1
