Re: [PATCH V4 7/9] tty: serial: qcom_geni_serial: Add interconnect support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Apr 15, 2020 at 03:53:16PM +0530, Akash Asthana wrote:
> Get the interconnect paths for Uart based Serial Engine device
> and vote according to the baud rate requirement of the driver.
> 
> Signed-off-by: Akash Asthana <akashast@xxxxxxxxxxxxxx>
> ---
> Changes in V2:
>  - As per Bjorn's comment, removed se == NULL check from geni_serial_icc_get
>  - As per Bjorn's comment, removed code to set se->icc_path* to NULL in failure
>  - As per Bjorn's comment, introduced and using devm_of_icc_get API for getting
>    path handle
>  - As per Matthias comment, added error handling for icc_set_bw call
> 
> Changes in V3:
>  - As per Matthias comment, use common library APIs defined in geni-se
>    driver for ICC functionality.
> 
> Changes in V4:
>  - As per Mark's comment move peak_bw guess as twice of avg_bw if
>    nothing mentioned explicitly to ICC core.
>  - As per Matthias's comment select core clock BW based on baud rate.
>    If it's less than 115200 go for GENI_DEFAULT_BW else CORE_2X_50_MHZ
> 
>  drivers/tty/serial/qcom_geni_serial.c | 25 ++++++++++++++++++++++---
>  1 file changed, 22 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
> index 8c5d97c..a5b2f1c 100644
> --- a/drivers/tty/serial/qcom_geni_serial.c
> +++ b/drivers/tty/serial/qcom_geni_serial.c
> @@ -965,6 +965,15 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport,
>  	ser_clk_cfg = SER_CLK_EN;
>  	ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
>  
> +	/*
> +	 * Bump up BW vote on CPU and CORE path as driver supports FIFO mode
> +	 * only.
> +	 */
> +	port->se.icc_paths[0].avg_bw = (baud > 115200) ?
> +				Bps_to_icc(CORE_2X_50_MHZ) : GENI_DEFAULT_BW;
> +	port->se.icc_paths[1].avg_bw = Bps_to_icc(baud);

use enums to index the paths

> +	geni_icc_vote_on(&port->se);
> +
>  	/* parity */
>  	tx_trans_cfg = readl(uport->membase + SE_UART_TX_TRANS_CFG);
>  	tx_parity_cfg = readl(uport->membase + SE_UART_TX_PARITY_CFG);
> @@ -1202,11 +1211,14 @@ static void qcom_geni_serial_pm(struct uart_port *uport,
>  	if (old_state == UART_PM_STATE_UNDEFINED)
>  		old_state = UART_PM_STATE_OFF;
>  
> -	if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF)
> +	if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF) {
> +		geni_icc_vote_on(&port->se);
>  		geni_se_resources_on(&port->se);
> -	else if (new_state == UART_PM_STATE_OFF &&
> -			old_state == UART_PM_STATE_ON)
> +	} else if (new_state == UART_PM_STATE_OFF &&
> +			old_state == UART_PM_STATE_ON) {
>  		geni_se_resources_off(&port->se);
> +		geni_icc_vote_off(&port->se);
> +	}
>  }
>  
>  static const struct uart_ops qcom_geni_console_pops = {
> @@ -1304,6 +1316,13 @@ static int qcom_geni_serial_probe(struct platform_device *pdev)
>  			return -ENOMEM;
>  	}
>  
> +	ret = geni_icc_get(&port->se, NULL);
> +	if (ret)
> +		return ret;
> +	/* Set the bus quota to a reasonable value for register access */
> +	port->se.icc_paths[0].avg_bw = GENI_DEFAULT_BW;
> +	port->se.icc_paths[1].avg_bw = GENI_DEFAULT_BW;

The comment isn't very useful, the use of GENI_DEFAULT_BW essentially
implies "a reasonable value". I suggest to drop it.



[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux