On Sun, Dec 01, 2019 at 04:59:14PM +0900, Hyunki Koo wrote:
> From: Shinbeom Choi <sbeom.choi@xxxxxxxxxxx>
>
> This commit enables modulization of samsung uart driver.
>
> There was no way to make use of this driver in other module,
> because uart functions were static.
>
> By exporting required functions, user can use this driver
> in other module.
>
> Signed-off-by: Shinbeom Choi <sbeom.choi@xxxxxxxxxxx>
> Signed-off-by: Hyunki Koo <hyunki00.koo@xxxxxxxxxxx>
> ---
> drivers/tty/serial/samsung.h | 32 ++++++++++++
> drivers/tty/serial/samsung_tty.c | 85 +++++++++++++++-----------------
> 2 files changed, 73 insertions(+), 44 deletions(-)
>
> diff --git a/drivers/tty/serial/samsung.h b/drivers/tty/serial/samsung.h
> index f93022113f59..25be0962284d 100644
> --- a/drivers/tty/serial/samsung.h
> +++ b/drivers/tty/serial/samsung.h
> @@ -144,4 +144,36 @@ static inline void s3c24xx_clear_bit(struct uart_port *port, int idx,
> local_irq_restore(flags);
> }
>
> +#if defined(CONFIG_ARCH_EXYNOS)
> +#define EXYNOS_COMMON_SERIAL_DRV_DATA \
> + .info = &(struct s3c24xx_uart_info) { \
> + .name = "Samsung Exynos UART", \
> + .type = PORT_S3C6400, \
> + .has_divslot = 1, \
> + .rx_fifomask = S5PV210_UFSTAT_RXMASK, \
> + .rx_fifoshift = S5PV210_UFSTAT_RXSHIFT, \
> + .rx_fifofull = S5PV210_UFSTAT_RXFULL, \
> + .tx_fifofull = S5PV210_UFSTAT_TXFULL, \
> + .tx_fifomask = S5PV210_UFSTAT_TXMASK, \
> + .tx_fifoshift = S5PV210_UFSTAT_TXSHIFT, \
> + .def_clk_sel = S3C2410_UCON_CLKSEL0, \
> + .num_clks = 1, \
> + .clksel_mask = 0, \
> + .clksel_shift = 0, \
> + }, \
> + .def_cfg = &(struct s3c2410_uartcfg) { \
> + .ucon = S5PV210_UCON_DEFAULT, \
> + .ufcon = S5PV210_UFCON_DEFAULT, \
> + .has_fracval = 1, \
> + } \
> +
> +#endif
> +
> +int s3c24xx_serial_get_ports(struct s3c24xx_uart_port **ourport, int index);
> +int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
> + struct platform_device *platdev);
> +int s3c24xx_serial_unregister_port(struct platform_device *dev);
> +int s3c24xx_serial_suspend(struct device *dev);
> +int s3c24xx_serial_resume(struct device *dev);
> +int s3c24xx_serial_resume_noirq(struct device *dev);
> #endif
> diff --git a/drivers/tty/serial/samsung_tty.c b/drivers/tty/serial/samsung_tty.c
> index 83fd51607741..15414ecd9008 100644
> --- a/drivers/tty/serial/samsung_tty.c
> +++ b/drivers/tty/serial/samsung_tty.c
> @@ -1735,7 +1735,7 @@ static int s3c24xx_serial_enable_baudclk(struct s3c24xx_uart_port *ourport)
> * initialise a single serial port from the platform device given
> */
>
> -static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
> +int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
> struct platform_device *platdev)
> {
> struct uart_port *port = &ourport->port;
> @@ -1842,12 +1842,24 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
> /* reset the fifos (and setup the uart) */
> s3c24xx_serial_resetport(port, cfg);
>
> + if (!s3c24xx_uart_drv.state) {
> + ret = uart_register_driver(&s3c24xx_uart_drv);
> + if (ret < 0) {
> + dev_err(port->dev, "Failed to register Samsung UART driver\n");
> + return ret;
> + }
> + }
> +
> + dbg("%s: adding port\n", __func__);
> + uart_add_one_port(&s3c24xx_uart_drv, &ourport->port);
> +
> return 0;
>
> err:
> port->mapbase = 0;
> return ret;
> }
> +EXPORT_SYMBOL_GPL(s3c24xx_serial_init_port);
Why are you exporting all of these functions? What other code uses
them? Why are you converting them all to global functions I don't see
any other in-kernel callers, so why are those changes needed here?
totally confused,
greg k-h
