On Tue, Jul 23, 2019 at 04:27:47PM +0300, Mike Bogdanov wrote: > Hi, > I have a problem with 6 serial port card st-lab i-472 > (http://www.stlab.ru/catalog/kontrolleri/controller-st-lab-pci-e-x1-i-472-i- > 470-6-ext-6xcom9m-ret.html). > > i have instaled debian 8. > >root@c000050:~# uname -a > >Linux c000050 4.9.0-0.bpo.9-686-pae #1 SMP Debian 4.9.168-1+deb9u3~deb8u1 > (2019-06-17) i686 GNU/Linux > > > In dmesg i found the follow message with yuor email: > [ 2.180347] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled > [ 2.207661] 00:01: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a > 16550A > [ 2.237213] 0000:01:00.0: ttyS4 at I/O 0xe050 (irq = 16, base_baud = 115200) > is a ST16650V2 > [ 2.266932] 0000:01:00.0: ttyS5 at I/O 0xe040 (irq = 16, base_baud = 115200) > is a ST16650V2 > [ 2.296576] 0000:01:00.1: ttyS6 at I/O 0xe030 (irq = 17, base_baud = 115200) > is a ST16650V2 > [ 2.326296] 0000:01:00.1: ttyS7 at I/O 0xe020 (irq = 17, base_baud = 115200) > is a ST16650V2 > [ 2.334970] serial 0000:01:00.2: NetMos/Mostech serial driver ignoring port > on ambiguous config. > [ 2.343895] serial 0000:01:00.2: 0000:01:00.2: unknown NetMos/Mostech device > Please send the output of lspci -vv, this > message (0x9710,0x9900,0xa000,0x1000), the > manufacturer and name of serial board or > modem board to <linux-serial@xxxxxxxxxxxxxxx>. > [ 2.371816] serial 0000:01:00.3: NetMos/Mostech serial driver ignoring port > on ambiguous config. > [ 2.380734] serial 0000:01:00.3: 0000:01:00.3: unknown NetMos/Mostech device > Please send the output of lspci -vv, this > message (0x9710,0x9900,0xa000,0x1000), the > manufacturer and name of serial board or > modem board to <linux-serial@xxxxxxxxxxxxxxx>. > > Odd, this "should" work. Nicos added support for this back in the 3.1 kernel, but odds are something has changed in the hardware since then. Does the device work properly even with these messages? Nicos, any idea? lspci-v output below for reference. thanks, greg k-h ---------------------------------------------------------- > > Can you give advice how can i start this board? > > My lspci is below > ----------------------------------------------- > 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen > Core Processor Host Bridge/DRAM Registers (rev 07) > Subsystem: Gigabyte Technology Co., Ltd Device 5000 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ >SERR- <PERR- INTx- > Latency: 0 > Capabilities: [e0] Vendor Specific Information: Len=10 <?> > Kernel driver in use: skl_uncore > > 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen > Core Processor PCIe Controller (x16) (rev 07) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 0000e000-0000efff > Memory behind bridge: ef100000-ef1fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [88] Subsystem: Gigabyte Technology Co., Ltd Device > 5000 > Capabilities: [80] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- > Address: fee0300c Data: 4161 > Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 256 bytes, PhantFunc 0 > ExtTag- RBE+ > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 256 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- > TransPend- > LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, Exit > Latency L0s <1us, L1 <8us > ClockPM- Surprise- LLActRep- BwNot+ > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive- BWMgmt+ ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- > Surprise- > Slot #1, PowerLimit 75.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- > HPIrq- LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ > Interlock- > Changed: MRL- PresDet+ LinkState- > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, > LTR+, OBFF Via WAKE# ARIFwd- > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, > LTR+, OBFF Via WAKE# ARIFwd- > LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- > SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -6dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [100 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- > WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > Status: NegoPending- InProgress- > Capabilities: [140 v1] Root Complex Link > Desc: PortNumber=02 ComponentID=01 EltType=Config > Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- > LinkType=MemMapped LinkValid+ > Addr: 00000000fed19000 > Capabilities: [d94 v1] #19 > Kernel driver in use: pcieport > > 00:02.0 VGA compatible controller: Intel Corporation HD Graphics 510 (rev > 06) (prog-if 00 [VGA controller]) > Subsystem: Gigabyte Technology Co., Ltd Device d000 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 125 > Region 0: Memory at ee000000 (64-bit, non-prefetchable) [size=16M] > Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] > Region 4: I/O ports at f000 [size=64] > [virtual] Expansion ROM at 000c0000 [disabled] [size=128K] > Capabilities: [40] Vendor Specific Information: Len=0c <?> > Capabilities: [70] Express (v2) Root Complex Integrated Endpoint, > MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0 > ExtTag- RBE+ > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- > TransPend- > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, > LTR-, OBFF Not Supported > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, > LTR-, OBFF Disabled > Capabilities: [ac] MSI: Enable+ Count=1/1 Maskable- 64bit- > Address: fee0300c Data: 41e1 > Capabilities: [d0] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [100 v1] #1b > Capabilities: [200 v1] Address Translation Service (ATS) > ATSCap: Invalidate Queue Depth: 00 > ATSCtl: Enable-, Smallest Translation Unit: 00 > Capabilities: [300 v1] #13 > Kernel driver in use: i915 > > 00:14.0 USB controller: Intel Corporation 100 Series/C230 Series Chipset > Family USB 3.0 xHCI Controller (rev 31) (prog-if 30 [XHCI]) > Subsystem: Gigabyte Technology Co., Ltd Device 5007 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 122 > Region 0: Memory at ef210000 (64-bit, non-prefetchable) [size=64K] > Capabilities: [70] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0-,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+ > Address: 00000000fee0300c Data: 41b1 > Kernel driver in use: xhci_hcd > > 00:16.0 Communication controller: Intel Corporation 100 Series/C230 Series > Chipset Family MEI Controller #1 (rev 31) > Subsystem: Gigabyte Technology Co., Ltd Device 1c3a > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 124 > Region 0: Memory at ef22d000 (64-bit, non-prefetchable) [size=4K] > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot+,D3cold-) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee0300c Data: 41d1 > Kernel driver in use: mei_me > > 00:17.0 SATA controller: Intel Corporation > Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode] (rev > 31) (prog-if 01 [AHCI 1.0]) > Subsystem: Gigabyte Technology Co., Ltd Device b005 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 123 > Region 0: Memory at ef228000 (32-bit, non-prefetchable) [size=8K] > Region 1: Memory at ef22c000 (32-bit, non-prefetchable) [size=256] > Region 2: I/O ports at f090 [size=8] > Region 3: I/O ports at f080 [size=4] > Region 4: I/O ports at f060 [size=32] > Region 5: Memory at ef22b000 (32-bit, non-prefetchable) [size=2K] > Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- > Address: fee0100c Data: 41c1 > Capabilities: [70] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot+,D3cold-) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004 > Kernel driver in use: ahci > > 00:1c.0 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family > PCI Express Root Port #5 (rev f1) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 256 bytes, PhantFunc 0 > ExtTag- RBE+ > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #5, Speed 5GT/s, Width x4, ASPM not supported, > Exit Latency L0s unlimited, L1 <16us > ClockPM- Surprise- LLActRep+ BwNot+ > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- > Surprise- > Slot #8, PowerLimit 25.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- > HPIrq- LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- > Interlock- > Changed: MRL- PresDet- LinkState- > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+, > OBFF Not Supported ARIFwd+ > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, > LTR+, OBFF Disabled ARIFwd- > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- > SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -3.5dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- > Address: 00000000 Data: 0000 > Capabilities: [90] Subsystem: Gigabyte Technology Co., Ltd Device > 5001 > Capabilities: [a0] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr- > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- > ChkEn- > Capabilities: [140 v1] Access Control Services > ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ > UpstreamFwd- EgressCtrl- DirectTrans- > ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- > UpstreamFwd- EgressCtrl- DirectTrans- > Kernel driver in use: pcieport > > 00:1d.0 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family > PCI Express Root Port #9 (rev f1) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > I/O behind bridge: 0000d000-0000dfff > Memory behind bridge: ef000000-ef0fffff > Prefetchable memory behind bridge: 00000000e0000000-00000000e00fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0 > ExtTag- RBE+ > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #9, Speed 5GT/s, Width x1, ASPM not supported, > Exit Latency L0s <1us, L1 <16us > ClockPM- Surprise- LLActRep+ BwNot+ > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive+ BWMgmt+ ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- > Surprise- > Slot #12, PowerLimit 10.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- > HPIrq- LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ > Interlock- > Changed: MRL- PresDet- LinkState+ > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+, > OBFF Not Supported ARIFwd+ > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, > LTR+, OBFF Disabled ARIFwd- > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- > SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -3.5dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- > Address: 00000000 Data: 0000 > Capabilities: [90] Subsystem: Gigabyte Technology Co., Ltd Device > 5001 > Capabilities: [a0] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr- > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- > ChkEn- > Capabilities: [140 v1] Access Control Services > ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ > UpstreamFwd- EgressCtrl- DirectTrans- > ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- > UpstreamFwd- EgressCtrl- DirectTrans- > Kernel driver in use: pcieport > > 00:1d.1 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family > PCI Express Root Port #10 (rev f1) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 256 bytes, PhantFunc 0 > ExtTag- RBE+ > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #10, Speed 5GT/s, Width x1, ASPM not supported, > Exit Latency L0s unlimited, L1 <16us > ClockPM- Surprise- LLActRep+ BwNot+ > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- > Surprise- > Slot #13, PowerLimit 10.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- > HPIrq- LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- > Interlock- > Changed: MRL- PresDet- LinkState- > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+, > OBFF Not Supported ARIFwd+ > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, > LTR+, OBFF Disabled ARIFwd- > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- > SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -3.5dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- > Address: 00000000 Data: 0000 > Capabilities: [90] Subsystem: Gigabyte Technology Co., Ltd Device > 5001 > Capabilities: [a0] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr- > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- > ChkEn- > Capabilities: [140 v1] Access Control Services > ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ > UpstreamFwd- EgressCtrl- DirectTrans- > ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- > UpstreamFwd- EgressCtrl- DirectTrans- > Kernel driver in use: pcieport > > 00:1f.0 ISA bridge: Intel Corporation H110 Chipset LPC/eSPI Controller (rev > 31) > Subsystem: Gigabyte Technology Co., Ltd Device 5001 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > > 00:1f.2 Memory controller: Intel Corporation 100 Series/C230 Series Chipset > Family Power Management Controller (rev 31) > Subsystem: Gigabyte Technology Co., Ltd Device 5001 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Region 0: Memory at ef224000 (32-bit, non-prefetchable) [size=16K] > > 00:1f.3 Audio device: Intel Corporation 100 Series/C230 Series Chipset > Family HD Audio Controller (rev 31) > Subsystem: Gigabyte Technology Co., Ltd Device a182 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 126 > Region 0: Memory at ef220000 (64-bit, non-prefetchable) [size=16K] > Region 4: Memory at ef200000 (64-bit, non-prefetchable) [size=64K] > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA > PME(D0-,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee0300c Data: 4122 > Kernel driver in use: snd_hda_intel > > 00:1f.4 SMBus: Intel Corporation 100 Series/C230 Series Chipset Family SMBus > (rev 31) > Subsystem: Gigabyte Technology Co., Ltd Device 5001 > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at ef22a000 (64-bit, non-prefetchable) [size=256] > Region 4: I/O ports at f040 [size=32] > Kernel driver in use: i801_smbus > > 01:00.0 Communication controller: MosChip Semiconductor Technology Ltd. > MCS9900 Multi-I/O Controller > Subsystem: Device a000:3002 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Region 0: I/O ports at e050 [size=8] > Region 1: Memory at ef109000 (32-bit, non-prefetchable) [size=4K] > Region 3: I/O ports at e040 [size=8] > Region 4: Memory at ef108000 (32-bit, non-prefetchable) [size=4K] > Region 5: Memory at ef107000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+ > Address: 0000000000000000 Data: 0000 > Capabilities: [78] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0-,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [80] Express (v1) Legacy Endpoint, MSI 00 > DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, > L1 <2us > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 256 bytes, MaxReadReq 512 bytes > DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- > TransPend- > LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit > Latency L0s <64ns, L1 <1us > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- > DLActive- BWMgmt- ABWMgmt- > Capabilities: [100 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- > WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > Status: NegoPending- InProgress- > VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- > WRR256- > Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00 > Status: NegoPending- InProgress- > Capabilities: [800 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- > ChkEn- > Kernel driver in use: serial > > 01:00.1 Communication controller: MosChip Semiconductor Technology Ltd. > MCS9900 Multi-I/O Controller > Subsystem: Device a000:3002 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 17 > Region 0: I/O ports at e030 [size=8] > Region 1: Memory at ef106000 (32-bit, non-prefetchable) [size=4K] > Region 3: I/O ports at e020 [size=8] > Region 4: Memory at ef105000 (32-bit, non-prefetchable) [size=4K] > Region 5: Memory at ef104000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+ > Address: 0000000000000000 Data: 0000 > Capabilities: [78] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0-,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [80] Express (v1) Legacy Endpoint, MSI 00 > DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, > L1 <2us > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 256 bytes, MaxReadReq 512 bytes > DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- > TransPend- > LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit > Latency L0s <64ns, L1 <1us > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- > DLActive- BWMgmt- ABWMgmt- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- > ChkEn- > Kernel driver in use: serial > > 01:00.2 Communication controller: MosChip Semiconductor Technology Ltd. > MCS9900 Multi-I/O Controller > Subsystem: Device a000:1000 > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin C routed to IRQ 18 > Region 0: I/O ports at e010 [size=8] > Region 1: Memory at ef103000 (32-bit, non-prefetchable) [size=4K] > Region 5: Memory at ef102000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+ > Address: 0000000000000000 Data: 0000 > Capabilities: [78] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0-,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [80] Express (v1) Legacy Endpoint, MSI 00 > DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, > L1 <2us > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 256 bytes, MaxReadReq 512 bytes > DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- > TransPend- > LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit > Latency L0s <64ns, L1 <1us > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- > DLActive- BWMgmt- ABWMgmt- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- > ChkEn- > > 01:00.3 Communication controller: MosChip Semiconductor Technology Ltd. > MCS9900 Multi-I/O Controller > Subsystem: Device a000:1000 > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin D routed to IRQ 19 > Region 0: I/O ports at e000 [size=8] > Region 1: Memory at ef101000 (32-bit, non-prefetchable) [size=4K] > Region 5: Memory at ef100000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+ > Address: 0000000000000000 Data: 0000 > Capabilities: [78] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0-,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [80] Express (v1) Legacy Endpoint, MSI 00 > DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, > L1 <2us > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 256 bytes, MaxReadReq 512 bytes > DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- > TransPend- > LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit > Latency L0s <64ns, L1 <1us > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- > DLActive- BWMgmt- ABWMgmt- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- > ChkEn- > > 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. > RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c) > Subsystem: Gigabyte Technology Co., Ltd Onboard Ethernet > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 121 > Region 0: I/O ports at d000 [size=256] > Region 2: Memory at ef000000 (64-bit, non-prefetchable) [size=4K] > Region 4: Memory at e0000000 (64-bit, prefetchable) [size=16K] > Capabilities: [40] Power Management version 3 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA > PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee0200c Data: 41a1 > Capabilities: [70] Express (v2) Endpoint, MSI 01 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s > <512ns, L1 <64us > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 4096 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit > Latency L0s unlimited, L1 <64us > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ > ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, > OBFF Via message/WAKE# > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, > LTR+, OBFF Disabled > LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- > SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -6dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [b0] MSI-X: Enable- Count=4 Masked- > Vector table: BAR=4 offset=00000000 > PBA: BAR=4 offset=00000800 > Capabilities: [d0] Vital Product Data > Not readable > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr- > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ > ChkEn- > Capabilities: [140 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- > WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > Status: NegoPending- InProgress- > Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00 > Capabilities: [170 v1] Latency Tolerance Reporting > Max snoop latency: 3145728ns > Max no snoop latency: 3145728ns > Kernel driver in use: r8169 > ----------------------------------------------- > > > Best Regards, > Bogdanov Mike > > >
