Fix checkpatch warnings:
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
#38: FILE: drivers/tty/serial/sunzilog.c:38:
+#include <asm/io.h>
WARNING: line over 80 characters
#109: FILE: drivers/tty/serial/sunzilog.c:109:
+#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel __iomem *)((PORT)->membase))
WARNING: line over 80 characters
#116: FILE: drivers/tty/serial/sunzilog.c:116:
+#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS)
WARNING: line over 80 characters
#179: FILE: drivers/tty/serial/sunzilog.c:179:
+static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs)
WARNING: Missing a blank line after declarations
#188: FILE: drivers/tty/serial/sunzilog.c:188:
+ unsigned char stat = read_zsreg(channel, R1);
+ if (stat & ALL_SNT)
ERROR: trailing whitespace
#231: FILE: drivers/tty/serial/sunzilog.c:231:
+^I$
WARNING: braces {} are not necessary for any arm of this statement
#276: FILE: drivers/tty/serial/sunzilog.c:276:
+ if (ZS_TX_ACTIVE(up)) {
[...]
+ } else {
[...]
ERROR: else should follow close brace '}'
#378: FILE: drivers/tty/serial/sunzilog.c:378:
+ }
+ else if (r1 & PAR_ERR)
ERROR: code indent should use tabs where possible
#397: FILE: drivers/tty/serial/sunzilog.c:397:
+^I^I ^Itty_insert_flip_char(port, ch, flag);$
WARNING: please, no space before tabs
#397: FILE: drivers/tty/serial/sunzilog.c:397:
+^I^I ^Itty_insert_flip_char(port, ch, flag);$
WARNING: line over 80 characters
#440: FILE: drivers/tty/serial/sunzilog.c:440:
+ /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
WARNING: line over 80 characters
#441: FILE: drivers/tty/serial/sunzilog.c:441:
+ * But it does not tell us which bit has changed, we have to keep
WARNING: Missing a blank line after declarations
#464: FILE: drivers/tty/serial/sunzilog.c:464:
+ unsigned char status = readb(&channel->control);
+ ZSDELAY();
WARNING: line over 80 characters
#468: FILE: drivers/tty/serial/sunzilog.c:468:
+ * It can occur because of how we do serial console writes. It would
WARNING: line over 80 characters
#469: FILE: drivers/tty/serial/sunzilog.c:469:
+ * be nice to transmit console writes just like we normally would for
WARNING: line over 80 characters
#470: FILE: drivers/tty/serial/sunzilog.c:470:
+ * a TTY line. (ie. buffered and TX interrupt driven). That is not
WARNING: line over 80 characters
#471: FILE: drivers/tty/serial/sunzilog.c:471:
+ * easy because console writes cannot sleep. One solution might be
WARNING: line over 80 characters
#593: FILE: drivers/tty/serial/sunzilog.c:593:
+static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port)
WARNING: plain inline is preferred over __inline__
#593: FILE: drivers/tty/serial/sunzilog.c:593:
+static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port)
ERROR: trailing whitespace
#664: FILE: drivers/tty/serial/sunzilog.c:664:
+^I/* NOTE: Not subject to 'transmitter active' rule. */ $
ERROR: trailing whitespace
#752: FILE: drivers/tty/serial/sunzilog.c:752:
+^I^I/* NOTE: Not subject to 'transmitter active' rule. */ $
ERROR: trailing whitespace
#779: FILE: drivers/tty/serial/sunzilog.c:779:
+^I^I/* NOTE: Not subject to 'transmitter active' rule. */ $
WARNING: line over 80 characters
#999: FILE: drivers/tty/serial/sunzilog.c:999:
+static int sunzilog_verify_port(struct uart_port *port, struct serial_struct *ser)
WARNING: Missing a blank line after declarations
#1142: FILE: drivers/tty/serial/sunzilog.c:1142:
+ unsigned char val = readb(&channel->control);
+ if (val & Tx_BUF_EMP) {
WARNING: Prefer [subsystem eg: netdev]_info([subsystem]dev, ... then dev_info(dev, ... then pr_info(... to printk(KERN_INFO ...
#1230: FILE: drivers/tty/serial/sunzilog.c:1230:
+ printk(KERN_INFO "Console: ttyS%d (SunZilog zs%d)\n",
WARNING: braces {} are not necessary for single statement blocks
#1383: FILE: drivers/tty/serial/sunzilog.c:1383:
+ if (__load_zsregs(channel, up->curregs)) {
+ up->flags |= SUNZILOG_FLAG_ESCC;
+ }
WARNING: quoted string split across lines
#1493: FILE: drivers/tty/serial/sunzilog.c:1493:
+ dev_info(&op->dev, "Keyboard at MMIO 0x%llx (irq = %d) "
+ "is a %s\n",
WARNING: quoted string split across lines
#1497: FILE: drivers/tty/serial/sunzilog.c:1497:
+ dev_info(&op->dev, "Mouse at MMIO 0x%llx (irq = %d) "
+ "is a %s\n",
WARNING: Missing a blank line after declarations
#1581: FILE: drivers/tty/serial/sunzilog.c:1581:
+ struct uart_sunzilog_port *up = sunzilog_irq_chain;
+ err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED,
WARNING: line over 80 characters
#1590: FILE: drivers/tty/serial/sunzilog.c:1590:
+ /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */
WARNING: line over 80 characters
#1627: FILE: drivers/tty/serial/sunzilog.c:1627:
+ /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */
ERROR: trailing statements should be on next line
#1248: FILE: drivers/tty/serial/sunzilog.c:1248:
+ case B150: baud = 150; break;
ERROR: trailing statements should be on next line
#1249: FILE: drivers/tty/serial/sunzilog.c:1249:
+ case B300: baud = 300; break;
ERROR: trailing statements should be on next line
#1250: FILE: drivers/tty/serial/sunzilog.c:1250:
+ case B600: baud = 600; break;
ERROR: trailing statements should be on next line
#1251: FILE: drivers/tty/serial/sunzilog.c:1251:
+ case B1200: baud = 1200; break;
ERROR: trailing statements should be on next line
#1252: FILE: drivers/tty/serial/sunzilog.c:1252:
+ case B2400: baud = 2400; break;
ERROR: trailing statements should be on next line
#1253: FILE: drivers/tty/serial/sunzilog.c:1253:
+ case B4800: baud = 4800; break;
ERROR: trailing statements should be on next line
#1254: FILE: drivers/tty/serial/sunzilog.c:1254:
+ default: case B9600: baud = 9600; break;
ERROR: trailing statements should be on next line
#1255: FILE: drivers/tty/serial/sunzilog.c:1255:
+ case B19200: baud = 19200; break;
ERROR: trailing statements should be on next line
#1256: FILE: drivers/tty/serial/sunzilog.c:1256:
+ case B38400: baud = 38400; break;
Signed-off-by: Enrico Weigelt <info@xxxxxxxxx>
---
drivers/tty/serial/sunzilog.c | 118 +++++++++++++++++++++++++++---------------
1 file changed, 76 insertions(+), 42 deletions(-)
diff --git a/drivers/tty/serial/sunzilog.c b/drivers/tty/serial/sunzilog.c
index 6285bba..17b0520 100644
--- a/drivers/tty/serial/sunzilog.c
+++ b/drivers/tty/serial/sunzilog.c
@@ -106,14 +106,17 @@ struct uart_sunzilog_port {
static void sunzilog_putchar(struct uart_port *port, int ch);
-#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel __iomem *)((PORT)->membase))
-#define UART_ZILOG(PORT) ((struct uart_sunzilog_port *)(PORT))
+#define ZILOG_CHANNEL_FROM_PORT(PORT) \
+ ((struct zilog_channel __iomem *)((PORT)->membase))
+#define UART_ZILOG(PORT) \
+ ((struct uart_sunzilog_port *)(PORT))
#define ZS_IS_KEYB(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_KEYB)
#define ZS_IS_MOUSE(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_MOUSE)
#define ZS_IS_CONS(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CONS)
#define ZS_IS_KGDB(UP) ((UP)->flags & SUNZILOG_FLAG_IS_KGDB)
-#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS)
+#define ZS_WANTS_MODEM_STATUS(UP) \
+ ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS)
#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CHANNEL_A)
#define ZS_REGS_HELD(UP) ((UP)->flags & SUNZILOG_FLAG_REGS_HELD)
#define ZS_TX_STOPPED(UP) ((UP)->flags & SUNZILOG_FLAG_TX_STOPPED)
@@ -176,7 +179,8 @@ static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel)
/* This function must only be called when the TX is not busy. The UART
* port lock must be held and local interrupts disabled.
*/
-static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs)
+static int __load_zsregs(struct zilog_channel __iomem *channel,
+ unsigned char *regs)
{
int i;
int escc;
@@ -185,6 +189,7 @@ static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *r
/* Let pending transmits finish. */
for (i = 0; i < 1000; i++) {
unsigned char stat = read_zsreg(channel, R1);
+
if (stat & ALL_SNT)
break;
udelay(100);
@@ -228,7 +233,7 @@ static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *r
/* Lower and upper byte of baud rate generator divisor. */
write_zsreg(channel, R12, regs[R12]);
write_zsreg(channel, R13, regs[R13]);
-
+
/* Now rewrite R14, with BRENAB (if set). */
write_zsreg(channel, R14, regs[R14]);
@@ -273,11 +278,10 @@ static void sunzilog_maybe_update_regs(struct uart_sunzilog_port *up,
struct zilog_channel __iomem *channel)
{
if (!ZS_REGS_HELD(up)) {
- if (ZS_TX_ACTIVE(up)) {
+ if (ZS_TX_ACTIVE(up))
up->flags |= SUNZILOG_FLAG_REGS_HELD;
- } else {
+ else
__load_zsregs(channel, up->curregs);
- }
}
}
@@ -374,8 +378,7 @@ static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up,
up->port.icount.brk++;
if (uart_handle_break(&up->port))
continue;
- }
- else if (r1 & PAR_ERR)
+ } else if (r1 & PAR_ERR)
up->port.icount.parity++;
else if (r1 & CRC_ERR)
up->port.icount.frame++;
@@ -394,7 +397,7 @@ static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up,
if (up->port.ignore_status_mask == 0xff ||
(r1 & up->port.ignore_status_mask) == 0) {
- tty_insert_flip_char(port, ch, flag);
+ tty_insert_flip_char(port, ch, flag);
}
if (r1 & Rx_OVR)
tty_insert_flip_char(port, 0, TTY_OVERRUN);
@@ -437,9 +440,9 @@ static void sunzilog_status_handle(struct uart_sunzilog_port *up,
if (status & SYNC)
up->port.icount.dsr++;
- /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
- * But it does not tell us which bit has changed, we have to keep
- * track of this ourselves.
+ /* The Zilog just gives us an interrupt when DCD/CTS/etc.
+ * change.But it does not tell us which bit has changed,
+ * we have to keep track of this ourselves.
*/
if ((status ^ up->prev_status) ^ DCD)
uart_handle_dcd_change(&up->port,
@@ -461,15 +464,17 @@ static void sunzilog_transmit_chars(struct uart_sunzilog_port *up,
if (ZS_IS_CONS(up)) {
unsigned char status = readb(&channel->control);
+
ZSDELAY();
/* TX still busy? Just wait for the next TX done interrupt.
*
- * It can occur because of how we do serial console writes. It would
- * be nice to transmit console writes just like we normally would for
- * a TTY line. (ie. buffered and TX interrupt driven). That is not
- * easy because console writes cannot sleep. One solution might be
- * to poll on enough port->xmit space becoming free. -DaveM
+ * It can occur because of how we do serial console writes.
+ * It would be nice to transmit console writes just like we
+ * normally would for a TTY line. (ie. buffered and TX
+ * interrupt driven). That is not easy because console
+ * writes cannot sleep. One solution might be to poll on
+ * enough port->xmit space becoming free. -DaveM
*/
if (!(status & Tx_BUF_EMP))
return;
@@ -590,7 +595,8 @@ static irqreturn_t sunzilog_interrupt(int irq, void *dev_id)
/* A convenient way to quickly get R0 status. The caller must _not_ hold the
* port lock, it is acquired here.
*/
-static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port)
+static inline unsigned char
+sunzilog_read_channel_status(struct uart_port *port)
{
struct zilog_channel __iomem *channel;
unsigned char status;
@@ -661,13 +667,13 @@ static void sunzilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
else
clear_bits |= DTR;
- /* NOTE: Not subject to 'transmitter active' rule. */
+ /* NOTE: Not subject to 'transmitter active' rule. */
up->curregs[R5] |= set_bits;
up->curregs[R5] &= ~clear_bits;
write_zsreg(channel, R5, up->curregs[R5]);
}
-/* The port lock is held and interrupts are disabled. */
+/* The port lock is held and interrupts are disabled. */
static void sunzilog_stop_tx(struct uart_port *port)
{
struct uart_sunzilog_port *up =
@@ -749,7 +755,7 @@ static void sunzilog_enable_ms(struct uart_port *port)
if (new_reg != up->curregs[R15]) {
up->curregs[R15] = new_reg;
- /* NOTE: Not subject to 'transmitter active' rule. */
+ /* NOTE: Not subject to 'transmitter active' rule. */
write_zsreg(channel, R15, up->curregs[R15] & ~WR7pEN);
}
}
@@ -776,7 +782,7 @@ static void sunzilog_break_ctl(struct uart_port *port, int break_state)
if (new_reg != up->curregs[R5]) {
up->curregs[R5] = new_reg;
- /* NOTE: Not subject to 'transmitter active' rule. */
+ /* NOTE: Not subject to 'transmitter active' rule. */
write_zsreg(channel, R5, up->curregs[R5]);
}
@@ -996,7 +1002,8 @@ static void sunzilog_config_port(struct uart_port *port, int flags)
}
/* We do not support letting the user mess with the divisor, IRQ, etc. */
-static int sunzilog_verify_port(struct uart_port *port, struct serial_struct *ser)
+static int sunzilog_verify_port(struct uart_port *port,
+ struct serial_struct *ser)
{
return -EINVAL;
}
@@ -1139,6 +1146,7 @@ static void sunzilog_putchar(struct uart_port *port, int ch)
*/
do {
unsigned char val = readb(&channel->control);
+
if (val & Tx_BUF_EMP) {
ZSDELAY();
break;
@@ -1237,15 +1245,34 @@ static int __init sunzilog_console_setup(struct console *con, char *options)
* this hackish cflag thing is OK.
*/
switch (con->cflag & CBAUD) {
- case B150: baud = 150; break;
- case B300: baud = 300; break;
- case B600: baud = 600; break;
- case B1200: baud = 1200; break;
- case B2400: baud = 2400; break;
- case B4800: baud = 4800; break;
- default: case B9600: baud = 9600; break;
- case B19200: baud = 19200; break;
- case B38400: baud = 38400; break;
+ case B150:
+ baud = 150;
+ break;
+ case B300:
+ baud = 300;
+ break;
+ case B600:
+ baud = 600;
+ break;
+ case B1200:
+ baud = 1200;
+ break;
+ case B2400:
+ baud = 2400;
+ break;
+ case B4800:
+ baud = 4800;
+ break;
+ default:
+ case B9600:
+ baud = 9600;
+ break;
+ case B19200:
+ baud = 19200;
+ break;
+ case B38400:
+ baud = 38400;
+ break;
}
brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
@@ -1380,9 +1407,9 @@ static void sunzilog_init_hw(struct uart_sunzilog_port *up)
up->curregs[R14] = BRSRC | BRENAB;
up->curregs[R15] = FIFOEN; /* Use FIFO if on ESCC */
up->curregs[R7p] = TxFIFO_LVL | RxFIFO_LVL;
- if (__load_zsregs(channel, up->curregs)) {
+ if (__load_zsregs(channel, up->curregs))
up->flags |= SUNZILOG_FLAG_ESCC;
- }
+
/* Only enable interrupts if an ISR handler available */
if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
up->curregs[R9] |= MIE;
@@ -1489,12 +1516,12 @@ static int zs_probe(struct platform_device *op)
}
uart_inst++;
} else {
- dev_info(&op->dev, "Keyboard at MMIO 0x%llx (irq = %d) "
- "is a %s\n",
+ dev_info(&op->dev,
+ "Keyboard at MMIO 0x%llx (irq = %d) is a %s\n",
(unsigned long long) up[0].port.mapbase,
op->archdata.irqs[0], sunzilog_type(&up[0].port));
- dev_info(&op->dev, "Mouse at MMIO 0x%llx (irq = %d) "
- "is a %s\n",
+ dev_info(&op->dev,
+ "Mouse at MMIO 0x%llx (irq = %d) is a %s\n",
(unsigned long long) up[1].port.mapbase,
op->archdata.irqs[0], sunzilog_type(&up[1].port));
kbm_inst++;
@@ -1578,6 +1605,7 @@ static int __init sunzilog_init(void)
if (zilog_irq) {
struct uart_sunzilog_port *up = sunzilog_irq_chain;
+
err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED,
"zs", sunzilog_irq_chain);
if (err)
@@ -1587,7 +1615,10 @@ static int __init sunzilog_init(void)
while (up) {
struct zilog_channel __iomem *channel;
- /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */
+ /* printk(KERN_INFO
+ * "Enable IRQ for ZILOG Hardware %p\n",
+ * up);
+ */
channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
up->flags |= SUNZILOG_FLAG_ISR_HANDLER;
up->curregs[R9] |= MIE;
@@ -1624,7 +1655,10 @@ static void __exit sunzilog_exit(void)
while (up) {
struct zilog_channel __iomem *channel;
- /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */
+ /* printk(KERN_INFO
+ * "Disable IRQ for ZILOG Hardware %p\n",
+ * up);
+ */
channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
up->flags &= ~SUNZILOG_FLAG_ISR_HANDLER;
up->curregs[R9] &= ~MIE;
--
1.9.1
