Add DMA support for 32-bit variant of the LPUART, such as LS1021A.
Signed-off-by: Tomonori Sakita <tomonori.sakita@xxxxxxxxxx>
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@xxxxxxxxxx>
---
drivers/tty/serial/fsl_lpuart.c | 191 ++++++++++++++++++++++++++++++++++------
1 file changed, 162 insertions(+), 29 deletions(-)
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index d0a98ec..f651a0d 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -426,6 +426,17 @@ static void lpuart_dma_tx_complete(void *arg)
spin_unlock_irqrestore(&sport->port.lock, flags);
}
+static dma_addr_t lpuart_dma_datareg_addr(struct lpuart_port *sport)
+{
+ switch (sport->port.iotype) {
+ case UPIO_MEM32:
+ return sport->port.mapbase + UARTDATA;
+ case UPIO_MEM32BE:
+ return sport->port.mapbase + UARTDATA + sizeof(u32) - 1;
+ }
+ return sport->port.mapbase + UARTDR;
+}
+
static int lpuart_dma_tx_request(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port,
@@ -433,7 +444,7 @@ static int lpuart_dma_tx_request(struct uart_port *port)
struct dma_slave_config dma_tx_sconfig = {};
int ret;
- dma_tx_sconfig.dst_addr = sport->port.mapbase + UARTDR;
+ dma_tx_sconfig.dst_addr = lpuart_dma_datareg_addr(sport);
dma_tx_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
dma_tx_sconfig.dst_maxburst = 1;
dma_tx_sconfig.direction = DMA_MEM_TO_DEV;
@@ -636,13 +647,19 @@ static void lpuart_start_tx(struct uart_port *port)
static void lpuart32_start_tx(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
+ struct circ_buf *xmit = &sport->port.state->xmit;
unsigned long temp;
- temp = lpuart32_read(port, UARTCTRL);
- lpuart32_write(port, temp | UARTCTRL_TIE, UARTCTRL);
+ if (sport->lpuart_dma_tx_use) {
+ if (!uart_circ_empty(xmit) && !uart_tx_stopped(port))
+ lpuart_dma_tx(sport);
+ } else {
+ temp = lpuart32_read(port, UARTCTRL);
+ lpuart32_write(port, temp | UARTCTRL_TIE, UARTCTRL);
- if (lpuart32_read(port, UARTSTAT) & UARTSTAT_TDRE)
- lpuart32_transmit_buffer(sport);
+ if (lpuart32_read(port, UARTSTAT) & UARTSTAT_TDRE)
+ lpuart32_transmit_buffer(sport);
+ }
}
/* return TIOCSER_TEMT when transmitter is not busy */
@@ -872,11 +889,10 @@ static irqreturn_t lpuart32_int(int irq, void *dev_id)
rxcount = lpuart32_read(&sport->port, UARTWATER);
rxcount = rxcount >> UARTWATER_RXCNT_OFF;
- if (sts & UARTSTAT_RDRF || rxcount > 0)
+ if ((sts & UARTSTAT_RDRF || rxcount > 0) && !sport->lpuart_dma_rx_use)
lpuart32_rxint(irq, dev_id);
- if ((sts & UARTSTAT_TDRE) &&
- !(lpuart32_read(&sport->port, UARTBAUD) & UARTBAUD_TDMAE))
+ if ((sts & UARTSTAT_TDRE) && !sport->lpuart_dma_tx_use)
lpuart_txint(irq, dev_id);
lpuart32_write(&sport->port, sts, UARTSTAT);
@@ -891,18 +907,31 @@ static void lpuart_copy_rx_to_tty(struct lpuart_port *sport)
struct circ_buf *ring = &sport->rx_ring;
unsigned long flags;
int count = 0;
- unsigned char sr;
- sr = readb(sport->port.membase + UARTSR1);
+ if (lpuart_is_32(sport)) {
+ unsigned long sr = lpuart32_read(&sport->port, UARTSTAT);
- if (sr & (UARTSR1_PE | UARTSR1_FE)) {
- /* Read DR to clear the error flags */
- readb(sport->port.membase + UARTDR);
+ if (sr & (UARTSTAT_PE | UARTSTAT_FE)) {
+ /* Read DR to clear the error flags */
+ lpuart32_read(&sport->port, UARTDATA);
+
+ if (sr & UARTSTAT_PE)
+ sport->port.icount.parity++;
+ else if (sr & UARTSTAT_FE)
+ sport->port.icount.frame++;
+ }
+ } else {
+ unsigned char sr = readb(sport->port.membase + UARTSR1);
+
+ if (sr & (UARTSR1_PE | UARTSR1_FE)) {
+ /* Read DR to clear the error flags */
+ readb(sport->port.membase + UARTDR);
- if (sr & UARTSR1_PE)
- sport->port.icount.parity++;
- else if (sr & UARTSR1_FE)
- sport->port.icount.frame++;
+ if (sr & UARTSR1_PE)
+ sport->port.icount.parity++;
+ else if (sr & UARTSR1_FE)
+ sport->port.icount.frame++;
+ }
}
async_tx_ack(sport->dma_rx_desc);
@@ -1025,7 +1054,7 @@ static inline int lpuart_start_rx_dma(struct lpuart_port *sport)
return -EINVAL;
}
- dma_rx_sconfig.src_addr = sport->port.mapbase + UARTDR;
+ dma_rx_sconfig.src_addr = lpuart_dma_datareg_addr(sport);
dma_rx_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
dma_rx_sconfig.src_maxburst = 1;
dma_rx_sconfig.direction = DMA_DEV_TO_MEM;
@@ -1053,8 +1082,14 @@ static inline int lpuart_start_rx_dma(struct lpuart_port *sport)
sport->dma_rx_cookie = dmaengine_submit(sport->dma_rx_desc);
dma_async_issue_pending(sport->dma_rx_chan);
- writeb(readb(sport->port.membase + UARTCR5) | UARTCR5_RDMAS,
- sport->port.membase + UARTCR5);
+ if (lpuart_is_32(sport)) {
+ unsigned long temp = lpuart32_read(&sport->port, UARTBAUD);
+
+ lpuart32_write(&sport->port, temp | UARTBAUD_RDMAE, UARTBAUD);
+ } else {
+ writeb(readb(sport->port.membase + UARTCR5) | UARTCR5_RDMAS,
+ sport->port.membase + UARTCR5);
+ }
return 0;
}
@@ -1354,8 +1389,41 @@ static int lpuart32_startup(struct uart_port *port)
lpuart32_setup_watermark(sport);
temp = lpuart32_read(&sport->port, UARTCTRL);
- temp |= (UARTCTRL_RIE | UARTCTRL_TIE | UARTCTRL_RE | UARTCTRL_TE);
- temp |= UARTCTRL_ILIE;
+ temp |= UARTCTRL_RE | UARTCTRL_TE | UARTCTRL_ILIE;
+ lpuart32_write(&sport->port, temp, UARTCTRL);
+
+ if (sport->dma_rx_chan && !lpuart_start_rx_dma(sport)) {
+ /* set Rx DMA timeout */
+ sport->dma_rx_timeout = msecs_to_jiffies(DMA_RX_TIMEOUT);
+ if (!sport->dma_rx_timeout)
+ sport->dma_rx_timeout = 1;
+
+ sport->lpuart_dma_rx_use = true;
+ rx_dma_timer_init(sport);
+ } else {
+ sport->lpuart_dma_rx_use = false;
+ }
+
+ if (sport->dma_tx_chan && !lpuart_dma_tx_request(port)) {
+ init_waitqueue_head(&sport->dma_wait);
+ sport->lpuart_dma_tx_use = true;
+ temp = lpuart32_read(&sport->port, UARTBAUD);
+ lpuart32_write(&sport->port, temp | UARTBAUD_TDMAE, UARTBAUD);
+ } else {
+ sport->lpuart_dma_tx_use = false;
+ }
+
+ if (sport->lpuart_dma_rx_use) {
+ /* RXWATER must be 0 */
+ temp = lpuart32_read(&sport->port, UARTWATER);
+ temp &= ~(UARTWATER_WATER_MASK << UARTWATER_RXWATER_OFF);
+ lpuart32_write(&sport->port, temp, UARTWATER);
+ }
+ temp = lpuart32_read(&sport->port, UARTCTRL);
+ if (!sport->lpuart_dma_rx_use)
+ temp |= UARTCTRL_RIE;
+ if (!sport->lpuart_dma_tx_use)
+ temp |= UARTCTRL_TIE;
lpuart32_write(&sport->port, temp, UARTCTRL);
spin_unlock_irqrestore(&sport->port.lock, flags);
@@ -1396,6 +1464,8 @@ static void lpuart_shutdown(struct uart_port *port)
static void lpuart32_shutdown(struct uart_port *port)
{
+ struct lpuart_port *sport =
+ container_of(port, struct lpuart_port, port);
unsigned long temp;
unsigned long flags;
@@ -1408,6 +1478,21 @@ static void lpuart32_shutdown(struct uart_port *port)
lpuart32_write(port, temp, UARTCTRL);
spin_unlock_irqrestore(&port->lock, flags);
+
+ if (sport->lpuart_dma_rx_use) {
+ del_timer_sync(&sport->lpuart_timer);
+ lpuart_dma_rx_free(&sport->port);
+ }
+
+ if (sport->lpuart_dma_tx_use) {
+ if (wait_event_interruptible(sport->dma_wait,
+ !sport->dma_tx_in_progress)) {
+ sport->dma_tx_in_progress = false;
+ dmaengine_terminate_all(sport->dma_tx_chan);
+ }
+
+ lpuart32_stop_tx(port);
+ }
}
static void
@@ -1633,7 +1718,10 @@ lpuart32_serial_setbrg(struct lpuart_port *sport, unsigned int baudrate)
tmp &= ~UARTBAUD_SBR_MASK;
tmp |= sbr & UARTBAUD_SBR_MASK;
- tmp &= ~(UARTBAUD_TDMAE | UARTBAUD_RDMAE);
+ if (!sport->lpuart_dma_rx_use)
+ tmp &= ~UARTBAUD_RDMAE;
+ if (!sport->lpuart_dma_tx_use)
+ tmp &= ~UARTBAUD_TDMAE;
lpuart32_write(&sport->port, tmp, UARTBAUD);
}
@@ -1711,6 +1799,18 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
/* ask the core to calculate the divisor */
baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 4);
+ /*
+ * Need to update the Ring buffer length according to the selected
+ * baud rate and restart Rx DMA path.
+ *
+ * Since timer function acqures sport->port.lock, need to stop before
+ * acquring same lock because otherwise del_timer_sync() can deadlock.
+ */
+ if (old && sport->lpuart_dma_rx_use) {
+ del_timer_sync(&sport->lpuart_timer);
+ lpuart_dma_rx_free(&sport->port);
+ }
+
spin_lock_irqsave(&sport->port.lock, flags);
sport->port.read_status_mask = 0;
@@ -1749,6 +1849,13 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
lpuart32_write(&sport->port, ctrl, UARTCTRL);
/* restore control register */
+ if (old && sport->lpuart_dma_rx_use) {
+ if (!lpuart_start_rx_dma(sport))
+ rx_dma_timer_init(sport);
+ else
+ sport->lpuart_dma_rx_use = false;
+ }
+
spin_unlock_irqrestore(&sport->port.lock, flags);
}
@@ -2318,8 +2425,13 @@ static int lpuart_suspend(struct device *dev)
}
/* Disable Rx DMA to use UART port as wakeup source */
- writeb(readb(sport->port.membase + UARTCR5) & ~UARTCR5_RDMAS,
- sport->port.membase + UARTCR5);
+ if (lpuart_is_32(sport)) {
+ temp = lpuart32_read(&sport->port, UARTBAUD);
+ lpuart32_write(port, temp & ~UARTBAUD_RDMAE, UARTBAUD);
+ } else {
+ writeb(readb(sport->port.membase + UARTCR5) &
+ ~UARTCR5_RDMAS, sport->port.membase + UARTCR5);
+ }
}
if (sport->lpuart_dma_tx_use) {
@@ -2345,8 +2457,7 @@ static int lpuart_resume(struct device *dev)
if (lpuart_is_32(sport)) {
lpuart32_setup_watermark(sport);
temp = lpuart32_read(&sport->port, UARTCTRL);
- temp |= (UARTCTRL_RIE | UARTCTRL_TIE | UARTCTRL_RE |
- UARTCTRL_TE | UARTCTRL_ILIE);
+ temp |= UARTCTRL_RE | UARTCTRL_TE | UARTCTRL_ILIE;
lpuart32_write(&sport->port, temp, UARTCTRL);
} else {
lpuart_setup_watermark(sport);
@@ -2365,14 +2476,36 @@ static int lpuart_resume(struct device *dev)
}
if (sport->dma_tx_chan && !lpuart_dma_tx_request(&sport->port)) {
- init_waitqueue_head(&sport->dma_wait);
- sport->lpuart_dma_tx_use = true;
+ init_waitqueue_head(&sport->dma_wait);
+ sport->lpuart_dma_tx_use = true;
+ if (lpuart_is_32(sport)) {
+ temp = lpuart32_read(&sport->port, UARTBAUD);
+ lpuart32_write(&sport->port,
+ temp | UARTBAUD_TDMAE, UARTBAUD);
+ } else {
writeb(readb(sport->port.membase + UARTCR5) |
UARTCR5_TDMAS, sport->port.membase + UARTCR5);
+ }
} else {
sport->lpuart_dma_tx_use = false;
}
+ if (lpuart_is_32(sport)) {
+ if (sport->lpuart_dma_rx_use) {
+ /* RXWATER must be 0 */
+ temp = lpuart32_read(&sport->port, UARTWATER);
+ temp &= ~(UARTWATER_WATER_MASK <<
+ UARTWATER_RXWATER_OFF);
+ lpuart32_write(&sport->port, temp, UARTWATER);
+ }
+ temp = lpuart32_read(&sport->port, UARTCTRL);
+ if (!sport->lpuart_dma_rx_use)
+ temp |= UARTCTRL_RIE;
+ if (!sport->lpuart_dma_tx_use)
+ temp |= UARTCTRL_TIE;
+ lpuart32_write(&sport->port, temp, UARTCTRL);
+ }
+
uart_resume_port(&lpuart_reg, &sport->port);
return 0;
--
2.1.4
