From: Jeremy Cline <jeremy@xxxxxxxxxx> Implement support for the RTL8723BS chip. Signed-off-by: Jeremy Cline <jeremy@xxxxxxxxxx> [hdegoede@xxxxxxxxxx: Port from bt3wire.c to hci_h5.c, drop broken GPIO code] Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx> --- drivers/bluetooth/hci_h5.c | 69 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 69 insertions(+) diff --git a/drivers/bluetooth/hci_h5.c b/drivers/bluetooth/hci_h5.c index b3f762291e7f..3513dad43f3c 100644 --- a/drivers/bluetooth/hci_h5.c +++ b/drivers/bluetooth/hci_h5.c @@ -31,6 +31,7 @@ #include <net/bluetooth/bluetooth.h> #include <net/bluetooth/hci_core.h> +#include "btrtl.h" #include "hci_uart.h" #define HCI_3WIRE_ACK_PKT 0 @@ -822,11 +823,79 @@ static void h5_serdev_remove(struct serdev_device *serdev) hci_uart_unregister_device(&h5->serdev_hu); } +static int h5_btrtl_setup(struct h5 *h5) +{ + struct btrtl_device_info *btrtl_dev; + struct sk_buff *skb; + __le32 baudrate_data; + u32 device_baudrate; + unsigned int controller_baudrate; + bool flow_control; + int err; + + btrtl_dev = btrtl_initialize(h5->hu->hdev, h5->id); + if (IS_ERR(btrtl_dev)) + return PTR_ERR(btrtl_dev); + + err = btrtl_get_uart_settings(h5->hu->hdev, btrtl_dev, + &controller_baudrate, &device_baudrate, + &flow_control); + if (err) + goto out_free; + + baudrate_data = cpu_to_le32(device_baudrate); + skb = __hci_cmd_sync(h5->hu->hdev, 0xfc17, sizeof(baudrate_data), + &baudrate_data, HCI_INIT_TIMEOUT); + if (IS_ERR(skb)) { + rtl_dev_err(h5->hu->hdev, "set baud rate command failed\n"); + err = PTR_ERR(skb); + goto out_free; + } else { + kfree_skb(skb); + } + /* Give the device some time to set up the new baudrate. */ + usleep_range(10000, 20000); + + serdev_device_set_baudrate(h5->hu->serdev, controller_baudrate); + serdev_device_set_flow_control(h5->hu->serdev, flow_control); + + err = btrtl_download_firmware(h5->hu->hdev, btrtl_dev); + /* Give the device some time before the hci-core sends it a reset */ + usleep_range(10000, 20000); + +out_free: + btrtl_free(btrtl_dev); + + return err; +} + +static void h5_btrtl_open(struct h5 *h5) +{ + /* Devices always start with these fixed parameters */ + serdev_device_set_flow_control(h5->hu->serdev, false); + serdev_device_set_parity(h5->hu->serdev, SERDEV_PARITY_EVEN); + serdev_device_set_baudrate(h5->hu->serdev, 115200); +} + +static struct h5_vnd rtl_vnd = { + .setup = h5_btrtl_setup, + .open = h5_btrtl_open, +}; + +#ifdef CONFIG_ACPI +static const struct acpi_device_id h5_acpi_match[] = { + { "OBDA8723", (kernel_ulong_t)&rtl_vnd }, + { }, +}; +MODULE_DEVICE_TABLE(acpi, h5_acpi_match); +#endif + static struct serdev_device_driver h5_serdev_driver = { .probe = h5_serdev_probe, .remove = h5_serdev_remove, .driver = { .name = "hci_uart_h5", + .acpi_match_table = ACPI_PTR(h5_acpi_match), }, }; -- 2.18.0 -- To unsubscribe from this list: send the line "unsubscribe linux-serial" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html