Re: [RFC 3/7] dt: bindings: Add nokia-bluetooth

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sat, Aug 13, 2016 at 05:14:34AM +0200, Sebastian Reichel wrote:
> ---
>  .../devicetree/bindings/net/nokia-bluetooth.txt    | 43 ++++++++++++++++++++++
>  1 file changed, 43 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/nokia-bluetooth.txt
> 
> diff --git a/Documentation/devicetree/bindings/net/nokia-bluetooth.txt b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt
> new file mode 100644
> index 000000000000..a0fceabb4cce
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt
> @@ -0,0 +1,43 @@
> +Nokia bluetooth UART devices
> +------
> +
> +Some vendors have custom versions of their chips, that can be found in Nokia
> +devices. These chips are controlled differently, than the non-Nokia version,
> +so a different binding is required. All chips listed here implement the Nokia
> +H4+ protocol.
> +
> +Required properties:
> +
> +  - compatible: should be one of the following:
> +	* "nokia,brcm,bcm2048"
> +	* "nokia,ti,wl1271-bluetooth"

Perhaps these should be 2 separate strings. Something like 
'"nokia,n900-bt", "brcm,bcm2048"'. However, if they are in no way 
compatible with the default version from the vendors, then just a single 
string is fine, but it doesn't need to be aligned to the vendor 
compatible string. So just "nokia,n900-bcm2048" or similar is fine.

> +  - reset-gpios:		Should specify the gpio for bluetooth reset
> +  - host-wakeup-gpios:		Should specify the gpio for host wakeup

Should be interrupt instead?

> +  - bluetooth-wakeup-gpios:	Should specify the gpio for bluetooth wakeup

State direction and active state for gpios.

> +  - clock-names:		Should be "sysclk"
> +  - clocks:			Should contain a clock phandle for system clock
> +
> +Example:
> +
> +/ {
> +	/* controlled (enabled/disabled) directly by wl1271 */
> +	vctcxo: vctcxo {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <38400000>;
> +	};
> +};
> +
> +&uart2 {

I want to see a common serial device binding doc before accepting any 
device bindings. It's not going to say much initially other than devices 
are child nodes of uarts. Perhaps something on baudrate settings.

> +	bluetooth {
> +		compatible = "nokia,ti,wl1271-bluetooth";
> +
> +		reset-gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>; /* 26 */
> +		host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* 101 */
> +		bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* 37 */
> +
> +		clocks = <&vctcxo>;
> +		clock-names = "sysclk";
> +	};
> +
> +};
> -- 
> 2.8.1
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux