When the clk_get() of "uart" clock returns EPROBE_DEFER, the next re-probe
finishes with success but uses invalid (ERR_PTR) values. This leads to
dereferencing of ERR_PTR stored under ourport->clk:
12c30000.serial: Controller clock not found
(...)
12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
Unable to handle kernel paging request at virtual address fffffdfb
(clk_prepare) from [<c039f7d0>] (s3c24xx_serial_pm+0x20/0x128)
(s3c24xx_serial_pm) from [<c0395414>] (uart_change_pm+0x38/0x40)
(uart_change_pm) from [<c039689c>] (uart_add_one_port+0x31c/0x44c)
(uart_add_one_port) from [<c03a035c>] (s3c24xx_serial_probe+0x2a8/0x418)
(s3c24xx_serial_probe) from [<c03ee110>] (platform_drv_probe+0x50/0xb0)
(platform_drv_probe) from [<c03ecb44>] (driver_probe_device+0x1f4/0x2b0)
(driver_probe_device) from [<c03eb0c0>] (bus_for_each_drv+0x44/0x8c)
(bus_for_each_drv) from [<c03ec8c8>] (__device_attach+0x9c/0x100)
(__device_attach) from [<c03ebf54>] (bus_probe_device+0x84/0x8c)
(bus_probe_device) from [<c03ec388>] (deferred_probe_work_func+0x60/0x8c)
(deferred_probe_work_func) from [<c012fee4>] (process_one_work+0x120/0x328)
(process_one_work) from [<c0130150>] (worker_thread+0x2c/0x4ac)
(worker_thread) from [<c0135320>] (kthread+0xd8/0xf4)
(kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
The first unsuccessful clk_get() causes s3c24xx_serial_init_port() to
exit with failure but the s3c24xx_uart_port is left half-configured
(e.g. port->mapbase is set, clk contains ERR_PTR). On next re-probe,
the function s3c24xx_serial_init_port() will exit early with success
because of configured port->mapbase and driver will use old values,
including the ERR_PTR as clock.
Fix this by cleaning the port->mapbase on error path so each re-probe
will initialize all of the port settings.
Fixes: 60e93575476f ("serial: samsung: enable clock before clearing pending interrupts during init")
Cc: <stable@xxxxxxxxxxxxxxx>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
---
Changes since v1:
1. Apply suggestion from Bartlomiej (offline) that early check for
port->mapbase in s3c24xx_serial_init_port() should fail if it is
already set. The port->mapbase is now always cleared when probe
fails, so re-probing with 'port->mapbase != 0' is unexpected.
---
drivers/tty/serial/samsung.c | 18 +++++++++++++-----
1 file changed, 13 insertions(+), 5 deletions(-)
diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c
index 99bb23161dd6..f0bd2ec0db59 100644
--- a/drivers/tty/serial/samsung.c
+++ b/drivers/tty/serial/samsung.c
@@ -1684,7 +1684,7 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
return -ENODEV;
if (port->mapbase != 0)
- return 0;
+ return -EINVAL;
/* setup info for port */
port->dev = &platdev->dev;
@@ -1738,22 +1738,25 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
ourport->dma = devm_kzalloc(port->dev,
sizeof(*ourport->dma),
GFP_KERNEL);
- if (!ourport->dma)
- return -ENOMEM;
+ if (!ourport->dma) {
+ ret = -ENOMEM;
+ goto err;
+ }
}
ourport->clk = clk_get(&platdev->dev, "uart");
if (IS_ERR(ourport->clk)) {
pr_err("%s: Controller clock not found\n",
dev_name(&platdev->dev));
- return PTR_ERR(ourport->clk);
+ ret = PTR_ERR(ourport->clk);
+ goto err;
}
ret = clk_prepare_enable(ourport->clk);
if (ret) {
pr_err("uart: clock failed to prepare+enable: %d\n", ret);
clk_put(ourport->clk);
- return ret;
+ goto err;
}
/* Keep all interrupts masked and cleared */
@@ -1769,7 +1772,12 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
/* reset the fifos (and setup the uart) */
s3c24xx_serial_resetport(port, cfg);
+
return 0;
+
+err:
+ port->mapbase = 0;
+ return ret;
}
/* Device driver serial port probe */
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
