Re: [RFC PATCH] always probe UART HW when options are not specified

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 12/17/2015 10:21 AM, Sebastian Frias wrote:
> On 12/17/2015 06:48 PM, Peter Hurley wrote:
>> On 12/17/2015 08:48 AM, Sebastian Frias wrote:
>>> On 12/17/2015 05:29 PM, Peter Hurley wrote:
>>>> On 12/17/2015 07:15 AM, Sebastian Frias wrote:
>>>>> ---
>>>>>
>>>>> I think there are a few minor bugs on the 8250 UART code.
>>>>>
>>>>> Below you can find a patch with a proposed solution.
>>>>>
>>>>> In a nutshell:
>>>>> - probe_baud from 87515772c33ee8a0cc08d984a7d2401eeff074cd was
>>>>> converted into probe_port so that it reads all the parameters that
>>>>> uart_set_options require (namely baud, parity, bits, flow).
>>>>> - reading/writing to UART_DLL/UART_DLM directly are converted to
>>>>> using the read_dl/write_dl callbacks.
>>>>> - the port is always probed if there are no options (*).
>>>>
>>>> Because I don't want to probe the port at all.
>>>>
>>>> But must when using the
>>>>      earlycon=ttyS0,....
>>
>> Sorry, ignore this. I meant "console=uart"
>>
>>>> command-line (because the original hack expects that behavior).
>>>
>>> Ok, we are using:
>>>
>>> "console=ttyS0 earlyprintk"
>>>
>>> and the 8250 (with CONFIG_SERIAL_8250_RT288X=y) driver.
>>>
>>> The hardware is setup prior to Linux boot.
>>> We don't want Linux to change the UART settings, just to pick up whatever settings the UART has and take over UART.
>>>
>>> How do you suggest we do that? Right now, since it does not probe, it just messes up the UART config setup before booting Linux.
>>>
>>> While on the subject, do you think you could explain the difference (or similarity) between:
>>> - "console=ttyS0"
>>> - "console=uart"
>>> - "earlycon=uart"
>>> and how they relate to "earlyprintk" (if at all)?
>>>
>>> Maybe some of those options are soon to be deprecated and we'd like to stick with the standard and future-proof way.
>>
>> All of the above choices are future-proof because kernel command
>> line options are considered userspace.
>>
> 
> It's confusing though, given there are multiple ways to express the same thing.
> I also found parts of the doc confusing in that regard as well.
> ie: there's also a "stdout-path" DT key.

Yep. Thing is, once it goes into the command line and someone uses it,
it's permanent.

That's why it's important to get the semantics right the first time
(which only looks easy from hindsight).


>> So
>>
>>    "console=ttyS0" w/o options    always initializes the h/w to 9600n81
> 
> Ok, I see. So that's not the option we need then.
> 
>>    "earlycon=uart" w/o options    starts a bootconsole w/o initializing the h/w
>>    "console=uart" w/o options     starts a bootconsole w/o initializing the h/w,
>>                                   then replaces that bootconsole with a regular
>>                                   console (whatever ttySn matched that port)
>>                                   In this case, the port is probed to discover
>>                                   the h/w settings. Those also become the initial
>>                                   settings for the /dev/ttySn device.
> 
> Ok, sounds like that last one is the one we need, I will check that, thanks.
> 
>>
>> earlyprintk is implemented by arch-specific code, whereas earlycon is implemented
>> by the serial driver code.
>>
>> Since earlyprintk is implemented in the arch code, it can be tweaked for
>> earlier use than early param parsing. There were some patches earlier this
>> year for x86 to initialize earlyprintk very early; not sure if they were
>> ever upstreamed. On ARM, earlyprintk is debug_ll.
> 
> So there are 3 levels of console?
> earlyprintk: before early param
> earlycon: early param?
> console: after early param?
> 
> What's the use case for earlycon if earlyprink is operational by then?

They serve different masters.

Earlyprintk can be crucial for debugging arch-dependent code. For example,
earlycon expects page tables to be setup, whereas earlyprintk on many
arches does not. Earlyprintk is not tied to the driver source at all.

Earlycon is arch-independent and lives with the serial drivers. This makes
it more suitable to support different flavors of serial h/w. Earlycon is
now the boot console for driver developers and post-early init.

I've noticed an increasing tendency for shipping product to also use
earlyprintk/earlycon; I think this is a terrible idea. Boot consoles should
be for debugging only.



>> Feel free to submit regular patches; reading the divisor via the 8250 port
>> driver is definitely a good idea.
>>
>> Not to sure about probing for other than baud though; do you really want
>> 7 data bits and even parity?  Or are you just trying to get enable h/w
>> flow?
>>
> 
> Actually, I was doing that for completeness, I can remove that part
> of the code if it is wrong or unnecessary, although I'd thought that
> one always wanted correct code.

Well, it's just one more thing to have to maintain, so if you don't actually
need those features, I'd rather not add that.


> In our case, just forcing the probe was enough because only the baud
> rate could change, but if other parameters were to differ,
> set_termios would overwrite them with the "n8r" defaults. 

Ok.

Regards,
Peter Hurley

--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux