Re: [PATCH 03/13] serial: 8250_dma: Support for deferred probing when requesting DMA channels

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



* Peter Ujfalusi <peter.ujfalusi@xxxxxx> [150526 06:28]:
> Switch to use ma_request_slave_channel_compat_reason() to request the DMA
> channels. In case of error, return the error code we received including
> -EPROBE_DEFER
> 
> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@xxxxxx>
> CC: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
> ---
>  drivers/tty/serial/8250/8250_dma.c | 18 ++++++++----------
>  1 file changed, 8 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/tty/serial/8250/8250_dma.c b/drivers/tty/serial/8250/8250_dma.c
> index 21d01a491405..a617eca4e97d 100644
> --- a/drivers/tty/serial/8250/8250_dma.c
> +++ b/drivers/tty/serial/8250/8250_dma.c
> @@ -182,21 +182,19 @@ int serial8250_request_dma(struct uart_8250_port *p)
>  	dma_cap_set(DMA_SLAVE, mask);
>  
>  	/* Get a channel for RX */
> -	dma->rxchan = dma_request_slave_channel_compat(mask,
> -						       dma->fn, dma->rx_param,
> -						       p->port.dev, "rx");
> -	if (!dma->rxchan)
> -		return -ENODEV;
> +	dma->rxchan = dma_request_slave_channel_compat_reason(mask, dma->fn,
> +					dma->rx_param, p->port.dev, "rx");
> +	if (IS_ERR(dma->rxchan))
> +		return PTR_ERR(dma->rxchan);
>  
>  	dmaengine_slave_config(dma->rxchan, &dma->rxconf);
>  
>  	/* Get a channel for TX */
> -	dma->txchan = dma_request_slave_channel_compat(mask,
> -						       dma->fn, dma->tx_param,
> -						       p->port.dev, "tx");
> -	if (!dma->txchan) {
> +	dma->txchan = dma_request_slave_channel_compat_reason(mask, dma->fn,
> +					dma->tx_param, p->port.dev, "tx");
> +	if (IS_ERR(dma->txchan)) {
>  		dma_release_channel(dma->rxchan);
> -		return -ENODEV;
> +		return PTR_ERR(dma->txchan);
>  	}
>  
>  	dmaengine_slave_config(dma->txchan, &dma->txconf);

In general the drivers need to work just fine also without DMA.

Does this handle the case properly where no DMA channel is configured
for the driver in the dts file?

Regards,

Tony
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux