The USART controller on sam9x5 chips (and also all AT91/SAMA5 chips but at91rm9200) are not capable of handling DTR/DSR/DCD/RI signal. Moreover, even if the controller can handle CTS/RTS, the dedicated CTS/RTS pins are already muxed for other peripherals (LCDC/EMAC/MMC). So this patchset adds the possibility to control those lines via GPIO, as it is done for RTS in the patch "switch atmel serial to use gpiolib" As it was suggested by Alexander Shiyan, I made that available for every board. Patch 1 implements the generic helpers to control modem lines via GPIO Patches 2 and 3 are just a little tidy up of atmel_serial.c. Patch 4 implements modem control lines in atmel_serial atmel_serial. Patch 5 implement the interrupts of CTS/DSR/DCD/RI. This is based on next-20140226 + [PATCH v3 5/7] ARM: at91: gpio: implement get_direction That Nicolas (has/will/might) appl(ied/y) on AT91 tree. Tested on at91sam9g35, with a null modem cable between 2 serial ports, one with CTS/RTS controlled by the USART controller, the other via GPIO, full duplex transfers. Did some tests also with null modem cables on a PC, and with real modems. Updates from v3: - add static keyword on struct uart0_gpios_table. - add use an index at the mctrl_gpio_init() function to make it usable by driver that allocates several ports at once. - hide struct gpio_desc from users. - patch "pinctrl: at91: implement get_direction" has been picked by Linus. - patch "ARM: at91: gpio: implement get_direction" has been acked by Linus. Updates from v2: - remove UART_GPIO_MIN/UART_GPIO_MAX_INPUT and use a direction boolean instead. - implement get_direction in at91 pinctrl and mach-at91/gpio.c. - remove the get_mctrl_gpio_name() function that was used for logs only. - split atmel_serial.c patch in 2. - use a gpio lookup table to declare modem gpios in platform devices boards. So there's no more special case for platform data gpios in atmel_serial.c. Updates from v1: - Instead of controlling modem signal only on atmel board, the code is now available for every board. - The active low flag from device tree is now used. Richard Genoud (5): tty/serial: Add GPIOLIB helpers for controlling modem lines tty/serial: at91: use dev_err instead of printk tty/serial: at91: remove unused open/close hooks tty/serial: at91: use mctrl_gpio helpers tty/serial: at91: add interrupts for modem control lines Documentation/serial/driver | 25 +++ arch/arm/mach-at91/at91rm9200_devices.c | 16 +- arch/arm/mach-at91/at91sam9260_devices.c | 7 - arch/arm/mach-at91/at91sam9261_devices.c | 4 - arch/arm/mach-at91/at91sam9263_devices.c | 4 - arch/arm/mach-at91/at91sam9g45_devices.c | 5 - arch/arm/mach-at91/at91sam9rl_devices.c | 5 - drivers/tty/serial/Kconfig | 4 + drivers/tty/serial/Makefile | 3 + drivers/tty/serial/atmel_serial.c | 259 ++++++++++++++++++++++++------- drivers/tty/serial/serial_mctrl_gpio.c | 146 +++++++++++++++++ drivers/tty/serial/serial_mctrl_gpio.h | 109 +++++++++++++ include/linux/platform_data/atmel.h | 1 - 13 files changed, 496 insertions(+), 92 deletions(-) create mode 100644 drivers/tty/serial/serial_mctrl_gpio.c create mode 100644 drivers/tty/serial/serial_mctrl_gpio.h -- 1.8.5 -- To unsubscribe from this list: send the line "unsubscribe linux-serial" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
