[PATCH V2 1/3] serial: rp2: New driver for Comtrol RocketPort 2 cards

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Signed-off-by: Kevin Cernekee <cernekee@xxxxxxxxx>
---
 drivers/tty/serial/Kconfig       |   24 ++
 drivers/tty/serial/Makefile      |    1 +
 drivers/tty/serial/rp2.c         |  882 ++++++++++++++++++++++++++++++++++++++
 include/uapi/linux/serial_core.h |    3 +
 4 files changed, 910 insertions(+)
 create mode 100644 drivers/tty/serial/rp2.c


V1->V2 changes:

 - Fix tty locking in rp2_rx_chars()
 - Add readl() before udelay(), to make sure posted writes have cleared
 - Use udev firmware loading for the microcode blob
 - Remove deprecated __devinit and __devexit macros
 - Change device name to "ttyRP" to avoid conflicts with rocket.c
 - Add MODULE_DEVICE_TABLE

I set up a system with both old (rocket.c) and new (rp2.c) cards, and
verified that the appropriate driver(s) are loaded based on the PCI
device tables.


diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 59c23d0..555f3ca 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1447,4 +1447,28 @@ config SERIAL_ARC_NR_PORTS
 	  Set this to the number of serial ports you want the driver
 	  to support.
 
+config SERIAL_RP2
+	tristate "Comtrol RocketPort EXPRESS/INFINITY support"
+	depends on PCI
+	select SERIAL_CORE
+	help
+	  This driver supports the Comtrol RocketPort EXPRESS and
+	  RocketPort INFINITY families of PCI/PCIe multiport serial adapters.
+	  These adapters use a "RocketPort 2" ASIC that is not compatible
+	  with the original RocketPort driver (CONFIG_ROCKETPORT).
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called rp2.
+
+	  If you want to compile this driver into the kernel, say Y here.  If
+	  you don't have a suitable RocketPort card installed, say N.
+
+config SERIAL_RP2_NR_UARTS
+	int "Maximum number of RocketPort EXPRESS/INFINITY ports"
+	depends on SERIAL_RP2
+	default "32"
+	help
+	  If multiple cards are present, the default limit of 32 ports may
+	  need to be increased.
+
 endmenu
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index df1b998..a582ee9 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -83,3 +83,4 @@ obj-$(CONFIG_SERIAL_SIRFSOC) += sirfsoc_uart.o
 obj-$(CONFIG_SERIAL_AR933X)   += ar933x_uart.o
 obj-$(CONFIG_SERIAL_EFM32_UART) += efm32-uart.o
 obj-$(CONFIG_SERIAL_ARC)	+= arc_uart.o
+obj-$(CONFIG_SERIAL_RP2)	+= rp2.o
diff --git a/drivers/tty/serial/rp2.c b/drivers/tty/serial/rp2.c
new file mode 100644
index 0000000..9e0e4ac
--- /dev/null
+++ b/drivers/tty/serial/rp2.c
@@ -0,0 +1,882 @@
+/*
+ * Driver for Comtrol RocketPort EXPRESS/INFINITY cards
+ *
+ * Copyright (C) 2012 Kevin Cernekee <cernekee@xxxxxxxxx>
+ *
+ * Inspired by, and loosely based on:
+ *
+ *   ar933x_uart.c
+ *     Copyright (C) 2011 Gabor Juhos <juhosg@xxxxxxxxxxx>
+ *
+ *   rocketport_infinity_express-linux-1.20.tar.gz
+ *     Copyright (C) 2004-2011 Comtrol, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/bitops.h>
+#include <linux/compiler.h>
+#include <linux/completion.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/log2.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/slab.h>
+#include <linux/sysrq.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/types.h>
+
+#define DRV_NAME			"rp2"
+
+#define RP2_FW_NAME			"rp2.fw"
+#define RP2_UCODE_BYTES			0x3f
+
+#define PORTS_PER_ASIC			16
+#define ALL_PORTS_MASK			(BIT(PORTS_PER_ASIC) - 1)
+
+#define UART_CLOCK			44236800
+#define DEFAULT_BAUD_DIV		(UART_CLOCK / (9600 * 16))
+#define FIFO_SIZE			512
+
+/* BAR0 registers */
+#define RP2_FPGA_CTL0			0x110
+#define RP2_FPGA_CTL1			0x11c
+#define RP2_IRQ_MASK			0x1ec
+#define RP2_IRQ_MASK_EN_m		BIT(0)
+#define RP2_IRQ_STATUS			0x1f0
+
+/* BAR1 registers */
+#define RP2_ASIC_SPACING		0x1000
+#define RP2_ASIC_OFFSET(i)		((i) << ilog2(RP2_ASIC_SPACING))
+
+#define RP2_PORT_BASE			0x000
+#define RP2_PORT_SPACING		0x040
+
+#define RP2_UCODE_BASE			0x400
+#define RP2_UCODE_SPACING		0x80
+
+#define RP2_CLK_PRESCALER		0xc00
+#define RP2_CH_IRQ_STAT			0xc04
+#define RP2_CH_IRQ_MASK			0xc08
+#define RP2_ASIC_IRQ			0xd00
+#define RP2_ASIC_IRQ_EN_m		BIT(20)
+#define RP2_GLOBAL_CMD			0xd0c
+#define RP2_ASIC_CFG			0xd04
+
+/* port registers */
+#define RP2_DATA_DWORD			0x000
+
+#define RP2_DATA_BYTE			0x008
+#define RP2_DATA_BYTE_ERR_PARITY_m	BIT(8)
+#define RP2_DATA_BYTE_ERR_OVERRUN_m	BIT(9)
+#define RP2_DATA_BYTE_ERR_FRAMING_m	BIT(10)
+#define RP2_DATA_BYTE_BREAK_m		BIT(11)
+
+/* This lets uart_insert_char() drop bytes received on a !CREAD port */
+#define RP2_DUMMY_READ			BIT(16)
+
+#define RP2_DATA_BYTE_EXCEPTION_MASK	(RP2_DATA_BYTE_ERR_PARITY_m | \
+					 RP2_DATA_BYTE_ERR_OVERRUN_m | \
+					 RP2_DATA_BYTE_ERR_FRAMING_m | \
+					 RP2_DATA_BYTE_BREAK_m)
+
+#define RP2_RX_FIFO_COUNT		0x00c
+#define RP2_TX_FIFO_COUNT		0x00e
+
+#define RP2_CHAN_STAT			0x010
+#define RP2_CHAN_STAT_RXDATA_m		BIT(0)
+#define RP2_CHAN_STAT_DCD_m		BIT(3)
+#define RP2_CHAN_STAT_DSR_m		BIT(4)
+#define RP2_CHAN_STAT_CTS_m		BIT(5)
+#define RP2_CHAN_STAT_RI_m		BIT(6)
+#define RP2_CHAN_STAT_OVERRUN_m		BIT(13)
+#define RP2_CHAN_STAT_DSR_CHANGED_m	BIT(16)
+#define RP2_CHAN_STAT_CTS_CHANGED_m	BIT(17)
+#define RP2_CHAN_STAT_CD_CHANGED_m	BIT(18)
+#define RP2_CHAN_STAT_RI_CHANGED_m	BIT(22)
+#define RP2_CHAN_STAT_TXEMPTY_m		BIT(25)
+
+#define RP2_CHAN_STAT_MS_CHANGED_MASK	(RP2_CHAN_STAT_DSR_CHANGED_m | \
+					 RP2_CHAN_STAT_CTS_CHANGED_m | \
+					 RP2_CHAN_STAT_CD_CHANGED_m | \
+					 RP2_CHAN_STAT_RI_CHANGED_m)
+
+#define RP2_TXRX_CTL			0x014
+#define RP2_TXRX_CTL_MSRIRQ_m		BIT(0)
+#define RP2_TXRX_CTL_RXIRQ_m		BIT(2)
+#define RP2_TXRX_CTL_RX_TRIG_s		3
+#define RP2_TXRX_CTL_RX_TRIG_m		(0x3 << RP2_TXRX_CTL_RX_TRIG_s)
+#define RP2_TXRX_CTL_RX_TRIG_1		(0x1 << RP2_TXRX_CTL_RX_TRIG_s)
+#define RP2_TXRX_CTL_RX_TRIG_256	(0x2 << RP2_TXRX_CTL_RX_TRIG_s)
+#define RP2_TXRX_CTL_RX_TRIG_448	(0x3 << RP2_TXRX_CTL_RX_TRIG_s)
+#define RP2_TXRX_CTL_RX_EN_m		BIT(5)
+#define RP2_TXRX_CTL_RTSFLOW_m		BIT(6)
+#define RP2_TXRX_CTL_DTRFLOW_m		BIT(7)
+#define RP2_TXRX_CTL_TX_TRIG_s		16
+#define RP2_TXRX_CTL_TX_TRIG_m		(0x3 << RP2_TXRX_CTL_RX_TRIG_s)
+#define RP2_TXRX_CTL_DSRFLOW_m		BIT(18)
+#define RP2_TXRX_CTL_TXIRQ_m		BIT(19)
+#define RP2_TXRX_CTL_CTSFLOW_m		BIT(23)
+#define RP2_TXRX_CTL_TX_EN_m		BIT(24)
+#define RP2_TXRX_CTL_RTS_m		BIT(25)
+#define RP2_TXRX_CTL_DTR_m		BIT(26)
+#define RP2_TXRX_CTL_LOOP_m		BIT(27)
+#define RP2_TXRX_CTL_BREAK_m		BIT(28)
+#define RP2_TXRX_CTL_CMSPAR_m		BIT(29)
+#define RP2_TXRX_CTL_nPARODD_m		BIT(30)
+#define RP2_TXRX_CTL_PARENB_m		BIT(31)
+
+#define RP2_UART_CTL			0x018
+#define RP2_UART_CTL_MODE_s		0
+#define RP2_UART_CTL_MODE_m		(0x7 << RP2_UART_CTL_MODE_s)
+#define RP2_UART_CTL_MODE_rs232		(0x1 << RP2_UART_CTL_MODE_s)
+#define RP2_UART_CTL_FLUSH_RX_m		BIT(3)
+#define RP2_UART_CTL_FLUSH_TX_m		BIT(4)
+#define RP2_UART_CTL_RESET_CH_m		BIT(5)
+#define RP2_UART_CTL_XMIT_EN_m		BIT(6)
+#define RP2_UART_CTL_DATABITS_s		8
+#define RP2_UART_CTL_DATABITS_m		(0x3 << RP2_UART_CTL_DATABITS_s)
+#define RP2_UART_CTL_DATABITS_8		(0x3 << RP2_UART_CTL_DATABITS_s)
+#define RP2_UART_CTL_DATABITS_7		(0x2 << RP2_UART_CTL_DATABITS_s)
+#define RP2_UART_CTL_DATABITS_6		(0x1 << RP2_UART_CTL_DATABITS_s)
+#define RP2_UART_CTL_DATABITS_5		(0x0 << RP2_UART_CTL_DATABITS_s)
+#define RP2_UART_CTL_STOPBITS_m		BIT(10)
+
+#define RP2_BAUD			0x01c
+
+/* ucode registers */
+#define RP2_TX_SWFLOW			0x02
+#define RP2_TX_SWFLOW_ena		0x81
+#define RP2_TX_SWFLOW_dis		0x9d
+
+#define RP2_RX_SWFLOW			0x0c
+#define RP2_RX_SWFLOW_ena		0x81
+#define RP2_RX_SWFLOW_dis		0x8d
+
+#define RP2_RX_FIFO			0x37
+#define RP2_RX_FIFO_ena			0x08
+#define RP2_RX_FIFO_dis			0x81
+
+static struct uart_driver rp2_uart_driver = {
+	.owner				= THIS_MODULE,
+	.driver_name			= DRV_NAME,
+	.dev_name			= "ttyRP",
+	.nr				= CONFIG_SERIAL_RP2_NR_UARTS,
+};
+
+struct rp2_card;
+
+struct rp2_uart_port {
+	struct uart_port		port;
+	int				idx;
+	int				ignore_rx;
+	struct rp2_card			*card;
+	void __iomem			*asic_base;
+	void __iomem			*base;
+	void __iomem			*ucode;
+};
+
+struct rp2_card {
+	struct pci_dev			*pdev;
+	struct rp2_uart_port		*ports;
+	int				n_ports;
+	int				initialized_ports;
+	int				minor_start;
+	int				smpte;
+	void __iomem			*bar0;
+	void __iomem			*bar1;
+	spinlock_t			card_lock;
+	struct completion		fw_loaded;
+};
+
+#define RP_ID(prod) PCI_VDEVICE(RP, (prod))
+#define RP_CAP(ports, smpte) (((ports) << 8) | ((smpte) << 0))
+
+static inline void rp2_decode_cap(const struct pci_device_id *id,
+				  int *ports, int *smpte)
+{
+	*ports = id->driver_data >> 8;
+	*smpte = id->driver_data & 0xff;
+}
+
+static DEFINE_SPINLOCK(rp2_minor_lock);
+static int rp2_minor_next;
+
+static int rp2_alloc_ports(int n_ports)
+{
+	int ret = -ENOSPC;
+
+	spin_lock(&rp2_minor_lock);
+	if (rp2_minor_next + n_ports <= CONFIG_SERIAL_RP2_NR_UARTS) {
+		/* sorry, no support for hot unplugging individual cards */
+		ret = rp2_minor_next;
+		rp2_minor_next += n_ports;
+	}
+	spin_unlock(&rp2_minor_lock);
+
+	return ret;
+}
+
+static inline struct rp2_uart_port *port_to_up(struct uart_port *port)
+{
+	return container_of(port, struct rp2_uart_port, port);
+}
+
+static void rp2_rmw(struct rp2_uart_port *up, int reg,
+		    u32 clr_bits, u32 set_bits)
+{
+	u32 tmp = readl(up->base + reg);
+	tmp &= ~clr_bits;
+	tmp |= set_bits;
+	writel(tmp, up->base + reg);
+}
+
+static void rp2_rmw_clr(struct rp2_uart_port *up, int reg, u32 val)
+{
+	rp2_rmw(up, reg, val, 0);
+}
+
+static void rp2_rmw_set(struct rp2_uart_port *up, int reg, u32 val)
+{
+	rp2_rmw(up, reg, 0, val);
+}
+
+static void rp2_mask_ch_irq(struct rp2_uart_port *up, int ch_num,
+			    int is_enabled)
+{
+	unsigned long flags, irq_mask;
+
+	spin_lock_irqsave(&up->card->card_lock, flags);
+
+	irq_mask = readl(up->asic_base + RP2_CH_IRQ_MASK);
+	if (is_enabled)
+		irq_mask &= ~BIT(ch_num);
+	else
+		irq_mask |= BIT(ch_num);
+	writel(irq_mask, up->asic_base + RP2_CH_IRQ_MASK);
+
+	spin_unlock_irqrestore(&up->card->card_lock, flags);
+}
+
+static unsigned int rp2_uart_tx_empty(struct uart_port *port)
+{
+	struct rp2_uart_port *up = port_to_up(port);
+	unsigned long tx_fifo_bytes, flags;
+
+	/*
+	 * This should probably check the transmitter, not the FIFO.
+	 * But the TXEMPTY bit doesn't seem to work unless the TX IRQ is
+	 * enabled.
+	 */
+	spin_lock_irqsave(&up->port.lock, flags);
+	tx_fifo_bytes = readw(up->base + RP2_TX_FIFO_COUNT);
+	spin_unlock_irqrestore(&up->port.lock, flags);
+
+	return tx_fifo_bytes ? 0 : TIOCSER_TEMT;
+}
+
+static unsigned int rp2_uart_get_mctrl(struct uart_port *port)
+{
+	struct rp2_uart_port *up = port_to_up(port);
+	u32 status;
+
+	status = readl(up->base + RP2_CHAN_STAT);
+	return ((status & RP2_CHAN_STAT_DCD_m) ? TIOCM_CAR : 0) |
+	       ((status & RP2_CHAN_STAT_DSR_m) ? TIOCM_DSR : 0) |
+	       ((status & RP2_CHAN_STAT_CTS_m) ? TIOCM_CTS : 0) |
+	       ((status & RP2_CHAN_STAT_RI_m) ? TIOCM_RI : 0);
+}
+
+static void rp2_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	rp2_rmw(port_to_up(port), RP2_TXRX_CTL,
+		RP2_TXRX_CTL_DTR_m | RP2_TXRX_CTL_RTS_m | RP2_TXRX_CTL_LOOP_m,
+		((mctrl & TIOCM_DTR) ? RP2_TXRX_CTL_DTR_m : 0) |
+		((mctrl & TIOCM_RTS) ? RP2_TXRX_CTL_RTS_m : 0) |
+		((mctrl & TIOCM_LOOP) ? RP2_TXRX_CTL_LOOP_m : 0));
+}
+
+static void rp2_uart_start_tx(struct uart_port *port)
+{
+	rp2_rmw_set(port_to_up(port), RP2_TXRX_CTL, RP2_TXRX_CTL_TXIRQ_m);
+}
+
+static void rp2_uart_stop_tx(struct uart_port *port)
+{
+	rp2_rmw_clr(port_to_up(port), RP2_TXRX_CTL, RP2_TXRX_CTL_TXIRQ_m);
+}
+
+static void rp2_uart_stop_rx(struct uart_port *port)
+{
+	rp2_rmw_clr(port_to_up(port), RP2_TXRX_CTL, RP2_TXRX_CTL_RXIRQ_m);
+}
+
+static void rp2_uart_break_ctl(struct uart_port *port, int break_state)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->lock, flags);
+	rp2_rmw(port_to_up(port), RP2_TXRX_CTL, RP2_TXRX_CTL_BREAK_m,
+		break_state ? RP2_TXRX_CTL_BREAK_m : 0);
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void rp2_uart_enable_ms(struct uart_port *port)
+{
+	rp2_rmw_set(port_to_up(port), RP2_TXRX_CTL, RP2_TXRX_CTL_MSRIRQ_m);
+}
+
+static void __rp2_uart_set_termios(struct rp2_uart_port *up,
+				   unsigned long cfl,
+				   unsigned long ifl,
+				   unsigned int baud_div)
+{
+	/* baud rate divisor (calculated elsewhere).  0 = divide-by-1 */
+	writew(baud_div - 1, up->base + RP2_BAUD);
+
+	/* data bits and stop bits */
+	rp2_rmw(up, RP2_UART_CTL,
+		RP2_UART_CTL_STOPBITS_m | RP2_UART_CTL_DATABITS_m,
+		((cfl & CSTOPB) ? RP2_UART_CTL_STOPBITS_m : 0) |
+		(((cfl & CSIZE) == CS8) ? RP2_UART_CTL_DATABITS_8 : 0) |
+		(((cfl & CSIZE) == CS7) ? RP2_UART_CTL_DATABITS_7 : 0) |
+		(((cfl & CSIZE) == CS6) ? RP2_UART_CTL_DATABITS_6 : 0) |
+		(((cfl & CSIZE) == CS5) ? RP2_UART_CTL_DATABITS_5 : 0));
+
+	/* parity and hardware flow control */
+	rp2_rmw(up, RP2_TXRX_CTL,
+		RP2_TXRX_CTL_PARENB_m | RP2_TXRX_CTL_nPARODD_m |
+		RP2_TXRX_CTL_CMSPAR_m | RP2_TXRX_CTL_DTRFLOW_m |
+		RP2_TXRX_CTL_DSRFLOW_m | RP2_TXRX_CTL_RTSFLOW_m |
+		RP2_TXRX_CTL_CTSFLOW_m,
+		((cfl & PARENB) ? RP2_TXRX_CTL_PARENB_m : 0) |
+		((cfl & PARODD) ? 0 : RP2_TXRX_CTL_nPARODD_m) |
+		((cfl & CMSPAR) ? RP2_TXRX_CTL_CMSPAR_m : 0) |
+		((cfl & CRTSCTS) ? (RP2_TXRX_CTL_RTSFLOW_m |
+				    RP2_TXRX_CTL_CTSFLOW_m) : 0));
+
+	/* XON/XOFF software flow control */
+	writeb((ifl & IXON) ? RP2_TX_SWFLOW_ena : RP2_TX_SWFLOW_dis,
+	       up->ucode + RP2_TX_SWFLOW);
+	writeb((ifl & IXOFF) ? RP2_RX_SWFLOW_ena : RP2_RX_SWFLOW_dis,
+	       up->ucode + RP2_RX_SWFLOW);
+}
+
+static void rp2_uart_set_termios(struct uart_port *port,
+				 struct ktermios *new,
+				 struct ktermios *old)
+{
+	struct rp2_uart_port *up = port_to_up(port);
+	unsigned long flags;
+	unsigned int baud, baud_div;
+
+	baud = uart_get_baud_rate(port, new, old, 0, port->uartclk / 16);
+	baud_div = uart_get_divisor(port, baud);
+
+	if (tty_termios_baud_rate(new))
+		tty_termios_encode_baud_rate(new, baud, baud);
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* ignore all characters if CREAD is not set */
+	port->ignore_status_mask = (new->c_cflag & CREAD) ? 0 : RP2_DUMMY_READ;
+
+	__rp2_uart_set_termios(up, new->c_cflag, new->c_iflag, baud_div);
+	uart_update_timeout(port, new->c_cflag, baud);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void rp2_rx_chars(struct rp2_uart_port *up)
+{
+	u16 bytes = readw(up->base + RP2_RX_FIFO_COUNT);
+	struct tty_struct *tty = tty_port_tty_get(&up->port.state->port);
+
+	if (!tty) {
+		/* Discard data: no tty available */
+		for (; bytes != 0; bytes--)
+			readw(up->base + RP2_DATA_BYTE);
+		return;
+	}
+
+	for (; bytes != 0; bytes--) {
+		u32 byte = readw(up->base + RP2_DATA_BYTE) | RP2_DUMMY_READ;
+		char ch = byte & 0xff;
+
+		if (likely(!(byte & RP2_DATA_BYTE_EXCEPTION_MASK))) {
+			if (!uart_handle_sysrq_char(&up->port, ch))
+				uart_insert_char(&up->port, byte, 0, ch,
+						 TTY_NORMAL);
+		} else {
+			char flag = TTY_NORMAL;
+
+			if (byte & RP2_DATA_BYTE_BREAK_m)
+				flag = TTY_BREAK;
+			else if (byte & RP2_DATA_BYTE_ERR_FRAMING_m)
+				flag = TTY_FRAME;
+			else if (byte & RP2_DATA_BYTE_ERR_PARITY_m)
+				flag = TTY_PARITY;
+			uart_insert_char(&up->port, byte,
+					 RP2_DATA_BYTE_ERR_OVERRUN_m, ch, flag);
+		}
+		up->port.icount.rx++;
+	}
+	tty_flip_buffer_push(tty);
+	tty_kref_put(tty);
+}
+
+static void rp2_tx_chars(struct rp2_uart_port *up)
+{
+	u16 max_tx = FIFO_SIZE - readw(up->base + RP2_TX_FIFO_COUNT);
+	struct circ_buf *xmit = &up->port.state->xmit;
+
+	if (uart_tx_stopped(&up->port)) {
+		rp2_uart_stop_tx(&up->port);
+		return;
+	}
+
+	for (; max_tx != 0; max_tx--) {
+		if (up->port.x_char) {
+			writeb(up->port.x_char, up->base + RP2_DATA_BYTE);
+			up->port.x_char = 0;
+			up->port.icount.tx++;
+			continue;
+		}
+		if (uart_circ_empty(xmit)) {
+			rp2_uart_stop_tx(&up->port);
+			break;
+		}
+		writeb(xmit->buf[xmit->tail], up->base + RP2_DATA_BYTE);
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		up->port.icount.tx++;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(&up->port);
+}
+
+static void rp2_ch_interrupt(struct rp2_uart_port *up)
+{
+	u32 status;
+
+	spin_lock(&up->port.lock);
+
+	/*
+	 * The IRQ status bits are clear-on-write.  Other status bits in
+	 * this register aren't, so it's harmless to write to them.
+	 */
+	status = readl(up->base + RP2_CHAN_STAT);
+	writel(status, up->base + RP2_CHAN_STAT);
+
+	if (status & RP2_CHAN_STAT_RXDATA_m)
+		rp2_rx_chars(up);
+	if (status & RP2_CHAN_STAT_TXEMPTY_m)
+		rp2_tx_chars(up);
+	if (status & RP2_CHAN_STAT_MS_CHANGED_MASK)
+		wake_up_interruptible(&up->port.state->port.delta_msr_wait);
+
+	spin_unlock(&up->port.lock);
+}
+
+static int rp2_asic_interrupt(struct rp2_card *card, unsigned int asic_id)
+{
+	void __iomem *base = card->bar1 + RP2_ASIC_OFFSET(asic_id);
+	int ch, handled = 0;
+	unsigned long status = readl(base + RP2_CH_IRQ_STAT) &
+			       ~readl(base + RP2_CH_IRQ_MASK);
+
+	for_each_set_bit(ch, &status, PORTS_PER_ASIC) {
+		rp2_ch_interrupt(&card->ports[ch]);
+		handled++;
+	}
+	return handled;
+}
+
+static irqreturn_t rp2_uart_interrupt(int irq, void *dev_id)
+{
+	struct rp2_card *card = dev_id;
+	int handled;
+
+	handled = rp2_asic_interrupt(card, 0);
+	if (card->n_ports >= PORTS_PER_ASIC)
+		handled += rp2_asic_interrupt(card, 1);
+
+	return handled ? IRQ_HANDLED : IRQ_NONE;
+}
+
+static inline void rp2_flush_fifos(struct rp2_uart_port *up)
+{
+	rp2_rmw_set(up, RP2_UART_CTL,
+		    RP2_UART_CTL_FLUSH_RX_m | RP2_UART_CTL_FLUSH_TX_m);
+	readl(up->base + RP2_UART_CTL);
+	udelay(10);
+	rp2_rmw_clr(up, RP2_UART_CTL,
+		    RP2_UART_CTL_FLUSH_RX_m | RP2_UART_CTL_FLUSH_TX_m);
+}
+
+static int rp2_uart_startup(struct uart_port *port)
+{
+	struct rp2_uart_port *up = port_to_up(port);
+
+	rp2_flush_fifos(up);
+	rp2_rmw(up, RP2_TXRX_CTL, RP2_TXRX_CTL_MSRIRQ_m, RP2_TXRX_CTL_RXIRQ_m);
+	rp2_rmw(up, RP2_TXRX_CTL, RP2_TXRX_CTL_RX_TRIG_m,
+		RP2_TXRX_CTL_RX_TRIG_1);
+	rp2_rmw(up, RP2_CHAN_STAT, 0, 0);
+	rp2_mask_ch_irq(up, up->idx, 1);
+
+	return 0;
+}
+
+static void rp2_uart_shutdown(struct uart_port *port)
+{
+	struct rp2_uart_port *up = port_to_up(port);
+	unsigned long flags;
+
+	rp2_uart_break_ctl(port, 0);
+
+	spin_lock_irqsave(&port->lock, flags);
+	rp2_mask_ch_irq(up, up->idx, 0);
+	rp2_rmw(up, RP2_CHAN_STAT, 0, 0);
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *rp2_uart_type(struct uart_port *port)
+{
+	return (port->type == PORT_RP2) ? "RocketPort 2 UART" : NULL;
+}
+
+static void rp2_uart_release_port(struct uart_port *port)
+{
+	/* Nothing to release ... */
+}
+
+static int rp2_uart_request_port(struct uart_port *port)
+{
+	/* UARTs always present */
+	return 0;
+}
+
+static void rp2_uart_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE)
+		port->type = PORT_RP2;
+}
+
+static int rp2_uart_verify_port(struct uart_port *port,
+				   struct serial_struct *ser)
+{
+	if (ser->type != PORT_UNKNOWN && ser->type != PORT_RP2)
+		return -EINVAL;
+
+	return 0;
+}
+
+static struct uart_ops rp2_uart_ops = {
+	.tx_empty	= rp2_uart_tx_empty,
+	.set_mctrl	= rp2_uart_set_mctrl,
+	.get_mctrl	= rp2_uart_get_mctrl,
+	.stop_tx	= rp2_uart_stop_tx,
+	.start_tx	= rp2_uart_start_tx,
+	.stop_rx	= rp2_uart_stop_rx,
+	.enable_ms	= rp2_uart_enable_ms,
+	.break_ctl	= rp2_uart_break_ctl,
+	.startup	= rp2_uart_startup,
+	.shutdown	= rp2_uart_shutdown,
+	.set_termios	= rp2_uart_set_termios,
+	.type		= rp2_uart_type,
+	.release_port	= rp2_uart_release_port,
+	.request_port	= rp2_uart_request_port,
+	.config_port	= rp2_uart_config_port,
+	.verify_port	= rp2_uart_verify_port,
+};
+
+static void rp2_reset_asic(struct rp2_card *card, unsigned int asic_id)
+{
+	void __iomem *base = card->bar1 + RP2_ASIC_OFFSET(asic_id);
+	u32 clk_cfg;
+
+	writew(1, base + RP2_GLOBAL_CMD);
+	readw(base + RP2_GLOBAL_CMD);
+	msleep(100);
+	writel(0, base + RP2_CLK_PRESCALER);
+
+	/* TDM clock configuration */
+	clk_cfg = readw(base + RP2_ASIC_CFG);
+	clk_cfg = (clk_cfg & ~BIT(8)) | BIT(9);
+	writew(clk_cfg, base + RP2_ASIC_CFG);
+
+	/* IRQ routing */
+	writel(ALL_PORTS_MASK, base + RP2_CH_IRQ_MASK);
+	writel(RP2_ASIC_IRQ_EN_m, base + RP2_ASIC_IRQ);
+}
+
+static void rp2_init_card(struct rp2_card *card)
+{
+	writel(4, card->bar0 + RP2_FPGA_CTL0);
+	writel(0, card->bar0 + RP2_FPGA_CTL1);
+
+	rp2_reset_asic(card, 0);
+	if (card->n_ports >= PORTS_PER_ASIC)
+		rp2_reset_asic(card, 1);
+
+	writel(RP2_IRQ_MASK_EN_m, card->bar0 + RP2_IRQ_MASK);
+}
+
+static void rp2_init_port(struct rp2_uart_port *up, const struct firmware *fw)
+{
+	int i;
+
+	writel(RP2_UART_CTL_RESET_CH_m, up->base + RP2_UART_CTL);
+	readl(up->base + RP2_UART_CTL);
+	udelay(1);
+
+	writel(0, up->base + RP2_TXRX_CTL);
+	writel(0, up->base + RP2_UART_CTL);
+	readl(up->base + RP2_UART_CTL);
+	udelay(1);
+
+	rp2_flush_fifos(up);
+
+	for (i = 0; i < min_t(int, fw->size, RP2_UCODE_BYTES); i++)
+		writeb(fw->data[i], up->ucode + i);
+
+	__rp2_uart_set_termios(up, CS8 | CREAD | CLOCAL, 0, DEFAULT_BAUD_DIV);
+	rp2_uart_set_mctrl(&up->port, 0);
+
+	writeb(RP2_RX_FIFO_ena, up->ucode + RP2_RX_FIFO);
+	rp2_rmw(up, RP2_UART_CTL, RP2_UART_CTL_MODE_m,
+		RP2_UART_CTL_XMIT_EN_m | RP2_UART_CTL_MODE_rs232);
+	rp2_rmw_set(up, RP2_TXRX_CTL,
+		    RP2_TXRX_CTL_TX_EN_m | RP2_TXRX_CTL_RX_EN_m);
+}
+
+static void rp2_fw_cb(const struct firmware *fw, void *context)
+{
+	struct rp2_card *card = context;
+	resource_size_t phys_base;
+	int i, rc = -ENOENT;
+
+	if (!fw) {
+		dev_err(&card->pdev->dev, "cannot find '%s' firmware image\n",
+			RP2_FW_NAME);
+		goto no_fw;
+	}
+
+	phys_base = pci_resource_start(card->pdev, 1);
+
+	for (i = 0; i < card->n_ports; i++) {
+		struct rp2_uart_port *rp = &card->ports[i];
+		struct uart_port *p;
+		int j = (unsigned)i % PORTS_PER_ASIC;
+
+		rp->asic_base = card->bar1;
+		rp->base = card->bar1 + RP2_PORT_BASE + j*RP2_PORT_SPACING;
+		rp->ucode = card->bar1 + RP2_UCODE_BASE + j*RP2_UCODE_SPACING;
+		rp->card = card;
+		rp->idx = j;
+
+		p = &rp->port;
+		p->line = card->minor_start + i;
+		p->dev = &card->pdev->dev;
+		p->type = PORT_RP2;
+		p->iotype = UPIO_MEM32;
+		p->uartclk = UART_CLOCK;
+		p->regshift = 2;
+		p->fifosize = FIFO_SIZE;
+		p->ops = &rp2_uart_ops;
+		p->irq = card->pdev->irq;
+		p->membase = rp->base;
+		p->mapbase = phys_base + RP2_PORT_BASE + j*RP2_PORT_SPACING;
+
+		if (i >= PORTS_PER_ASIC) {
+			rp->asic_base += RP2_ASIC_SPACING;
+			rp->base += RP2_ASIC_SPACING;
+			rp->ucode += RP2_ASIC_SPACING;
+			p->mapbase += RP2_ASIC_SPACING;
+		}
+
+		rp2_init_port(rp, fw);
+		rc = uart_add_one_port(&rp2_uart_driver, p);
+		if (rc) {
+			dev_err(&card->pdev->dev,
+				"error registering port %d: %d\n", i, rc);
+			break;
+		}
+		card->initialized_ports++;
+	}
+
+	release_firmware(fw);
+no_fw:
+	complete(&card->fw_loaded);
+
+	/*
+	 * rp2_fw_cb() is called from a workqueue long after rp2_probe()
+	 * has already returned success.  So if something failed here, we
+	 * need to manually yank the device.  This calls rp2_remove().
+	 */
+	if (rc)
+		device_release_driver(&card->pdev->dev);
+}
+
+static int rp2_probe(struct pci_dev *pdev,
+				   const struct pci_device_id *id)
+{
+	struct rp2_card *card;
+	struct rp2_uart_port *ports;
+	void __iomem * const *bars;
+	int rc;
+
+	card = devm_kzalloc(&pdev->dev, sizeof(*card), GFP_KERNEL);
+	if (!card)
+		return -ENOMEM;
+	pci_set_drvdata(pdev, card);
+	spin_lock_init(&card->card_lock);
+	init_completion(&card->fw_loaded);
+
+	rc = pcim_enable_device(pdev);
+	if (rc)
+		return rc;
+
+	rc = pcim_iomap_regions_request_all(pdev, 0x03, DRV_NAME);
+	if (rc)
+		return rc;
+
+	bars = pcim_iomap_table(pdev);
+	card->bar0 = bars[0];
+	card->bar1 = bars[1];
+	card->pdev = pdev;
+
+	rp2_decode_cap(id, &card->n_ports, &card->smpte);
+	dev_info(&pdev->dev, "found new card with %d ports\n", card->n_ports);
+
+	card->minor_start = rp2_alloc_ports(card->n_ports);
+	if (card->minor_start < 0) {
+		dev_err(&pdev->dev,
+			"too many ports (try increasing CONFIG_SERIAL_RP2_NR_UARTS)\n");
+		return -EINVAL;
+	}
+
+	rp2_init_card(card);
+
+	ports = devm_kzalloc(&pdev->dev, sizeof(*ports) * card->n_ports,
+			     GFP_KERNEL);
+	if (!ports)
+		return -ENOMEM;
+	card->ports = ports;
+
+	rc = devm_request_irq(&pdev->dev, pdev->irq, rp2_uart_interrupt,
+			      IRQF_SHARED, DRV_NAME, card);
+	if (rc)
+		return rc;
+
+	/*
+	 * Only catastrophic errors (e.g. ENOMEM) are reported here.
+	 * If the FW image is missing, we'll find out in rp2_fw_cb()
+	 * and print an error message.
+	 */
+	rc = request_firmware_nowait(THIS_MODULE, 1, RP2_FW_NAME, &pdev->dev,
+				     GFP_KERNEL, card, rp2_fw_cb);
+	if (rc)
+		return rc;
+	dev_dbg(&pdev->dev, "waiting for firmware blob...\n");
+
+	return 0;
+}
+
+static void rp2_remove(struct pci_dev *pdev)
+{
+	struct rp2_card *card = pci_get_drvdata(pdev);
+	int i;
+
+	wait_for_completion(&card->fw_loaded);
+	for (i = 0; i < card->initialized_ports; i++)
+		uart_remove_one_port(&rp2_uart_driver, &card->ports[i].port);
+}
+
+static DEFINE_PCI_DEVICE_TABLE(rp2_pci_tbl) = {
+
+	/* RocketPort INFINITY cards */
+
+	{ RP_ID(0x0040), RP_CAP(8,  0) }, /* INF Octa, RJ45, selectable */
+	{ RP_ID(0x0041), RP_CAP(32, 0) }, /* INF 32, ext interface */
+	{ RP_ID(0x0042), RP_CAP(8,  0) }, /* INF Octa, ext interface */
+	{ RP_ID(0x0043), RP_CAP(16, 0) }, /* INF 16, ext interface */
+	{ RP_ID(0x0044), RP_CAP(4,  0) }, /* INF Quad, DB, selectable */
+	{ RP_ID(0x0045), RP_CAP(8,  0) }, /* INF Octa, DB, selectable */
+	{ RP_ID(0x0046), RP_CAP(4,  0) }, /* INF Quad, ext interface */
+	{ RP_ID(0x0047), RP_CAP(4,  0) }, /* INF Quad, RJ45 */
+	{ RP_ID(0x004a), RP_CAP(4,  0) }, /* INF Plus, Quad */
+	{ RP_ID(0x004b), RP_CAP(8,  0) }, /* INF Plus, Octa */
+	{ RP_ID(0x004c), RP_CAP(8,  0) }, /* INF III, Octa */
+	{ RP_ID(0x004d), RP_CAP(4,  0) }, /* INF III, Quad */
+	{ RP_ID(0x004e), RP_CAP(2,  0) }, /* INF Plus, 2, RS232 */
+	{ RP_ID(0x004f), RP_CAP(2,  1) }, /* INF Plus, 2, SMPTE */
+	{ RP_ID(0x0050), RP_CAP(4,  0) }, /* INF Plus, Quad, RJ45 */
+	{ RP_ID(0x0051), RP_CAP(8,  0) }, /* INF Plus, Octa, RJ45 */
+	{ RP_ID(0x0052), RP_CAP(8,  1) }, /* INF Octa, SMPTE */
+
+	/* RocketPort EXPRESS cards */
+
+	{ RP_ID(0x0060), RP_CAP(8,  0) }, /* EXP Octa, RJ45, selectable */
+	{ RP_ID(0x0061), RP_CAP(32, 0) }, /* EXP 32, ext interface */
+	{ RP_ID(0x0062), RP_CAP(8,  0) }, /* EXP Octa, ext interface */
+	{ RP_ID(0x0063), RP_CAP(16, 0) }, /* EXP 16, ext interface */
+	{ RP_ID(0x0064), RP_CAP(4,  0) }, /* EXP Quad, DB, selectable */
+	{ RP_ID(0x0065), RP_CAP(8,  0) }, /* EXP Octa, DB, selectable */
+	{ RP_ID(0x0066), RP_CAP(4,  0) }, /* EXP Quad, ext interface */
+	{ RP_ID(0x0067), RP_CAP(4,  0) }, /* EXP Quad, RJ45 */
+	{ RP_ID(0x0068), RP_CAP(8,  0) }, /* EXP Octa, RJ11 */
+	{ RP_ID(0x0072), RP_CAP(8,  1) }, /* EXP Octa, SMPTE */
+	{ }
+};
+MODULE_DEVICE_TABLE(pci, rp2_pci_tbl);
+
+static struct pci_driver rp2_pci_driver = {
+	.name		= DRV_NAME,
+	.id_table	= rp2_pci_tbl,
+	.probe		= rp2_probe,
+	.remove		= rp2_remove,
+};
+
+static int __init rp2_uart_init(void)
+{
+	int rc;
+
+	rc = uart_register_driver(&rp2_uart_driver);
+	if (rc)
+		return rc;
+
+	rc = pci_register_driver(&rp2_pci_driver);
+	if (rc) {
+		uart_unregister_driver(&rp2_uart_driver);
+		return rc;
+	}
+
+	return 0;
+}
+
+static void __exit rp2_uart_exit(void)
+{
+	pci_unregister_driver(&rp2_pci_driver);
+	uart_unregister_driver(&rp2_uart_driver);
+}
+
+module_init(rp2_uart_init);
+module_exit(rp2_uart_exit);
+
+MODULE_DESCRIPTION("Comtrol RocketPort EXPRESS/INFINITY driver");
+MODULE_AUTHOR("Kevin Cernekee <cernekee@xxxxxxxxx>");
+MODULE_LICENSE("GPL v2");
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index 78f99d9..9dd47a5 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -219,4 +219,7 @@
 /* ARC (Synopsys) on-chip UART */
 #define PORT_ARC       101
 
+/* Rocketport EXPRESS/INFINITY */
+#define PORT_RP2	102
+
 #endif /* _UAPILINUX_SERIAL_CORE_H */
-- 
1.7.10.4

--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux