Hi,
On Saturday 06 October 2012 06:08 PM, Russell King - ARM Linux wrote:
Hi,
This series of patches fixes multiple flow control issues with the OMAP
serial driver, and prepares the driver for DMA engine conversion. We
require hardware assisted flow control to work properly for DMA support
otherwise we have no way to properly pause the transmitter.
This is generated against v3.6, and has been developed mainly by testing
on the OMAP4430 SDP platform.
Flow control seems to be really broken in the OMAP serial driver as things
stand today. It just about works with software flow control because the
generic serial core layer is inserting those characters, but only when the
legacy DMA support is not being used. Otherwise, flow control is
completely non-functional.
Issues identified in the OMAP serial driver are:
- set_mctrl() can only assert modem control lines, once asserted it
is not possible to deassert them.
- IXOFF controls sending of XON/XOFF characters, not the reception of
these sequences.
- IXON controls the recognition of XON/XOFF characters, not the transmission
of the same.
- Wrong bitmasks for hardware assisted software flow control. Bit 2
in EFR enables sending of XON2/XOFF2 which are never set.
- No point comparing received characters against XOFF2 ('special character
detect') as XOFF2 is not set.
- Fix multiple places where bits 6 and 5 of MCR are attempted to be
altered, but because EFR ECB is unset, these bits remain unaffected.
This effectively prevents us accessing the right XON/XOFF/TCR/TLR
registers.
- Remove unnecessary read-backs of EFR/MCR/LCR registers - these registers
don't change beneath us, they are configuration registers which hold their
values. Not only does this simplify the code, but it makes it more
readable, and more importantly ensures that we work from a consistent
state where ->efr never has ECB set, and ->mcr never has the TCRTLR
bit set.
- Fix disablement of hardware flow control and IXANY modes; once enabled
these could never be disabled because nothing in the code ever clears
these configuration bits.
Once that lot is fixed, these patches expand serial_core to permit hardware
assisted flow control by:
- adding throttle/unthrottle callbacks into low level serial drivers,
which allow them to take whatever action is necessary with hardware
assisted flow control to throttle the remote end. In the case of
OMAP serial, this means disabling the RX interrupts so that the FIFO
fills to the watermark.
We then have a number of cleanups to the OMAP serial code to make the
set_termios() function clearer and less prone to the kinds of mistakes
identified above. This results in a great simplification of the flow
control configuration code.
The OMAP serial driver hacks around with the transmit buffer allocation;
lets clean that up so that drivers can cleanly allocate their transmitter
buffer using coherent memory if that's what they desire.
Finally, the last few patches clean up the plat/omap-serial.h header file,
moving most of its contents into the OMAP serial driver itself. Most of
this is private to the OMAP serial driver and should never have been
shared with anything else.
I have omitted to include the conversion of the transmit paths to DMA
engine. Even with all the above fixed, it has issues when DMA transmit
is in progress, and a program issues a TCSETS call (as `less' does after
it has written its prompt.) At the moment, this causes lots of junk to
be emitted from the serial port when issuing `dmesg | less' which sometimes
brings the port to a complete halt.
As the OMAP DMA hardware does not have a clean pause when performing a
MEM->DEV transfer (it discards its FIFO) I do not see a solution to this,
which probably means that we can _not_ ever support transmit DMA on OMAP
platforms.
This means the xmit buffer allocation patches are not that useful unless
a solution to that can be found.
Now, the remaining question is, how much of this patch set do we think
about merging, and when. Given that flow control in this driver has been
broken for a very long time, and no one has apparantly noticed, I don't
think there's any urgency to this, so given its size, my preference would
be to queue it up for the next merge window. The thing that would worry
me about applying some of the initial patches is that they may change
the behaviour today and make any problems here more visible.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Boot Tested this patch series against v3.6 tag(applied cleanly) on panda
board and
PM tested(hitting off in Idle and suspend) on omap3630 based beagle board.
Note, I also tested the patches against the current master but only
after rebasing, since the current master includes serial patches from
Felipe Balbi[1].
[1] https://lkml.org/lkml/2012/8/24/139
Tested-by: Sourav Poddar <sourav.poddar@xxxxxx>
Thanks,
Sourav
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
