Converting uart driver to adapt to pm runtime API's.
Code re-org + cleanup.
Moving some functionality from serial.c to omap-serial.c
Changes involves:
================
1.) Cleaning up certain uart calls from sram_idle func.
2.) Removed all types of uart clock handling code from serial.c
3.) Using hwmod_mux API enable wakeup capability for uart pad during
hwmod_idle state i.e., when uart clocks are disabled we can enable
io-pad wakeup capability for uart if mux_data is available for
given uart. Also during during resume from idle call to uart we need
to enable clocks back conditionally and this can be done only when io-pad
wakeup event bit is set for uart_rx pad. So we need a hwmod API
which can probe the uart pad and let us know whether a uart wakeup
happened. So omap_hmwod_pad_wakeup_status API is added to meet this
requirement.
3.) Adapted omap-serial driver to use runtime API's.
4.) Modify serial_init calls to accept uart parameters from board file.
Like dma_usage, rx_timeout, dma_rx_pollrate, auto_suspend_timeout etc.
5.) Use the omap_prm driver with irq_chaining to wake up uart after clocks are
cut.
Patch series is based on 3.2-rc1.
Patch series depends on *Tero's v9 Irq_chaining patches*.
Dependent irq_chaining patches are as below.
89ac62b omap3+: add omap prm driver initialization
170431f OMAP3: pm: do not enable PRCM MPU interrupts manually
9aba1b0 omap3: pm: use prcm chain handler
435481f OMAP2+: mux: add support for PAD wakeup interrupts
5b2d361 mfd: omap-prm: added suspend prepare and complete callbacks
aa55c41 mfd: omap-prm: added chain interrupt handler
d1db904 mfd: omap-prm: add driver skeleton
31d056c TEMP: OMAP4xxx: hwmod data: add PRM hwmod
19ec3bc TEMP: OMAP3xxx: hwmod data: add PRM hwmod
9a89688 OMAP2+: hwmod: Add API to check IO PAD wakeup status
78e8b65 OMAP2+: hwmod: Add API to enable IO ring wakeup.
Same combination is hosted at:
git://gitorious.org/runtime_3-0/runtime_3-0.git 3.2-rc1_uart_runtime
Ensure CONFIG_OMAP_PRM is set while testing irq_chaining with uart.
And for pm_qos usage ensure CONFIG_CPU_IDLE is selected other wise
console might be sluggish.
Changes from v7:
---------------
http://www.mail-archive.com/linux-omap@xxxxxxxxxxxxxxx/msg57804.html
http://www.mail-archive.com/linux-omap@xxxxxxxxxxxxxxx/msg58209.html
http://www.spinics.net/lists/linux-omap/msg59978.html
http://www.spinics.net/lists/linux-serial/msg04772.html
Testing updates:
----------------
OMAP2420/2430SDP: Boot tested.
OMAP3430SDP:
retention, off_mode, system_wide suspend is tested.
(earlyprintk & no_console_suspend checked)
OMAP3630 - Zoom3:
pm-retention checked with quart/omap-uart3
[Also tested with uart3 as console uart and pm-ret checked]
BeagleBoard XM Rev C(3630):
retention, off_mode, system_wide suspend is tested.
Deepak K (1):
OMAP2+: UART: Allow UART parameters to be configured from board file.
Govindraj.R (18):
OMAP2+: UART: cleanup + remove uart pm specific API
OMAP2+: UART: cleanup 8250 console driver support
OMAP2+: UART: Cleanup part of clock gating mechanism for uart
OMAP2+: UART: Add default mux for all uarts.
OMAP2+: UART: Remove mapbase/membase fields from pdata.
OMAP2+: UART: Add runtime pm support for omap-serial driver
OMAP2+: UART: Remove context_save and move context restore to driver
OMAP2+: UART: Ensure all reg values configured are available from
port structure
OMAP2+: UART: Remove uart reset function.
OMAP2+: UART: Get context loss count to context restore
OMAP2+: UART: Move errata handling from serial.c to omap-serial
OMAP2+: UART: Add wakeup mechanism for omap-uarts
OMAP2+: UART: Remove old and unused clocks handling funcs
OMAP2+: UART: remove temporary variable used to count uart instance
OMAP2+: UART: Use custom activate func for console uart.
OMAP2+: UART: Avoid uart idling on suspend for no_console_suspend
usecase
OMAP2+: UART: Do not gate uart clocks if used for debug_prints
OMAP2+: UART: Remove omap_uart_can_sleep and add pm_qos
Jon Hunter (1):
OMAP2+: UART: Make the RX_TIMEOUT for DMA configurable for each UART
arch/arm/mach-omap2/board-3430sdp.c | 100 +---
arch/arm/mach-omap2/board-4430sdp.c | 68 +--
arch/arm/mach-omap2/board-n8x0.c | 6 +-
arch/arm/mach-omap2/board-omap4panda.c | 68 +--
arch/arm/mach-omap2/cpuidle34xx.c | 5 -
arch/arm/mach-omap2/pm24xx.c | 20 -
arch/arm/mach-omap2/pm34xx.c | 42 --
arch/arm/mach-omap2/serial.c | 926 +++++++------------------
arch/arm/plat-omap/include/plat/omap-serial.h | 36 +-
arch/arm/plat-omap/include/plat/serial.h | 10 +-
drivers/tty/serial/omap-serial.c | 341 ++++++++--
11 files changed, 607 insertions(+), 1015 deletions(-)
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
