There's no need to run the cmd->done callback for aborted commands. Remove
the old EH code and the RESET_RUN_DONE macro.
Signed-off-by: Finn Thain <fthain@xxxxxxxxxxxxxxxxxxx>
Reviewed-by: Hannes Reinecke <hare@xxxxxxx>
Tested-by: Michael Schmitz <schmitzmic@xxxxxxxxx>
---
drivers/scsi/atari_NCR5380.c | 88 -------------------------------------------
drivers/scsi/sun3_scsi.c | 1
2 files changed, 89 deletions(-)
Index: linux/drivers/scsi/atari_NCR5380.c
===================================================================
--- linux.orig/drivers/scsi/atari_NCR5380.c 2014-11-12 16:11:42.000000000 +1100
+++ linux/drivers/scsi/atari_NCR5380.c 2014-11-12 16:11:43.000000000 +1100
@@ -2877,9 +2877,6 @@ static int NCR5380_bus_reset(struct scsi
struct NCR5380_hostdata *hostdata = shost_priv(instance);
int i;
unsigned long flags;
-#if defined(RESET_RUN_DONE)
- struct scsi_cmnd *connected, *disconnected_queue;
-#endif
NCR5380_print_status(instance);
@@ -2898,89 +2895,6 @@ static int NCR5380_bus_reset(struct scsi
* through anymore ... */
(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- /* MSch 20140115 - looking at the generic NCR5380 driver, all of this
- * should go.
- * Catch-22: if we don't clear all queues, the SCSI driver lock will
- * not be reset by atari_scsi_reset()!
- */
-
-#if defined(RESET_RUN_DONE)
- /* XXX Should now be done by midlevel code, but it's broken XXX */
- /* XXX see below XXX */
-
- /* MSch: old-style reset: actually abort all command processing here */
-
- /* After the reset, there are no more connected or disconnected commands
- * and no busy units; to avoid problems with re-inserting the commands
- * into the issue_queue (via scsi_done()), the aborted commands are
- * remembered in local variables first.
- */
- local_irq_save(flags);
- connected = (struct scsi_cmnd *)hostdata->connected;
- hostdata->connected = NULL;
- disconnected_queue = (struct scsi_cmnd *)hostdata->disconnected_queue;
- hostdata->disconnected_queue = NULL;
-#ifdef SUPPORT_TAGS
- free_all_tags();
-#endif
- for (i = 0; i < 8; ++i)
- hostdata->busy[i] = 0;
-#ifdef REAL_DMA
- hostdata->dma_len = 0;
-#endif
- local_irq_restore(flags);
-
- /* In order to tell the mid-level code which commands were aborted,
- * set the command status to DID_RESET and call scsi_done() !!!
- * This ultimately aborts processing of these commands in the mid-level.
- */
-
- if ((cmd = connected)) {
- dprintk(NDEBUG_ABORT, "scsi%d: reset aborted a connected command\n", H_NO(cmd));
- cmd->result = (cmd->result & 0xffff) | (DID_RESET << 16);
- cmd->scsi_done(cmd);
- }
-
- for (i = 0; (cmd = disconnected_queue); ++i) {
- disconnected_queue = NEXT(cmd);
- SET_NEXT(cmd, NULL);
- cmd->result = (cmd->result & 0xffff) | (DID_RESET << 16);
- cmd->scsi_done(cmd);
- }
- if (i > 0)
- dprintk(NDEBUG_ABORT, "scsi: reset aborted %d disconnected command(s)\n", i);
-
- /* The Falcon lock should be released after a reset...
- */
- /* ++guenther: moved to atari_scsi_reset(), to prevent a race between
- * unlocking and enabling dma interrupt.
- */
-/* falcon_release_lock_if_possible( hostdata );*/
-
- /* since all commands have been explicitly terminated, we need to tell
- * the midlevel code that the reset was SUCCESSFUL, and there is no
- * need to 'wake up' the commands by a request_sense
- */
- return SUCCESS;
-#else /* 1 */
-
- /* MSch: new-style reset handling: let the mid-level do what it can */
-
- /* ++guenther: MID-LEVEL IS STILL BROKEN.
- * Mid-level is supposed to requeue all commands that were active on the
- * various low-level queues. In fact it does this, but that's not enough
- * because all these commands are subject to timeout. And if a timeout
- * happens for any removed command, *_abort() is called but all queues
- * are now empty. Abort then gives up the falcon lock, which is fatal,
- * since the mid-level will queue more commands and must have the lock
- * (it's all happening inside timer interrupt handler!!).
- * Even worse, abort will return NOT_RUNNING for all those commands not
- * on any queue, so they won't be retried ...
- *
- * Conclusion: either scsi.c disables timeout for all resetted commands
- * immediately, or we lose! As of linux-2.0.20 it doesn't.
- */
-
/* After the reset, there are no more connected or disconnected commands
* and no busy units; so clear the low-level status here to avoid
* conflicts when the mid-level code tries to wake up the affected
@@ -3010,7 +2924,5 @@ static int NCR5380_bus_reset(struct scsi
maybe_release_dma_irq(instance);
local_irq_restore(flags);
- /* we did no complete reset of all commands, so a wakeup is required */
return SUCCESS;
-#endif /* 1 */
}
Index: linux/drivers/scsi/sun3_scsi.c
===================================================================
--- linux.orig/drivers/scsi/sun3_scsi.c 2014-11-12 16:11:39.000000000 +1100
+++ linux/drivers/scsi/sun3_scsi.c 2014-11-12 16:11:43.000000000 +1100
@@ -39,7 +39,6 @@
/* Definitions for the core NCR5380 driver. */
#define REAL_DMA
-#define RESET_RUN_DONE
/* #define SUPPORT_TAGS */
/* minimum number of bytes to do dma on */
#define DMA_MIN_SIZE 129
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
