Hi,
The proposed fix fixes the timeout crash.
In normal operation the patch works, so after applying the fix you can add
my Tested-By.
One additional minor fix that is required:
In ufshcd_link_startup the following print-out is printed in success as well:
dev_err(hba->dev, "link startup failed %d\n", ret);
Please move it to the error cases only.
Thanks,
Maya
> On 5/6/2013 11:07 AM, Seungwon Jeon wrote:
>> Link start-up requires long time with multiphase handshakes
>> between UFS host and device. This affects driver's probe time.
>> This patch let link start-up run asynchronously. Link start-up
>> will be executed at the end of prove separately.
>> Along with this change, the following is worked.
>>
>> Defined completion time of uic command to avoid a permanent wait.
> We have seen a kernel crash when the timeout happens in our internal
> testing. This is basically because the the UIC_CMD_TIMEOUT of 500msec is
> less for our platform. We see UIC_COMMAND_COMPL interrupt after this
> timeout and since uic_cmd is freed we see a kernel crash.
>
> [ 6.026094] ufshcd 0000:01:00.0: link startup: error code -110
> [ 6.030886] ufshcd 0000:01:00.0: link startup failed -110
> ...
>
> [ 6.487288] BUG: spinlock bad magic on CPU#0, swapper/0/0
> [ 6.491683] Unable to handle kernel paging request at virtual address
> 6000012b
> ...
> [ 7.625270] [<c07c3718>] (spin_dump+0x4c/0x88) from [<c02ab9d8>]
> (do_raw_spin_lock+0x20/0x154)
> [ 7.633877] [<c02ab9d8>] (do_raw_spin_lock+0x20/0x154) from
> [<c07ccba4>] (_raw_spin_lock_irqsave+0x28/0x30)
> [ 7.643583] [<c07ccba4>] (_raw_spin_lock_irqsave+0x28/0x30) from
> [<c00a3c98>] (complete+0x1c/0x58)
> [ 7.652525] [<c00a3c98>] (complete+0x1c/0x58) from [<c03d10c4>]
> (ufshcd_intr+0x1a8/0x498)
> [ 7.660705] [<c03d10c4>] (ufshcd_intr+0x1a8/0x498) from [<c00cff48>]
> (handle_irq_event_percpu+0xb0/0x290)
> [ 7.670227] [<c00cff48>] (handle_irq_event_percpu+0xb0/0x290) from
> [<c00d0164>] (handle_irq_event+0x3c/0x5c)
> [ 7.680054] [<c00d0164>] (handle_irq_event+0x3c/0x5c) from
> [<c00d2c50>] (handle_fasteoi_irq+0xdc/0x148)
> [ 7.689424] [<c00d2c50>] (handle_fasteoi_irq+0xdc/0x148) from
> [<c00cf7ac>] (generic_handle_irq+0x30/0x44)
> [ 7.698977] [<c00cf7ac>] (generic_handle_irq+0x30/0x44) from
> [<c000ee40>] (handle_IRQ+0x7c/0xc0)
> [ 7.707736] [<c000ee40>] (handle_IRQ+0x7c/0xc0) from [<c0008620>]
> (gic_handle_irq+0x94/0x110)
> [ 7.716252] [<c0008620>] (gic_handle_irq+0x94/0x110) from
> [<c07ccec0>] (__irq_svc+0x40/0x70)
>
>
> Following would fix this. Please check. Also, we need to increase the
> timeout to say 5 secs to avoid such races.
>
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index ecbae40..ae22a8e 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -485,6 +485,7 @@ static int
> ufshcd_wait_for_uic_cmd(struct ufs_hba *hba, struct uic_command *uic_cmd)
> {
> int ret;
> + unsigned long flags;
>
> if (wait_for_completion_timeout(&uic_cmd->done,
> msecs_to_jiffies(UIC_CMD_TIMEOUT)))
> @@ -492,6 +493,10 @@ ufshcd_wait_for_uic_cmd(struct ufs_hba *hba, struct
> uic_command *uic_cmd)
> else
> ret = -ETIMEDOUT;
>
> + spin_lock_irqsave(hba->host->host_lock, flags);
> + hba->active_uic_cmd = NULL;
> + spin_unlock_irqrestore(hba->host->host_lock, flags);
> +
> return ret;
> }
>
> @@ -1842,7 +1847,7 @@ ufshcd_transfer_rsp_status(struct ufs_hba *hba,
> struct ufshcd_lrb *lrbp)
> */
> static void ufshcd_uic_cmd_compl(struct ufs_hba *hba, u32 intr_status)
> {
> - if (intr_status & UIC_COMMAND_COMPL) {
> + if (hba->active_uic_cmd && (intr_status & UIC_COMMAND_COMPL)) {
> hba->active_uic_cmd->argument2 |=
> ufshcd_get_uic_cmd_result(hba);
> hba->active_uic_cmd->argument3 =
>
>
>> Added mutex to guarantee of uic command at a time.
>> Adapted some sequence of controller initialization after link statup
>> according to HCI standard.
>>
>> Signed-off-by: Seungwon Jeon <tgih.jun@xxxxxxxxxxx>
>> Signed-off-by: Sujit Reddy Thumma <sthumma@xxxxxxxxxxxxxx>
>> ---
>> drivers/scsi/ufs/ufshcd.c | 287
>> ++++++++++++++++++++++++++++++---------------
>> drivers/scsi/ufs/ufshcd.h | 10 +-
>> 2 files changed, 200 insertions(+), 97 deletions(-)
>>
>> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
>> index e04c74e..118f104 100644
>> --- a/drivers/scsi/ufs/ufshcd.c
>> +++ b/drivers/scsi/ufs/ufshcd.c
>> @@ -33,11 +33,15 @@
>> * this program.
>> */
>>
>> +#include <linux/async.h>
>> +
>> #include "ufshcd.h"
>>
>> #define UFSHCD_ENABLE_INTRS (UTP_TRANSFER_REQ_COMPL |\
>> UTP_TASK_REQ_COMPL |\
>> UFSHCD_ERROR_MASK)
>> +/* UIC command timeout, unit: ms */
>> +#define UIC_CMD_TIMEOUT 500
>>
>> enum {
>> UFSHCD_MAX_CHANNEL = 0,
>> @@ -401,24 +405,115 @@ static inline void ufshcd_hba_capabilities(struct
>> ufs_hba *hba)
>> }
>>
>> /**
>> - * ufshcd_send_uic_command - Send UIC commands to unipro layers
>> + * ufshcd_ready_for_uic_cmd - Check if controller is ready
>> + * to accept UIC commands
>> * @hba: per adapter instance
>> - * @uic_command: UIC command
>> + * Return true on success, else false
>> + */
>> +static inline bool ufshcd_ready_for_uic_cmd(struct ufs_hba *hba)
>> +{
>> + if (ufshcd_readl(hba, REG_CONTROLLER_STATUS) & UIC_COMMAND_READY)
>> + return true;
>> + else
>> + return false;
>> +}
>> +
>> +/**
>> + * ufshcd_dispatch_uic_cmd - Dispatch UIC commands to unipro layers
>> + * @hba: per adapter instance
>> + * @uic_cmd: UIC command
>> + *
>> + * Mutex must be held.
>> */
>> static inline void
>> -ufshcd_send_uic_command(struct ufs_hba *hba, struct uic_command
>> *uic_cmnd)
>> +ufshcd_dispatch_uic_cmd(struct ufs_hba *hba, struct uic_command
>> *uic_cmd)
>> {
>> + hba->active_uic_cmd = uic_cmd;
>> +
>> /* Write Args */
>> - ufshcd_writel(hba, uic_cmnd->argument1, REG_UIC_COMMAND_ARG_1);
>> - ufshcd_writel(hba, uic_cmnd->argument2, REG_UIC_COMMAND_ARG_2);
>> - ufshcd_writel(hba, uic_cmnd->argument3, REG_UIC_COMMAND_ARG_3);
>> + ufshcd_writel(hba, uic_cmd->argument1, REG_UIC_COMMAND_ARG_1);
>> + ufshcd_writel(hba, uic_cmd->argument2, REG_UIC_COMMAND_ARG_2);
>> + ufshcd_writel(hba, uic_cmd->argument3, REG_UIC_COMMAND_ARG_3);
>>
>> /* Write UIC Cmd */
>> - ufshcd_writel(hba, uic_cmnd->command & COMMAND_OPCODE_MASK,
>> + ufshcd_writel(hba, uic_cmd->command & COMMAND_OPCODE_MASK,
>> REG_UIC_COMMAND);
>> }
>>
>> /**
>> + * ufshcd_wait_for_uic_cmd - Wait complectioin of UIC command
>> + * @hba: per adapter instance
>> + * @uic_command: UIC command
>> + *
>> + * Must be called with mutex held.
>> + * Returns 0 only if success.
>> + */
>> +static int
>> +ufshcd_wait_for_uic_cmd(struct ufs_hba *hba, struct uic_command
>> *uic_cmd)
>> +{
>> + int ret;
>> +
>> + if (wait_for_completion_timeout(&uic_cmd->done,
>> + msecs_to_jiffies(UIC_CMD_TIMEOUT)))
>> + ret = uic_cmd->argument2 & MASK_UIC_COMMAND_RESULT;
>> + else
>> + ret = -ETIMEDOUT;
>> +
>> + return ret;
>> +}
>> +
>> +/**
>> + * __ufshcd_send_uic_cmd - Send UIC commands and retrieve the result
>> + * @hba: per adapter instance
>> + * @uic_cmd: UIC command
>> + *
>> + * Identical to ufshcd_send_uic_cmd() expect mutex. Must be called
>> + * with mutex held.
>> + * Returns 0 only if success.
>> + */
>> +static int
>> +__ufshcd_send_uic_cmd(struct ufs_hba *hba, struct uic_command *uic_cmd)
>> +{
>> + int ret;
>> + unsigned long flags;
>> +
>> + if (!ufshcd_ready_for_uic_cmd(hba)) {
>> + dev_err(hba->dev,
>> + "Controller not ready to accept UIC commands\n");
>> + return -EIO;
>> + }
>> +
>> + init_completion(&uic_cmd->done);
>> +
>> + spin_lock_irqsave(hba->host->host_lock, flags);
>> + ufshcd_dispatch_uic_cmd(hba, uic_cmd);
>> + spin_unlock_irqrestore(hba->host->host_lock, flags);
>> +
>> + ret = ufshcd_wait_for_uic_cmd(hba, uic_cmd);
>> +
>> + return ret;
>> +}
>> +
>> +/**
>> + * ufshcd_send_uic_cmd - Send UIC commands and retrieve the result
>> + * @hba: per adapter instance
>> + * @uic_cmd: UIC command
>> + *
>> + * Returns 0 only if success.
>> + */
>> +static int
>> +ufshcd_send_uic_cmd(struct ufs_hba *hba, struct uic_command *uic_cmd)
>> +{
>> + int ret;
>> +
>> + mutex_lock(&hba->uic_cmd_mutex);
>> + ret = __ufshcd_send_uic_cmd(hba, uic_cmd);
>> + mutex_unlock(&hba->uic_cmd_mutex);
>> +
>> + return ret;
>> +}
>> +
>> +/**
>> * ufshcd_map_sg - Map scatter-gather list to prdt
>> * @lrbp - pointer to local reference block
>> *
>> @@ -962,34 +1057,16 @@ static void ufshcd_host_memory_configure(struct
>> ufs_hba *hba)
>> */
>> static int ufshcd_dme_link_startup(struct ufs_hba *hba)
>> {
>> - struct uic_command *uic_cmd;
>> - unsigned long flags;
>> + struct uic_command uic_cmd = {0};
>> + int ret;
>>
>> - /* check if controller is ready to accept UIC commands */
>> - if ((ufshcd_readl(hba, REG_CONTROLLER_STATUS) &
>> - UIC_COMMAND_READY) == 0x0) {
>> - dev_err(hba->dev,
>> - "Controller not ready"
>> - " to accept UIC commands\n");
>> - return -EIO;
>> - }
>> -
>> - spin_lock_irqsave(hba->host->host_lock, flags);
>> + uic_cmd.command = UIC_CMD_DME_LINK_STARTUP;
>>
>> - /* form UIC command */
>> - uic_cmd = &hba->active_uic_cmd;
>> - uic_cmd->command = UIC_CMD_DME_LINK_STARTUP;
>> - uic_cmd->argument1 = 0;
>> - uic_cmd->argument2 = 0;
>> - uic_cmd->argument3 = 0;
>> -
>> - /* enable UIC related interrupts */
>> - ufshcd_enable_intr(hba, UIC_COMMAND_COMPL);
>> -
>> - /* sending UIC commands to controller */
>> - ufshcd_send_uic_command(hba, uic_cmd);
>> - spin_unlock_irqrestore(hba->host->host_lock, flags);
>> - return 0;
>> + ret = ufshcd_send_uic_cmd(hba, &uic_cmd);
>> + if (ret)
>> + dev_err(hba->dev,
>> + "link startup: error code %d\n", ret);
>> + return ret;
>> }
>>
>> /**
>> @@ -998,9 +1075,10 @@ static int ufshcd_dme_link_startup(struct ufs_hba
>> *hba)
>> *
>> * To bring UFS host controller to operational state,
>> * 1. Check if device is present
>> - * 2. Configure run-stop-registers
>> - * 3. Enable required interrupts
>> - * 4. Configure interrupt aggregation
>> + * 2. Enable required interrupts
>> + * 3. Configure interrupt aggregation
>> + * 4. Program UTRL and UTMRL base addres
>> + * 5. Configure run-stop-registers
>> *
>> * Returns 0 on success, non-zero value on failure
>> */
>> @@ -1017,6 +1095,22 @@ static int ufshcd_make_hba_operational(struct
>> ufs_hba *hba)
>> goto out;
>> }
>>
>> + /* Enable required interrupts */
>> + ufshcd_enable_intr(hba, UFSHCD_ENABLE_INTRS);
>> +
>> + /* Configure interrupt aggregation */
>> + ufshcd_config_int_aggr(hba, INT_AGGR_CONFIG);
>> +
>> + /* Configure UTRL and UTMRL base address registers */
>> + ufshcd_writel(hba, lower_32_bits(hba->utrdl_dma_addr),
>> + REG_UTP_TRANSFER_REQ_LIST_BASE_L);
>> + ufshcd_writel(hba, upper_32_bits(hba->utrdl_dma_addr),
>> + REG_UTP_TRANSFER_REQ_LIST_BASE_H);
>> + ufshcd_writel(hba, lower_32_bits(hba->utmrdl_dma_addr),
>> + REG_UTP_TASK_REQ_LIST_BASE_L);
>> + ufshcd_writel(hba, upper_32_bits(hba->utmrdl_dma_addr),
>> + REG_UTP_TASK_REQ_LIST_BASE_H);
>> +
>> /*
>> * UCRDY, UTMRLDY and UTRLRDY bits must be 1
>> * DEI, HEI bits must be 0
>> @@ -1030,17 +1124,11 @@ static int ufshcd_make_hba_operational(struct
>> ufs_hba *hba)
>> goto out;
>> }
>>
>> - /* Enable required interrupts */
>> - ufshcd_enable_intr(hba, UFSHCD_ENABLE_INTRS);
>> -
>> - /* Configure interrupt aggregation */
>> - ufshcd_config_int_aggr(hba, INT_AGGR_CONFIG);
>> -
>> if (hba->ufshcd_state == UFSHCD_STATE_RESET)
>> scsi_unblock_requests(hba->host);
>>
>> hba->ufshcd_state = UFSHCD_STATE_OPERATIONAL;
>> - scsi_scan_host(hba->host);
>> +
>> out:
>> return err;
>> }
>> @@ -1109,34 +1197,29 @@ static int ufshcd_hba_enable(struct ufs_hba
>> *hba)
>> }
>>
>> /**
>> - * ufshcd_initialize_hba - start the initialization process
>> + * ufshcd_link_startup - Initialize unipro link startup
>> * @hba: per adapter instance
>> *
>> - * 1. Enable the controller via ufshcd_hba_enable.
>> - * 2. Program the Transfer Request List Address with the starting
>> address of
>> - * UTRDL.
>> - * 3. Program the Task Management Request List Address with starting
>> address
>> - * of UTMRDL.
>> - *
>> - * Returns 0 on success, non-zero value on failure.
>> + * Returns 0 for success, non-zero in case of failure
>> */
>> -static int ufshcd_initialize_hba(struct ufs_hba *hba)
>> +static int ufshcd_link_startup(struct ufs_hba *hba)
>> {
>> - if (ufshcd_hba_enable(hba))
>> - return -EIO;
>> + int ret;
>>
>> - /* Configure UTRL and UTMRL base address registers */
>> - ufshcd_writel(hba, lower_32_bits(hba->utrdl_dma_addr),
>> - REG_UTP_TRANSFER_REQ_LIST_BASE_L);
>> - ufshcd_writel(hba, upper_32_bits(hba->utrdl_dma_addr),
>> - REG_UTP_TRANSFER_REQ_LIST_BASE_H);
>> - ufshcd_writel(hba, lower_32_bits(hba->utmrdl_dma_addr),
>> - REG_UTP_TASK_REQ_LIST_BASE_L);
>> - ufshcd_writel(hba, upper_32_bits(hba->utmrdl_dma_addr),
>> - REG_UTP_TASK_REQ_LIST_BASE_H);
>> + /* enable UIC related interrupts */
>> + ufshcd_enable_intr(hba, UIC_COMMAND_COMPL);
>> +
>> + ret = ufshcd_dme_link_startup(hba);
>> + if (ret)
>> + goto out;
>>
>> - /* Initialize unipro link startup procedure */
>> - return ufshcd_dme_link_startup(hba);
>> + ret = ufshcd_make_hba_operational(hba);
>> + if (ret)
>> + goto out;
>> +
>> +out:
>> + dev_err(hba->dev, "link startup failed %d\n", ret);
>> + return ret;
>> }
>>
>> /**
>> @@ -1176,12 +1259,19 @@ static int ufshcd_do_reset(struct ufs_hba *hba)
>> hba->outstanding_reqs = 0;
>> hba->outstanding_tasks = 0;
>>
>> - /* start the initialization process */
>> - if (ufshcd_initialize_hba(hba)) {
>> + /* Host controller enable */
>> + if (ufshcd_hba_enable(hba)) {
>> dev_err(hba->dev,
>> "Reset: Controller initialization failed\n");
>> return FAILED;
>> }
>> +
>> + if (ufshcd_link_startup(hba)) {
>> + dev_err(hba->dev,
>> + "Reset: Link start-up failed\n");
>> + return FAILED;
>> + }
>> +
>> return SUCCESS;
>> }
>>
>> @@ -1434,6 +1524,17 @@ ufshcd_transfer_rsp_status(struct ufs_hba *hba,
>> struct ufshcd_lrb *lrbp)
>> }
>>
>> /**
>> + * ufshcd_uic_cmd_compl - handle completion of uic command
>> + * @hba: per adapter instance
>> + */
>> +static void ufshcd_uic_cmd_compl(struct ufs_hba *hba)
>> +{
>> + hba->active_uic_cmd->argument2 |=
>> + ufshcd_get_uic_cmd_result(hba);
>> + complete(&hba->active_uic_cmd->done);
>> +}
>> +
>> +/**
>> * ufshcd_transfer_req_compl - handle SCSI and query command
>> completion
>> * @hba: per adapter instance
>> */
>> @@ -1473,28 +1574,6 @@ static void ufshcd_transfer_req_compl(struct
>> ufs_hba *hba)
>> }
>>
>> /**
>> - * ufshcd_uic_cc_handler - handle UIC command completion
>> - * @work: pointer to a work queue structure
>> - *
>> - * Returns 0 on success, non-zero value on failure
>> - */
>> -static void ufshcd_uic_cc_handler (struct work_struct *work)
>> -{
>> - struct ufs_hba *hba;
>> -
>> - hba = container_of(work, struct ufs_hba, uic_workq);
>> -
>> - if ((hba->active_uic_cmd.command == UIC_CMD_DME_LINK_STARTUP) &&
>> - !(ufshcd_get_uic_cmd_result(hba))) {
>> -
>> - if (ufshcd_make_hba_operational(hba))
>> - dev_err(hba->dev,
>> - "cc: hba not operational state\n");
>> - return;
>> - }
>> -}
>> -
>> -/**
>> * ufshcd_fatal_err_handler - handle fatal errors
>> * @hba: per adapter instance
>> */
>> @@ -1555,7 +1634,7 @@ static void ufshcd_sl_intr(struct ufs_hba *hba,
>> u32 intr_status)
>> ufshcd_err_handler(hba);
>>
>> if (intr_status & UIC_COMMAND_COMPL)
>> - schedule_work(&hba->uic_workq);
>> + ufshcd_uic_cmd_compl(hba);
>>
>> if (intr_status & UTP_TASK_REQ_COMPL)
>> ufshcd_tmc_handler(hba);
>> @@ -1778,6 +1857,21 @@ out:
>> return err;
>> }
>>
>> +/**
>> + * ufshcd_async_scan - asynchronous execution for link startup
>> + * @data: data pointer to pass to this function
>> + * @cookie: cookie data
>> + */
>> +static void ufshcd_async_scan(void *data, async_cookie_t cookie)
>> +{
>> + struct ufs_hba *hba = (struct ufs_hba *)data;
>> + int ret;
>> +
>> + ret = ufshcd_link_startup(hba);
>> + if (!ret)
>> + scsi_scan_host(hba->host);
>> +}
>> +
>> static struct scsi_host_template ufshcd_driver_template = {
>> .module = THIS_MODULE,
>> .name = UFSHCD,
>> @@ -1939,12 +2033,14 @@ int ufshcd_init(struct device *dev, struct
>> ufs_hba **hba_handle,
>> init_waitqueue_head(&hba->ufshcd_tm_wait_queue);
>>
>> /* Initialize work queues */
>> - INIT_WORK(&hba->uic_workq, ufshcd_uic_cc_handler);
>> INIT_WORK(&hba->feh_workq, ufshcd_fatal_err_handler);
>>
>> /* Initialize mutex for query requests */
>> mutex_init(&hba->query.lock_ufs_query);
>>
>> + /* Initialize UIC command mutex */
>> + mutex_init(&hba->uic_cmd_mutex);
>> +
>> /* IRQ registration */
>> err = request_irq(irq, ufshcd_intr, IRQF_SHARED, UFSHCD, hba);
>> if (err) {
>> @@ -1965,14 +2061,17 @@ int ufshcd_init(struct device *dev, struct
>> ufs_hba **hba_handle,
>> goto out_free_irq;
>> }
>>
>> - /* Initialization routine */
>> - err = ufshcd_initialize_hba(hba);
>> + /* Host controller enable */
>> + err = ufshcd_hba_enable(hba);
>> if (err) {
>> - dev_err(hba->dev, "Initialization failed\n");
>> + dev_err(hba->dev, "Host controller enable failed\n");
>> goto out_remove_scsi_host;
>> }
>> +
>> *hba_handle = hba;
>>
>> + async_schedule(ufshcd_async_scan, hba);
>> +
>> return 0;
>>
>> out_remove_scsi_host:
>> diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
>> index d98e046..974bd07 100644
>> --- a/drivers/scsi/ufs/ufshcd.h
>> +++ b/drivers/scsi/ufs/ufshcd.h
>> @@ -51,6 +51,7 @@
>> #include <linux/bitops.h>
>> #include <linux/pm_runtime.h>
>> #include <linux/clk.h>
>> +#include <linux/completion.h>
>>
>> #include <asm/irq.h>
>> #include <asm/byteorder.h>
>> @@ -76,6 +77,7 @@
>> * @argument3: UIC command argument 3
>> * @cmd_active: Indicate if UIC command is outstanding
>> * @result: UIC command result
>> + * @done: UIC command completion
>> */
>> struct uic_command {
>> u32 command;
>> @@ -84,6 +86,7 @@ struct uic_command {
>> u32 argument3;
>> int cmd_active;
>> int result;
>> + struct completion done;
>> };
>>
>> /**
>> @@ -150,11 +153,11 @@ struct ufs_query {
>> * @ufs_version: UFS Version to which controller complies
>> * @irq: Irq number of the controller
>> * @active_uic_cmd: handle of active UIC command
>> + * @uic_cmd_mutex: mutex for uic command
>> * @ufshcd_tm_wait_queue: wait queue for task management
>> * @tm_condition: condition variable for task management
>> * @ufshcd_state: UFSHCD states
>> * @intr_mask: Interrupt Mask Bits
>> - * @uic_workq: Work queue for UIC completion handling
>> * @feh_workq: Work queue for fatal controller error handling
>> * @errors: HBA errors
>> * @query: query request information
>> @@ -186,7 +189,9 @@ struct ufs_hba {
>> u32 ufs_version;
>> unsigned int irq;
>>
>> - struct uic_command active_uic_cmd;
>> + struct uic_command *active_uic_cmd;
>> + struct mutex uic_cmd_mutex;
>> +
>> wait_queue_head_t ufshcd_tm_wait_queue;
>> unsigned long tm_condition;
>>
>> @@ -194,7 +199,6 @@ struct ufs_hba {
>> u32 intr_mask;
>>
>> /* Work Queues */
>> - struct work_struct uic_workq;
>> struct work_struct feh_workq;
>>
>> /* HBA Errors */
>>
>
> --
> Regards,
> Sujit
> --
> To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
Maya Erez
QUALCOMM ISRAEL, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
