> -----Original Message----- > From: Hannes Reinecke [mailto:hare@xxxxxxx] > Sent: Monday, April 08, 2013 10:42 AM > To: KY Srinivasan > Cc: James Bottomley; gregkh@xxxxxxxxxxxxxxxxxxx; linux- > kernel@xxxxxxxxxxxxxxx; devel@xxxxxxxxxxxxxxxxxxxxxx; ohering@xxxxxxxx; > hch@xxxxxxxxxxxxx; linux-scsi@xxxxxxxxxxxxxxx > Subject: Re: scanning for LUNs > > On 04/04/2013 07:12 PM, KY Srinivasan wrote: > > > > > >> -----Original Message----- > >> From: James Bottomley [mailto:jbottomley@xxxxxxxxxxxxx] > >> Sent: Thursday, April 04, 2013 11:15 AM > >> To: KY Srinivasan > >> Cc: gregkh@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; > >> devel@xxxxxxxxxxxxxxxxxxxxxx; ohering@xxxxxxxx; hch@xxxxxxxxxxxxx; linux- > >> scsi@xxxxxxxxxxxxxxx > >> Subject: Re: scanning for LUNs > >> > >> On Thu, 2013-04-04 at 08:12 -0700, K. Y. Srinivasan wrote: > >>> Here is the code snippet for scanning LUNS (drivers/scsi/scsi_scan.c in > function > >>> __scsi_scan_target()): > >>> > >>> /* > >>> * Scan LUN 0, if there is some response, scan further. Ideally, we > >>> * would not configure LUN 0 until all LUNs are scanned. > >>> */ > >>> res = scsi_probe_and_add_lun(starget, 0, &bflags, NULL, rescan, NULL); > >>> if (res == SCSI_SCAN_LUN_PRESENT || res == > >> SCSI_SCAN_TARGET_PRESENT) { > >>> if (scsi_report_lun_scan(starget, bflags, rescan) != 0) > >>> > >>> > >>> So, if we don't get a response while scanning LUN0, we will not use > >>> scsi_report_lun_scan(). > >>> On Hyper-V, the scsi emulation on the host does not treat LUN0 as > >>> anything special and we > >>> could have situations where the only device under a scsi controller is > >>> at a location other than 0 > >>> or 1. In this case the standard LUN scanning code in Linux fails to > >>> detect this device. Is this > >>> behaviour expected? Why is LUN0 treated differently here. Looking at > >>> the scsi spec, I am not sure > >>> if this is what is specified. Any help/guidance will be greatly > >>> appreciated. > >> > >> Why don't you describe the problem. We can't scan randomly a bunch of > >> LUNs hoping for a response (the space is 10^19). SAM thinks you use > >> LUNW for this, but that's not well supported. We can't annoy USB > >> devices by probing with REPORT LUNS, so conventionally most arrays > >> return something for LUN0 even if they don't actually have one (That's > >> what the peripheral qualifier codes are supposed to be about). We > >> translate PQ1 and PQ2 to SCSI_SCAN_TARGET_PRESENT, which means no > LUN, > >> but there is a target to scan here. > >> > >> If you're sending back an error to an INQUIRY to LUN0, then you're out > >> of spec. The SCSI standards say: > >> > >> SPC3 6.4.1: In response to an INQUIRY command received by an > >> incorrect logical unit, the SCSI target device shall return the > >> INQUIRY data with the peripheral qualifier set to the value > >> defined in 6.4.2. The INQUIRY command shall return CHECK > >> CONDITION status only when the device server is unable to return > >> the requested INQUIRY data > > > > Thanks James. I will further investigate the issue on our platform. > > > Or check if you can use W_LUN for scanning. > I've done a patchset for this (check the mailing list). > > Using W_LUN is precisely for this type of setup. > > (And would provide me with another scenario for using W_LUNs :-) Thanks Hannes. What is the status on this patch; is it planned for the next upstream release? Regards, K. Y > > Cheers, > > Hannes > -- > Dr. Hannes Reinecke zSeries & Storage > hare@xxxxxxx +49 911 74053 688 > SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg > GF: J. Hawn, J. Guild, F. Imendörffer, HRB 16746 (AG Nürnberg) > -- To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
