Re: Wrong DIF guard tag on ext2 write

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



James Bottomley, on 06/01/2010 05:27 PM wrote:
On Tue, 2010-06-01 at 12:30 +0200, Christof Schmitt wrote:
What is the best strategy to continue with the invalid guard tags on
write requests? Should this be fixed in the filesystems?

For write requests, as long as the page dirty bit is still set, it's
safe to drop the request, since it's already going to be repeated.  What
we probably want is an error code we can return that the layer that sees
both the request and the page flags can make the call.

Another idea would be to pass invalid guard tags on write requests
down to the hardware, expect an "invalid guard tag" error and report
it to the block layer where a new checksum is generated and the
request is issued again. Basically implement a retry through the whole
I/O stack. But this also sounds complicated.

No, no ... as long as the guard tag is wrong because the fs changed the
page, the write request for the updated page will already be queued or
in-flight, so there's no need to retry.

There's one interesting problem here, at least theoretically, with SCSI or similar transports which allow to have commands queue depth >1 and allowed to internally reorder queued requests. I don't know the FS/block layers sufficiently well to tell if sending several requests for the same page really possible or not, but we can see a real life problem, which can be well explained if it's possible.

The problem could be if the second (rewrite) request (SCSI command) for the same page queued to the corresponding device before the original request finished. Since the device allowed to freely reorder requests, there's a probability that the original write request would hit the permanent storage *AFTER* the retry request, hence the data changes it's carrying would be lost, hence welcome data corruption.

For single parallel SCSI or SAS devices such race may look practically impossible, but for sophisticated clusters when many nodes pretending to be a single SCSI device in a load balancing configuration, it becomes very real.

The real life problem we can see in an active-active DRBD-setup. In this configuration 2 nodes act as a single SCST-powered SCSI device and they both run DRBD to keep their backstorage in-sync. The initiator uses them as a single multipath device in an active-active round-robin load-balancing configuration, i.e. sends requests to both nodes in parallel, then DRBD takes care to replicate the requests to the other node.

The problem is that sometimes DRBD complies about concurrent local writes, like:

kernel: drbd0: scsi_tgt0[12503] Concurrent local write detected! [DISCARD L] new: 144072784s +8192; pending: 144072784s +8192

This message means that DRBD detected that both nodes received overlapping writes on the same block(s) and DRBD can't figure out which one to store. This is possible only if the initiator sent the second write request before the first one completed.

The topic of the discussion could well explain the cause of that. But, unfortunately, people who reported it forgot to note which OS they run on the initiator, i.e. I can't say for sure it's Linux.

Vlad

--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]
  Powered by Linux