Anil Veerabhadrappa wrote:
* When using iface, bnx2i was unable to offload further connections after
all active sessions are logged out. bnx2i will unregister the device from
cnic when the last connection is torn down. Next call to ep_connect()
will fail because the device is not registered. This issue is not seen
if shost == NULL is passed to ep_connect() call because in that case bnx2i
will registers all known devices with cnic before doing a route look-up.
When shost != NULL, bnx2i knows the device on which to offload the
connection and has to register this device before attempting to offload
the connection
Signed-off-by: Anil Veerabhadrappa <anilgv@xxxxxxxxxxxx>
Reviewed-by: Michael Chan <mchan@xxxxxxxxxxxx>
---
drivers/scsi/bnx2i/bnx2i_init.c | 7 +++++--
drivers/scsi/bnx2i/bnx2i_iscsi.c | 7 +++++--
2 files changed, 10 insertions(+), 4 deletions(-)
diff --git a/drivers/scsi/bnx2i/bnx2i_init.c b/drivers/scsi/bnx2i/bnx2i_init.c
index fd78540..0c4210d 100644
--- a/drivers/scsi/bnx2i/bnx2i_init.c
+++ b/drivers/scsi/bnx2i/bnx2i_init.c
@@ -185,14 +185,17 @@ void bnx2i_stop(void *handle)
*/
void bnx2i_register_device(struct bnx2i_hba *hba)
{
+ int rc;
+
if (test_bit(ADAPTER_STATE_GOING_DOWN, &hba->adapter_state) ||
test_bit(BNX2I_CNIC_REGISTERED, &hba->reg_with_cnic)) {
return;
}
- hba->cnic->register_device(hba->cnic, CNIC_ULP_ISCSI, hba);
+ rc = hba->cnic->register_device(hba->cnic, CNIC_ULP_ISCSI, hba);
- set_bit(BNX2I_CNIC_REGISTERED, &hba->reg_with_cnic);
+ if (!rc)
+ set_bit(BNX2I_CNIC_REGISTERED, &hba->reg_with_cnic);
}
diff --git a/drivers/scsi/bnx2i/bnx2i_iscsi.c b/drivers/scsi/bnx2i/bnx2i_iscsi.c
index f741219..98148f3 100644
--- a/drivers/scsi/bnx2i/bnx2i_iscsi.c
+++ b/drivers/scsi/bnx2i/bnx2i_iscsi.c
@@ -1653,15 +1653,18 @@ static struct iscsi_endpoint *bnx2i_ep_connect(struct Scsi_Host *shost,
struct iscsi_endpoint *ep;
int rc = 0;
- if (shost)
+ if (shost) {
/* driver is given scsi host to work with */
hba = iscsi_host_priv(shost);
- else
+ /* Register the device with cnic if not already done so */
+ bnx2i_register_device(hba);
+ } else
/*
* check if the given destination can be reached through
* a iscsi capable NetXtreme2 device
*/
hba = bnx2i_check_route(dst_addr);
+
if (!hba) {
rc = -ENOMEM;
goto check_busy;
Do you want to do the test_bit(BNX2I_CNIC_REGISTERED,
&hba->reg_with_cnic) test here instead of down below. If it failed then
you might try to do a cm_create on a cnic that is not properly registered.
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
