[PATCH 3/4] dpt_i2o: 64 bit support
This is the code to actually support 64 bit platforms. 64 bit
DMA is enabled on both x86_32 PAE and 64 bit platforms.
This code is based in part on the unofficial adaptec 64-bit
dpt_i2o driver update that I got from Mark Salyzyn at Adaptec.
Signed-off-by: Miquel van Smoorenburg <miquels@xxxxxxxxxx>
diff -ruN linux-2.6.25/drivers/scsi/Kconfig ../linux-2.6.25-dpt64-02/drivers/scsi/Kconfig
--- linux-2.6.25/drivers/scsi/Kconfig 2008-05-01 17:00:19.000000000 +0200
+++ ../linux-2.6.25-dpt64-02/drivers/scsi/Kconfig 2008-04-18 23:09:44.000000000 +0200
@@ -504,10 +504,9 @@
source "drivers/scsi/aic7xxx/Kconfig.aic79xx"
source "drivers/scsi/aic94xx/Kconfig"
-# All the I2O code and drivers do not seem to be 64bit safe.
config SCSI_DPT_I2O
tristate "Adaptec I2O RAID support "
- depends on !64BIT && SCSI && PCI && VIRT_TO_BUS
+ depends on SCSI && PCI && VIRT_TO_BUS
help
This driver supports all of Adaptec's I2O based RAID controllers as
well as the DPT SmartRaid V cards. This is an Adaptec maintained
diff -ruN linux-2.6.25/drivers/scsi/dpt/dpti_ioctl.h ../linux-2.6.25-dpt64-02/drivers/scsi/dpt/dpti_ioctl.h
--- linux-2.6.25/drivers/scsi/dpt/dpti_ioctl.h 2008-04-17 04:49:44.000000000 +0200
+++ ../linux-2.6.25-dpt64-02/drivers/scsi/dpt/dpti_ioctl.h 2008-05-01 15:59:40.000000000 +0200
@@ -89,7 +89,7 @@
int njobs; /* # of jobs sent to HA */
int qdepth; /* Controller queue depth. */
int wakebase; /* mpx wakeup base index. */
- uLONG SGsize; /* Scatter/Gather list size. */
+ uINT SGsize; /* Scatter/Gather list size. */
unsigned heads; /* heads for drives on cntlr. */
unsigned sectors; /* sectors for drives on cntlr. */
uCHAR do_drive32; /* Flag for Above 16 MB Ability */
@@ -97,8 +97,8 @@
char idPAL[4]; /* 4 Bytes Of The ID Pal */
uCHAR primary; /* 1 For Primary, 0 For Secondary */
uCHAR eataVersion; /* EATA Version */
- uLONG cpLength; /* EATA Command Packet Length */
- uLONG spLength; /* EATA Status Packet Length */
+ uINT cpLength; /* EATA Command Packet Length */
+ uINT spLength; /* EATA Status Packet Length */
uCHAR drqNum; /* DRQ Index (0,5,6,7) */
uCHAR flag1; /* EATA Flags 1 (Byte 9) */
uCHAR flag2; /* EATA Flags 2 (Byte 30) */
@@ -107,23 +107,23 @@
typedef struct {
uSHORT length; // Remaining length of this
uSHORT drvrHBAnum; // Relative HBA # used by the driver
- uLONG baseAddr; // Base I/O address
+ uINT baseAddr; // Base I/O address
uSHORT blinkState; // Blink LED state (0=Not in blink LED)
uCHAR pciBusNum; // PCI Bus # (Optional)
uCHAR pciDeviceNum; // PCI Device # (Optional)
uSHORT hbaFlags; // Miscellaneous HBA flags
uSHORT Interrupt; // Interrupt set for this device.
# if (defined(_DPT_ARC))
- uLONG baseLength;
+ uINT baseLength;
ADAPTER_OBJECT *AdapterObject;
LARGE_INTEGER DmaLogicalAddress;
PVOID DmaVirtualAddress;
LARGE_INTEGER ReplyLogicalAddress;
PVOID ReplyVirtualAddress;
# else
- uLONG reserved1; // Reserved for future expansion
- uLONG reserved2; // Reserved for future expansion
- uLONG reserved3; // Reserved for future expansion
+ uINT reserved1; // Reserved for future expansion
+ uINT reserved2; // Reserved for future expansion
+ uINT reserved3; // Reserved for future expansion
# endif
} drvrHBAinfo_S;
diff -ruN linux-2.6.25/drivers/scsi/dpt/dptsig.h ../linux-2.6.25-dpt64-02/drivers/scsi/dpt/dptsig.h
--- linux-2.6.25/drivers/scsi/dpt/dptsig.h 2008-04-17 04:49:44.000000000 +0200
+++ ../linux-2.6.25-dpt64-02/drivers/scsi/dpt/dptsig.h 2008-05-01 14:39:25.000000000 +0200
@@ -33,11 +33,7 @@
/* to make sure we are talking the same size under all OS's */
typedef unsigned char sigBYTE;
typedef unsigned short sigWORD;
-#if (defined(_MULTI_DATAMODEL) && defined(sun) && !defined(_ILP32))
-typedef uint32_t sigLONG;
-#else
-typedef unsigned long sigLONG;
-#endif
+typedef unsigned int sigINT;
/*
* use sigWORDLittleEndian for:
@@ -300,7 +296,7 @@
sigBYTE dsFiletype; /* type of file */
sigBYTE dsFiletypeFlags; /* flags to specify load type, etc. */
sigBYTE dsOEM; /* OEM file was created for */
- sigLONG dsOS; /* which Operating systems */
+ sigINT dsOS; /* which Operating systems */
sigWORD dsCapabilities; /* RAID levels, etc. */
sigWORD dsDeviceSupp; /* Types of SCSI devices supported */
sigWORD dsAdapterSupp; /* DPT adapter families supported */
diff -ruN linux-2.6.25/drivers/scsi/dpt/sys_info.h ../linux-2.6.25-dpt64-02/drivers/scsi/dpt/sys_info.h
--- linux-2.6.25/drivers/scsi/dpt/sys_info.h 2008-04-17 04:49:44.000000000 +0200
+++ ../linux-2.6.25-dpt64-02/drivers/scsi/dpt/sys_info.h 2008-05-01 15:16:26.000000000 +0200
@@ -145,8 +145,8 @@
uCHAR smartROMRevision;
uSHORT flags; /* See bit definitions above */
uSHORT conventionalMemSize; /* in KB */
- uLONG extendedMemSize; /* in KB */
- uLONG osType; /* Same as DPTSIG's definition */
+ uINT extendedMemSize; /* in KB */
+ uINT osType; /* Same as DPTSIG's definition */
uCHAR osMajorVersion;
uCHAR osMinorVersion; /* The OS version */
uCHAR osRevision;
diff -ruN linux-2.6.25/drivers/scsi/dpt_i2o.c ../linux-2.6.25-dpt64-02/drivers/scsi/dpt_i2o.c
--- linux-2.6.25/drivers/scsi/dpt_i2o.c 2008-05-01 23:34:03.000000000 +0200
+++ ../linux-2.6.25-dpt64-02/drivers/scsi/dpt_i2o.c 2008-05-01 16:38:58.000000000 +0200
@@ -111,10 +116,17 @@
static adpt_hba* hba_chain = NULL;
static int hba_count = 0;
+#ifdef CONFIG_COMPAT
+static long compat_adpt_ioctl(struct file *, unsigned int, unsigned long);
+#endif
+
static const struct file_operations adpt_fops = {
.ioctl = adpt_ioctl,
.open = adpt_open,
- .release = adpt_close
+ .release = adpt_close,
+#ifdef CONFIG_COMPAT
+ .compat_ioctl = compat_adpt_ioctl,
+#endif
};
/* Structures and definitions for synchronous message posting.
@@ -138,6 +150,11 @@
*============================================================================
*/
+static inline int dpt_dma64(adpt_hba *pHba)
+{
+ return (sizeof(dma_addr_t) > 4 && (pHba)->dma64);
+}
+
static inline u32 dma_high(dma_addr_t addr)
{
return upper_32_bits(addr);
@@ -277,7 +294,7 @@
static void adpt_inquiry(adpt_hba* pHba)
{
- u32 msg[14];
+ u32 msg[17];
u32 *mptr;
u32 *lenptr;
int direction;
@@ -301,7 +318,10 @@
direction = 0x00000000;
scsidir =0x40000000; // DATA IN (iop<--dev)
- reqlen = 14; // SINGLE SGE
+ if (dpt_dma64(pHba))
+ reqlen = 17; // SINGLE SGE, 64 bit
+ else
+ reqlen = 14; // SINGLE SGE, 32 bit
/* Stick the headers on */
msg[0] = reqlen<<16 | SGL_OFFSET_12;
msg[1] = (0xff<<24|HOST_TID<<12|ADAPTER_TID);
@@ -334,8 +354,16 @@
/* Now fill in the SGList and command */
*lenptr = len;
- *mptr++ = 0xD0000000|direction|len;
- *mptr++ = addr;
+ if (dpt_dma64(pHba)) {
+ *mptr++ = (0x7C<<24)+(2<<16)+0x02; /* Enable 64 bit */
+ *mptr++ = 1 << PAGE_SHIFT;
+ *mptr++ = 0xD0000000|direction|len;
+ *mptr++ = dma_low(addr);
+ *mptr++ = dma_high(addr);
+ } else {
+ *mptr++ = 0xD0000000|direction|len;
+ *mptr++ = addr;
+ }
// Send it on it's way
rcode = adpt_i2o_post_wait(pHba, msg, reqlen<<2, 120);
@@ -628,6 +656,92 @@
return len;
}
+/*
+ * Turn a struct scsi_cmnd * into a unique 32 bit 'context'.
+ */
+static u32 adpt_cmd_to_context(struct scsi_cmnd *cmd)
+{
+ return (u32)cmd->serial_number;
+}
+
+/*
+ * Go from a u32 'context' to a struct scsi_cmnd * .
+ * This could probably be made more efficient.
+ */
+static struct scsi_cmnd *
+ adpt_cmd_from_context(adpt_hba * pHba, u32 context)
+{
+ struct scsi_cmnd * cmd;
+ struct scsi_device * d;
+
+ if (context == 0)
+ return NULL;
+
+ spin_unlock(pHba->host->host_lock);
+ shost_for_each_device(d, pHba->host) {
+ unsigned long flags;
+ spin_lock_irqsave(&d->list_lock, flags);
+ list_for_each_entry(cmd, &d->cmd_list, list) {
+ if (((u32)cmd->serial_number == context)) {
+ spin_unlock_irqrestore(&d->list_lock, flags);
+ scsi_device_put(d);
+ spin_lock(pHba->host->host_lock);
+ return cmd;
+ }
+ }
+ spin_unlock_irqrestore(&d->list_lock, flags);
+ }
+ spin_lock(pHba->host->host_lock);
+
+ return NULL;
+}
+
+/*
+ * Turn a pointer to ioctl reply data into an u32 'context'
+ */
+static u32 adpt_ioctl_to_context(adpt_hba * pHba, void *reply)
+{
+#if BITS_PER_LONG == 32
+ return (u32)(unsigned long)reply;
+#else
+ ulong flags = 0;
+ u32 nr, i;
+
+ spin_lock_irqsave(pHba->host->host_lock, flags);
+ nr = ARRAY_SIZE(pHba->ioctl_reply_context);
+ for (i = 0; i < nr; i++) {
+ if (pHba->ioctl_reply_context[i] == NULL) {
+ pHba->ioctl_reply_context[i] = reply;
+ break;
+ }
+ }
+ spin_unlock_irqrestore(pHba->host->host_lock, flags);
+ if (i >= nr) {
+ kfree (reply);
+ printk(KERN_WARNING"%s: Too many outstanding "
+ "ioctl commands\n", pHba->name);
+ return (u32)-1;
+ }
+
+ return i;
+#endif
+}
+
+/*
+ * Go from an u32 'context' to a pointer to ioctl reply data.
+ */
+static void *adpt_ioctl_from_context(adpt_hba *pHba, u32 context)
+{
+#if BITS_PER_LONG == 32
+ return (void *)(unsigned long)context;
+#else
+ void *p = pHba->ioctl_reply_context[context];
+ pHba->ioctl_reply_context[context] = NULL;
+
+ return p;
+#endif
+}
+
/*===========================================================================
* Error Handling routines
*===========================================================================
@@ -655,7 +769,7 @@
msg[1] = I2O_CMD_SCSI_ABORT<<24|HOST_TID<<12|dptdevice->tid;
msg[2] = 0;
msg[3]= 0;
- msg[4] = (u32)cmd;
+ msg[4] = adpt_cmd_to_context(cmd);
if (pHba->host)
spin_lock_irq(pHba->host->host_lock);
rcode = adpt_i2o_post_wait(pHba, msg, sizeof(msg), FOREVER);
@@ -867,6 +981,7 @@
u32 hba_map1_area_size = 0;
void __iomem *base_addr_virt = NULL;
void __iomem *msg_addr_virt = NULL;
+ int dma64 = 0;
int raptorFlag = FALSE;
@@ -880,7 +995,16 @@
}
pci_set_master(pDev);
- if (pci_set_dma_mask(pDev, DMA_32BIT_MASK))
+
+ /*
+ * See if we should enable dma64 mode.
+ */
+ if (sizeof(dma_addr_t) > 4 &&
+ pci_set_dma_mask(pDev, DMA_64BIT_MASK) == 0) {
+ if (dma_get_required_mask(&pDev->dev) > DMA_32BIT_MASK)
+ dma64 = 1;
+ }
+ if (!dma64 && pci_set_dma_mask(pDev, DMA_32BIT_MASK) != 0)
return -EINVAL;
/* adapter only supports message blocks below 4GB */
@@ -906,6 +1030,25 @@
raptorFlag = TRUE;
}
+#if BITS_PER_LONG == 64
+ /*
+ * The original Adaptec 64 bit driver has this comment here:
+ * "x86_64 machines need more optimal mappings"
+ *
+ * I assume some HBAs report ridiculously large mappings
+ * and we need to limit them on platforms with IOMMUs.
+ */
+ if (raptorFlag == TRUE) {
+ if (hba_map0_area_size > 128)
+ hba_map0_area_size = 128;
+ if (hba_map1_area_size > 524288)
+ hba_map1_area_size = 524288;
+ } else {
+ if (hba_map0_area_size > 524288)
+ hba_map0_area_size = 524288;
+ }
+#endif
+
base_addr_virt = ioremap(base_addr0_phys,hba_map0_area_size);
if (!base_addr_virt) {
pci_release_regions(pDev);
@@ -968,16 +1111,22 @@
pHba->state = DPTI_STATE_RESET;
pHba->pDev = pDev;
pHba->devices = NULL;
+ pHba->dma64 = dma64;
// Initializing the spinlocks
spin_lock_init(&pHba->state_lock);
spin_lock_init(&adpt_post_wait_lock);
if(raptorFlag == 0){
- printk(KERN_INFO"Adaptec I2O RAID controller %d at %p size=%x irq=%d\n",
- hba_count-1, base_addr_virt, hba_map0_area_size, pDev->irq);
+ printk(KERN_INFO "Adaptec I2O RAID controller"
+ " %d at %p size=%x irq=%d%s\n",
+ hba_count-1, base_addr_virt,
+ hba_map0_area_size, pDev->irq,
+ dma64 ? " (64-bit DMA)" : "");
} else {
- printk(KERN_INFO"Adaptec I2O RAID controller %d irq=%d\n",hba_count-1, pDev->irq);
+ printk(KERN_INFO"Adaptec I2O RAID controller %d irq=%d%s\n",
+ hba_count-1, pDev->irq,
+ dma64 ? " (64-bit DMA)" : "");
printk(KERN_INFO" BAR0 %p - size= %x\n",base_addr_virt,hba_map0_area_size);
printk(KERN_INFO" BAR1 %p - size= %x\n",msg_addr_virt,hba_map1_area_size);
}
@@ -1030,6 +1179,8 @@
if(pHba->msg_addr_virt != pHba->base_addr_virt){
iounmap(pHba->msg_addr_virt);
}
+ if(pHba->FwDebugBuffer_P)
+ iounmap(pHba->FwDebugBuffer_P);
if(pHba->hrt) {
dma_free_coherent(&pHba->pDev->dev,
pHba->hrt->num_entries * pHba->hrt->entry_len << 2,
@@ -1657,10 +1808,13 @@
}
sg_offset = (msg[0]>>4)&0xf;
msg[2] = 0x40000000; // IOCTL context
- msg[3] = (u32)reply;
+ msg[3] = adpt_ioctl_to_context(pHba, reply);
+ if (msg[3] == (u32)-1)
+ return -EBUSY;
+
memset(sg_list,0, sizeof(sg_list[0])*pHba->sg_tablesize);
if(sg_offset) {
- // TODO 64bit fix
+ // TODO add 64 bit API
struct sg_simple_element *sg = (struct sg_simple_element*) (msg+sg_offset);
sg_count = (size - sg_offset*4) / sizeof(struct sg_simple_element);
if (sg_count > pHba->sg_tablesize){
@@ -1689,15 +1843,15 @@
sg_list[sg_index++] = p; // sglist indexed with input frame, not our internal frame.
/* Copy in the user's SG buffer if necessary */
if(sg[i].flag_count & 0x04000000 /*I2O_SGL_FLAGS_DIR*/) {
- // TODO 64bit fix
- if (copy_from_user(p,(void __user *)sg[i].addr_bus, sg_size)) {
+ // sg_simple_element API is 32 bit
+ if (copy_from_user(p,(void __user *)(ulong)sg[i].addr_bus, sg_size)) {
printk(KERN_DEBUG"%s: Could not copy SG buf %d FROM user\n",pHba->name,i);
rcode = -EFAULT;
goto cleanup;
}
}
- //TODO 64bit fix
- sg[i].addr_bus = (u32)virt_to_bus(p);
+ /* sg_simple_element API is 32 bit, but addr < 4GB */
+ sg[i].addr_bus = addr;
}
}
@@ -1725,7 +1879,7 @@
if(sg_offset) {
/* Copy back the Scatter Gather buffers back to user space */
u32 j;
- // TODO 64bit fix
+ // TODO add 64 bit API
struct sg_simple_element* sg;
int sg_size;
@@ -1745,14 +1899,14 @@
}
sg_count = (size - sg_offset*4) / sizeof(struct sg_simple_element);
- // TODO 64bit fix
+ // TODO add 64 bit API
sg = (struct sg_simple_element*)(msg + sg_offset);
for (j = 0; j < sg_count; j++) {
/* Copy out the SG list to user's buffer if necessary */
if(! (sg[j].flag_count & 0x4000000 /*I2O_SGL_FLAGS_DIR*/)) {
sg_size = sg[j].flag_count & 0xffffff;
- // TODO 64bit fix
- if (copy_to_user((void __user *)sg[j].addr_bus,sg_list[j], sg_size)) {
+ // sg_simple_element API is 32 bit
+ if (copy_to_user((void __user *)(ulong)sg[j].addr_bus,sg_list[j], sg_size)) {
printk(KERN_WARNING"%s: Could not copy %p TO user %x\n",pHba->name, sg_list[j], sg[j].addr_bus);
rcode = -EFAULT;
goto cleanup;
@@ -1972,6 +2126,38 @@
return error;
}
+#ifdef CONFIG_COMPAT
+static long compat_adpt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
+{
+ struct inode *inode;
+ long ret;
+
+ inode = file->f_dentry->d_inode;
+
+ lock_kernel();
+
+ switch(cmd) {
+ case DPT_SIGNATURE:
+ case I2OUSRCMD:
+ case DPT_CTRLINFO:
+ case DPT_SYSINFO:
+ case DPT_BLINKLED:
+ case I2ORESETCMD:
+ case I2ORESCANCMD:
+ case (DPT_TARGET_BUSY & 0xFFFF):
+ case DPT_TARGET_BUSY:
+ ret = adpt_ioctl(inode, file, cmd, arg);
+ break;
+ default:
+ ret = -ENOIOCTLCMD;
+ }
+
+ unlock_kernel();
+
+ return ret;
+}
+#endif
static irqreturn_t adpt_isr(int irq, void *dev_id)
{
@@ -2032,7 +2218,7 @@
}
context = readl(reply+8);
if(context & 0x40000000){ // IOCTL
- void *p = (void *)readl(reply+12);
+ void *p = adpt_ioctl_from_context(pHba, readl(reply+12));
if( p != NULL) {
memcpy_fromio(p, reply, REPLY_FRAME_SIZE * 4);
}
@@ -2046,14 +2232,15 @@
status = I2O_POST_WAIT_OK;
}
if(!(context & 0x40000000)) {
- cmd = (struct scsi_cmnd*) readl(reply+12);
+ cmd = adpt_cmd_from_context(pHba,
+ readl(reply+12));
if(cmd != NULL) {
printk(KERN_WARNING"%s: Apparent SCSI cmd in Post Wait Context - cmd=%p context=%x\n", pHba->name, cmd, context);
}
}
adpt_i2o_post_wait_complete(context, status);
} else { // SCSI message
- cmd = (struct scsi_cmnd*) readl(reply+12);
+ cmd = adpt_cmd_from_context (pHba, readl(reply+12));
if(cmd != NULL){
scsi_dma_unmap(cmd);
if(cmd->serial_number != 0) { // If not timedout
@@ -2076,6 +2263,7 @@
int i;
u32 msg[MAX_MESSAGE_SIZE];
u32* mptr;
+ u32* lptr;
u32 *lenptr;
int direction;
int scsidir;
@@ -2083,6 +2271,7 @@
u32 len;
u32 reqlen;
s32 rcode;
+ dma_addr_t addr;
memset(msg, 0 , sizeof(msg));
len = scsi_bufflen(cmd);
@@ -2122,7 +2311,7 @@
// I2O_CMD_SCSI_EXEC
msg[1] = ((0xff<<24)|(HOST_TID<<12)|d->tid);
msg[2] = 0;
- msg[3] = (u32)cmd; /* We want the SCSI control block back */
+ msg[3] = adpt_cmd_to_context(cmd); /* Want SCSI control block back */
// Our cards use the transaction context as the tag for queueing
// Adaptec/DPT Private stuff
msg[4] = I2O_CMD_SCSI_EXEC|(DPT_ORGANIZATION_ID<<16);
@@ -2140,7 +2329,13 @@
memcpy(mptr, cmd->cmnd, cmd->cmd_len);
mptr+=4;
lenptr=mptr++; /* Remember me - fill in when we know */
- reqlen = 14; // SINGLE SGE
+ if (dpt_dma64(pHba)) {
+ reqlen = 16; // SINGLE SGE
+ *mptr++ = (0x7C<<24)+(2<<16)+0x02; /* Enable 64 bit */
+ *mptr++ = 1 << PAGE_SHIFT;
+ } else {
+ reqlen = 14; // SINGLE SGE
+ }
/* Now fill in the SGList and command */
nseg = scsi_dma_map(cmd);
@@ -2150,12 +2345,16 @@
len = 0;
scsi_for_each_sg(cmd, sg, nseg, i) {
+ lptr = mptr;
*mptr++ = direction|0x10000000|sg_dma_len(sg);
len+=sg_dma_len(sg);
- *mptr++ = sg_dma_address(sg);
+ addr = sg_dma_address(sg);
+ *mptr++ = dma_low(addr);
+ if (dpt_dma64(pHba))
+ *mptr++ = dma_high(addr);
/* Make this an end of list */
if (i == nseg - 1)
- mptr[-2] = direction|0xD0000000|sg_dma_len(sg);
+ *lptr = direction|0xD0000000|sg_dma_len(sg);
}
reqlen = mptr - msg;
*lenptr = len;
@@ -2824,7 +3023,17 @@
}
// Calculate the Scatter Gather list size
- pHba->sg_tablesize = (pHba->status_block->inbound_frame_size * 4 -40)/ sizeof(struct sg_simple_element);
+ if (dpt_dma64(pHba)) {
+ pHba->sg_tablesize
+ = ((pHba->status_block->inbound_frame_size * 4
+ - 14 * sizeof(u32))
+ / (sizeof(struct sg_simple_element) + sizeof(u32)));
+ } else {
+ pHba->sg_tablesize
+ = ((pHba->status_block->inbound_frame_size * 4
+ - 12 * sizeof(u32))
+ / sizeof(struct sg_simple_element));
+ }
if (pHba->sg_tablesize > SG_LIST_ELEMENTS) {
pHba->sg_tablesize = SG_LIST_ELEMENTS;
}
@@ -2916,13 +3125,19 @@
// I2O_DPT_EXEC_IOP_BUFFERS_GROUP_NO;
if(adpt_i2o_query_scalar(pHba, 0 , 0x8000, -1, buf, sizeof(buf))>=0) {
pHba->FwDebugBufferSize = buf[1];
- pHba->FwDebugBuffer_P = pHba->base_addr_virt + buf[0];
- pHba->FwDebugFlags_P = pHba->FwDebugBuffer_P + FW_DEBUG_FLAGS_OFFSET;
- pHba->FwDebugBLEDvalue_P = pHba->FwDebugBuffer_P + FW_DEBUG_BLED_OFFSET;
- pHba->FwDebugBLEDflag_P = pHba->FwDebugBLEDvalue_P + 1;
- pHba->FwDebugStrLength_P = pHba->FwDebugBuffer_P + FW_DEBUG_STR_LENGTH_OFFSET;
- pHba->FwDebugBuffer_P += buf[2];
- pHba->FwDebugFlags = 0;
+ pHba->FwDebugBuffer_P = ioremap(pHba->base_addr_phys + buf[0],
+ pHba->FwDebugBufferSize);
+ if (pHba->FwDebugBuffer_P) {
+ pHba->FwDebugFlags_P = pHba->FwDebugBuffer_P +
+ FW_DEBUG_FLAGS_OFFSET;
+ pHba->FwDebugBLEDvalue_P = pHba->FwDebugBuffer_P +
+ FW_DEBUG_BLED_OFFSET;
+ pHba->FwDebugBLEDflag_P = pHba->FwDebugBLEDvalue_P + 1;
+ pHba->FwDebugStrLength_P = pHba->FwDebugBuffer_P +
+ FW_DEBUG_STR_LENGTH_OFFSET;
+ pHba->FwDebugBuffer_P += buf[2];
+ pHba->FwDebugFlags = 0;
+ }
}
return 0;
diff -ruN linux-2.6.25/drivers/scsi/dpti.h ../linux-2.6.25-dpt64-02/drivers/scsi/dpti.h
--- linux-2.6.25/drivers/scsi/dpti.h 2008-05-01 23:34:03.000000000 +0200
+++ ../linux-2.6.25-dpt64-02/drivers/scsi/dpti.h 2008-04-24 22:36:29.000000000 +0200
@@ -233,6 +233,7 @@
u8 top_scsi_channel;
u8 top_scsi_id;
u8 top_scsi_lun;
+ u8 dma64;
i2o_status_block* status_block;
dma_addr_t status_block_pa;
@@ -252,6 +253,7 @@
void __iomem *FwDebugBLEDflag_P;// Virtual Addr Of FW Debug BLED
void __iomem *FwDebugBLEDvalue_P;// Virtual Addr Of FW Debug BLED
u32 FwDebugFlags;
+ u32 *ioctl_reply_context[4];
} adpt_hba;
struct sg_simple_element {
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
