hi, can anyone point me out, why the adaptec aic-9410W sas controller detects my sata drive but the kernel does not? you will find the relevant dmesg parts attached. cheers, raoul -- ____________________________________________________________________ DI (FH) Raoul Bhatia M.Sc. email. r.bhatia@xxxxxxx Technischer Leiter IPAX - Aloy Bhatia Hava OEG web. http://www.ipax.at Barawitzkagasse 10/2/2/11 email. office@xxxxxxx 1190 Wien tel. +43 1 3670030 FN 277995t HG Wien fax. +43 1 3670030 15 ____________________________________________________________________
sata_svw 0000:01:0e.0: version 2.3 ACPI: PCI Interrupt 0000:01:0e.0[A] -> GSI 11 (level, low) -> IRQ 11 scsi0 : sata_svw scsi1 : sata_svw scsi2 : sata_svw scsi3 : sata_svw ata1: SATA max UDMA/133 mmio m8192@0xff2fe000 port 0xff2fe000 irq 11 ata2: SATA max UDMA/133 mmio m8192@0xff2fe000 port 0xff2fe100 irq 11 ata3: SATA max UDMA/133 mmio m8192@0xff2fe000 port 0xff2fe200 irq 11 ata4: SATA max UDMA/133 mmio m8192@0xff2fe000 port 0xff2fe300 irq 11 ata1: SATA link down (SStatus 4 SControl 300) ata2: SATA link down (SStatus 4 SControl 300) ata3: SATA link down (SStatus 4 SControl 300) ata4: SATA link down (SStatus 4 SControl 300) aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded ACPI: PCI Interrupt 0000:03:07.0[A] -> GSI 25 (level, low) -> IRQ 25 aic94xx: found Adaptec AIC-9410W SAS/SATA Host Adapter, device 0000:03:07.0 scsi4 : aic94xx aic94xx: BIOS present (1,1), 1820 aic94xx: ue num:2, ue size:88 aic94xx: manuf sect SAS_ADDR 500e08100001b6b8 aic94xx: manuf sect PCBA SN aic94xx: ms: no phy parameters found aic94xx: ms: Creating default phy parameters aic94xx: ms: num_phy_desc: 8 aic94xx: ms: phy0: ENABLED aic94xx: ms: phy1: ENABLED aic94xx: ms: phy2: ENABLED aic94xx: ms: phy3: ENABLED aic94xx: ms: phy4: ENABLED aic94xx: ms: phy5: ENABLED aic94xx: ms: phy6: ENABLED aic94xx: ms: phy7: ENABLED aic94xx: ms: max_phys:0x8, num_phys:0x8 aic94xx: ms: enabled_phys:0xff aic94xx: ms: no connector map found aic94xx: ctrla: phy0: sas_addr: 500e08100001b6b8, sas rate:0x9-0x8, sata rate:0x0-0x0, flags:0x0 aic94xx: ctrla: phy1: sas_addr: 500e08100001b6b8, sas rate:0x9-0x8, sata rate:0x0-0x0, flags:0x0 aic94xx: ctrla: phy2: sas_addr: 500e08100001b6b8, sas rate:0x9-0x8, sata rate:0x0-0x0, flags:0x0 aic94xx: ctrla: phy3: sas_addr: 500e08100001b6b8, sas rate:0x9-0x8, sata rate:0x0-0x0, flags:0x0 aic94xx: ctrla: phy4: sas_addr: 500e08100001b6b8, sas rate:0x9-0x8, sata rate:0x0-0x0, flags:0x0 aic94xx: ctrla: phy5: sas_addr: 500e08100001b6b8, sas rate:0x9-0x8, sata rate:0x0-0x0, flags:0x0 aic94xx: ctrla: phy6: sas_addr: 500e08100001b6b8, sas rate:0x9-0x8, sata rate:0x0-0x0, flags:0x0 aic94xx: ctrla: phy7: sas_addr: 500e08100001b6b8, sas rate:0x9-0x8, sata rate:0x0-0x0, flags:0x0 aic94xx: max_scbs:512, max_ddbs:128 aic94xx: setting phy0 addr to 500e08100001b6b8 aic94xx: setting phy1 addr to 500e08100001b6b8 aic94xx: setting phy2 addr to 500e08100001b6b8 aic94xx: setting phy3 addr to 500e08100001b6b8 aic94xx: setting phy4 addr to 500e08100001b6b8 aic94xx: setting phy5 addr to 500e08100001b6b8 aic94xx: setting phy6 addr to 500e08100001b6b8 aic94xx: setting phy7 addr to 500e08100001b6b8 aic94xx: num_edbs:21 aic94xx: num_escbs:3 aic94xx: Found sequencer Firmware version 1.1 (V32A4) aic94xx: downloading CSEQ... aic94xx: dma-ing 8192 bytes aic94xx: verified 8192 bytes, passed aic94xx: downloading LSEQs... aic94xx: dma-ing 14336 bytes aic94xx: LSEQ0 verified 14336 bytes, passed aic94xx: LSEQ1 verified 14336 bytes, passed aic94xx: LSEQ2 verified 14336 bytes, passed aic94xx: LSEQ3 verified 14336 bytes, passed aic94xx: LSEQ4 verified 14336 bytes, passed aic94xx: LSEQ5 verified 14336 bytes, passed aic94xx: LSEQ6 verified 14336 bytes, passed aic94xx: LSEQ7 verified 14336 bytes, passed aic94xx: max_scbs:446 aic94xx: first_scb_site_no:0x20 aic94xx: last_scb_site_no:0x1fe aic94xx: First SCB dma_handle: 0x13dca8000 aic94xx: device 0000:03:07.0: SAS addr 500e08100001b6b8, PCBA SN , 8 phys, 8 enabled phys, flash present, BIOS build 1820 aic94xx: posting 3 escbs aic94xx: escbs posted aic94xx: posting 8 control phy scbs aic94xx: control_phy_tasklet_complete: phy5, lrate:0x8, proto:0xe aic94xx: control_phy_tasklet_complete: phy4, lrate:0x9, proto:0xe aic94xx: escb_tasklet_complete: phy4: BYTES_DMAED aic94xx: SAS proto IDENTIFY: aic94xx: 00: 10 00 00 08 aic94xx: 04: 00 00 00 00 aic94xx: 08: 00 00 00 00 aic94xx: 0c: 50 00 c5 00 aic94xx: 10: 07 92 fb dd aic94xx: 14: 00 00 00 00 aic94xx: 18: 00 00 00 00 aic94xx: asd_form_port: updating phy_mask 0x10 for phy4 sas: phy-4:4 added to port-4:0, phy_mask:0x10 (5000c5000792fbdd) sas: DOING DISCOVERY on port 0, pid:956 scsi 4:0:0:0: Direct-Access SEAGATE ST373455SS 0002 PQ: 0 ANSI: 5 sas: DONE DISCOVERY on port 0, pid:956, result:0 sas: DONE DISCOVERY on port 0, pid:956, result:0 aic94xx: control_phy_tasklet_complete: phy0: no device present: oob_status:0x0 aic94xx: control_phy_tasklet_complete: phy1: no device present: oob_status:0x0 aic94xx: control_phy_tasklet_complete: phy2: no device present: oob_status:0x0 aic94xx: control_phy_tasklet_complete: phy3: no device present: oob_status:0x0 aic94xx: control_phy_tasklet_complete: phy6: no device present: oob_status:0x0 aic94xx: control_phy_tasklet_complete: phy7: no device present: oob_status:0x0 aic94xx: escb_tasklet_complete: phy5: BYTES_DMAED aic94xx: STP proto device-to-host FIS: aic94xx: 00: 34 00 50 01 aic94xx: 04: 01 00 00 00 aic94xx: 08: 00 00 00 00 aic94xx: 0c: 01 00 00 00 aic94xx: 10: 00 00 00 00 aic94xx: asd_form_port: updating phy_mask 0x20 for phy5 sas: phy-4:5 added to port-4:1, phy_mask:0x20 (500e08100001b6cd) sas: DOING DISCOVERY on port 1, pid:956 sas: unhandled device 5 sas: DONE DISCOVERY on port 1, pid:956, result:-6 ACPI: ACPI0007:00 is registered as cooling_device0 ACPI: ACPI0007:01 is registered as cooling_device1 ACPI: ACPI0007:02 is registered as cooling_device2 ACPI: ACPI0007:03 is registered as cooling_device3 Driver 'sd' needs updating - please use bus_type methods sd 4:0:0:0: [sda] 143374744 512-byte hardware sectors (73408 MB) sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] Mode Sense: b3 00 10 08 sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 4:0:0:0: [sda] 143374744 512-byte hardware sectors (73408 MB) sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] Mode Sense: b3 00 10 08 sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sda: sda1 sda2 sda3 sd 4:0:0:0: [sda] Attached SCSI disk e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 16 e100: eth0: e100_probe: addr 0xff6eb000, irq 16, MAC addr 00:e0:81:4b:5b:4b tg3.c:v3.87 (December 20, 2007) ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 26 (level, low) -> IRQ 26 scsi5 : pata_serverworks scsi6 : pata_serverworks ata5: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 ata6: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 ata5.01: ATAPI: DV-28E-R, 1.8A, max UDMA/33 ata5.01: configured for UDMA/33 scsi 5:0:1:0: CD-ROM TEAC DV-28E-R 1.8A PQ: 0 ANSI: 5 Uniform Multi-Platform E-IDE driver ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ... sd 4:0:0:0: Attached scsi generic sg0 type 0 scsi 5:0:1:0: Attached scsi generic sg1 type 5 ...
