On Tue, 19 Feb 2008, James Bottomley wrote:
> On Tue, 2008-02-19 at 18:35 -0800, Andrew Vasquez wrote:
> > On Tue, 19 Feb 2008, James Bottomley wrote:
> >
> > > On Tue, 2008-02-19 at 21:29 +0200, Adrian Bunk wrote:
> > > > This patch removes dead code spotted by the Coverity checker.
> > > >
> > > > Signed-off-by: Adrian Bunk <bunk@xxxxxxxxxx>
> > > >
> > > > ---
> > > >
> > > > drivers/scsi/qla4xxx/ql4_isr.c | 18 +-----------------
> > > > 1 file changed, 1 insertion(+), 17 deletions(-)
> > > >
> > > > --- linux-2.6/drivers/scsi/qla4xxx/ql4_isr.c.old 2008-02-19 20:29:16.000000000 +0200
> > > > +++ linux-2.6/drivers/scsi/qla4xxx/ql4_isr.c 2008-02-19 20:30:37.000000000 +0200
> > > > @@ -91,38 +91,22 @@ static void qla4xxx_status_entry(struct
> > > > if (scsi_status == 0) {
> > > > cmd->result = DID_OK << 16;
> > > > break;
> > > > }
> > > >
> > > > if (sts_entry->iscsiFlags & ISCSI_FLAG_RESIDUAL_OVER) {
> > > > cmd->result = DID_ERROR << 16;
> > > > break;
> > > > }
> > > >
> > > > - if (sts_entry->iscsiFlags &ISCSI_FLAG_RESIDUAL_UNDER) {
> > > > + if (sts_entry->iscsiFlags &ISCSI_FLAG_RESIDUAL_UNDER)
> > > > scsi_set_resid(cmd, residual);
> > > > - if (!scsi_status && ((scsi_bufflen(cmd) - residual) <
> > > > - cmd->underflow)) {
> > > > -
> > > > - cmd->result = DID_ERROR << 16;
> > > > -
> > > > - DEBUG2(printk("scsi%ld:%d:%d:%d: %s: "
> > > > - "Mid-layer Data underrun0, "
> > > > - "xferlen = 0x%x, "
> > > > - "residual = 0x%x\n", ha->host_no,
> > > > - cmd->device->channel,
> > > > - cmd->device->id,
> > > > - cmd->device->lun, __func__,
> > > > - scsi_bufflen(cmd), residual));
> > > > - break;
> > > > - }
> > > > - }
> > >
> > > This code doesn't look dead to me, it looks to be enforcing
> > > cmd->underrun if set ... what makes the coverity checker think it can
> > > never be executed?
> >
> > Hmm, guess it's the earlier 'if (scsi_status == 0)' check a few lines
> > up... Dave S., can you take a look at this... Thanks, av
>
> Ah, so the !scsi_status is wrong it was supposed to be scsi_status !=
> 0 ... and even then it can just be dropped.
My guess is that the check should have been written as:
...
if (sts_entry->iscsiFlags &ISCSI_FLAG_RESIDUAL_UNDER)
scsi_set_resid(cmd, residual);
if ((scsi_bufflen(cmd) - residual) < cmd->underflow) {
...
It looks to be a logic-error while porting from qla2xxx, where
scsi_status during CS_COMPLETE is the full 16-bit status (high-byte is
transport, low-byte SCSI status) from from the FCP_RSP frame (not so
in iSCSI, where it's just the SCSI-status) and the residual check
in qla_isr.c::qla2x00_status_entry() looks like:
if (!lscsi_status &&
((unsigned)(scsi_bufflen(cp) - resid) <
cp->underflow)) {
...
I'll defer to Dave S. for verification.
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
