From: Linas Vepstas <linas@xxxxxxxxxxxxxx>
This patch adds the PCI error recovery callbacks to the Symbios SCSI device
driver. It includes support for First Failure Data Capture.
Signed-off-by: Linas Vepstas <linas@xxxxxxxxxxxxxx>
Assorted changes to initial patches, including returning IRQ_NONE from the
interrupt handler if the device is offline and re-using the eh_done completion
in the scsi error handler.
Signed-off-by: Matthew Wilcox <willy@xxxxxxxxxxxxxxx>
---
drivers/scsi/sym53c8xx_2/sym_glue.c | 179 ++++++++++++++++++++++++++++++++++-
drivers/scsi/sym53c8xx_2/sym_glue.h | 3 +
drivers/scsi/sym53c8xx_2/sym_hipd.c | 25 ++++-
3 files changed, 200 insertions(+), 7 deletions(-)
diff --git a/drivers/scsi/sym53c8xx_2/sym_glue.c b/drivers/scsi/sym53c8xx_2/sym_glue.c
index 6bc8789..fec9c9c 100644
--- a/drivers/scsi/sym53c8xx_2/sym_glue.c
+++ b/drivers/scsi/sym53c8xx_2/sym_glue.c
@@ -134,7 +134,7 @@ static struct scsi_transport_template *sym2_transport_template = NULL;
* Driver private area in the SCSI command structure.
*/
struct sym_ucmd { /* Override the SCSI pointer structure */
- struct completion *eh_done; /* For error handling */
+ struct completion *eh_done; /* SCSI error handling */
};
#define SYM_UCMD_PTR(cmd) ((struct sym_ucmd *)(&(cmd)->SCp))
@@ -556,6 +556,10 @@ static irqreturn_t sym53c8xx_intr(int irq, void *dev_id)
{
struct sym_hcb *np = dev_id;
+ /* Avoid spinloop trying to handle interrupts on frozen device */
+ if (pci_channel_offline(np->s.device))
+ return IRQ_NONE;
+
if (DEBUG_FLAGS & DEBUG_TINY) printf_debug ("[");
spin_lock(np->s.host->host_lock);
@@ -598,6 +602,7 @@ static int sym_eh_handler(int op, char *opname, struct scsi_cmnd *cmd)
struct sym_hcb *np = SYM_SOFTC_PTR(cmd);
struct sym_ucmd *ucmd = SYM_UCMD_PTR(cmd);
struct Scsi_Host *host = cmd->device->host;
+ struct pci_dev *pdev = np->s.device;
SYM_QUEHEAD *qp;
int cmd_queued = 0;
int sts = -1;
@@ -605,6 +610,38 @@ static int sym_eh_handler(int op, char *opname, struct scsi_cmnd *cmd)
dev_warn(&cmd->device->sdev_gendev, "%s operation started.\n", opname);
+ /* We may be in an error condition because the PCI bus
+ * went down. In this case, we need to wait until the
+ * PCI bus is reset, the card is reset, and only then
+ * proceed with the scsi error recovery. There's no
+ * point in hurrying; take a leisurely wait.
+ */
+#define WAIT_FOR_PCI_RECOVERY 35
+ if (pci_channel_offline(pdev)) {
+ struct host_data *hostdata = shost_priv(host);
+ struct completion *io_reset;
+ int finished_reset = 0;
+ init_completion(&eh_done);
+ spin_lock_irq(host->host_lock);
+ /* Make sure we didn't race */
+ if (pci_channel_offline(pdev)) {
+ if (!hostdata->io_reset)
+ hostdata->io_reset = &eh_done;
+ io_reset = hostdata->io_reset;
+ } else {
+ io_reset = NULL;
+ }
+
+ if (!pci_channel_offline(pdev))
+ finished_reset = 1;
+ spin_unlock_irq(host->host_lock);
+ if (!finished_reset)
+ finished_reset = wait_for_completion_timeout(io_reset,
+ WAIT_FOR_PCI_RECOVERY*HZ);
+ if (!finished_reset)
+ return SCSI_FAILED;
+ }
+
spin_lock_irq(host->host_lock);
/* This one is queued in some place -> to wait for completion */
FOR_EACH_QUEUED_ELEMENT(&np->busy_ccbq, qp) {
@@ -630,7 +667,7 @@ static int sym_eh_handler(int op, char *opname, struct scsi_cmnd *cmd)
break;
case SYM_EH_HOST_RESET:
sym_reset_scsi_bus(np, 0);
- sym_start_up (np, 1);
+ sym_start_up(np, 1);
sts = 0;
break;
default:
@@ -1435,7 +1472,7 @@ static struct Scsi_Host * __devinit sym_attach(struct scsi_host_template *tpnt,
/*
* Start the SCRIPTS.
*/
- sym_start_up (np, 1);
+ sym_start_up(np, 1);
/*
* Start the timer daemon
@@ -1822,6 +1859,134 @@ static void __devexit sym2_remove(struct pci_dev *pdev)
attach_count--;
}
+/**
+ * sym2_io_error_detected() - called when PCI error is detected
+ * @pdev: pointer to PCI device
+ * @state: current state of the PCI slot
+ */
+static pci_ers_result_t sym2_io_error_detected(struct pci_dev *pdev,
+ enum pci_channel_state state)
+{
+ /* If slot is permanently frozen, turn everything off */
+ if (state == pci_channel_io_perm_failure) {
+ sym2_remove(pdev);
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+
+ disable_irq(pdev->irq);
+ pci_disable_device(pdev);
+
+ /* Request that MMIO be enabled, so register dump can be taken. */
+ return PCI_ERS_RESULT_CAN_RECOVER;
+}
+
+/**
+ * sym2_io_slot_dump - Enable MMIO and dump debug registers
+ * @pdev: pointer to PCI device
+ */
+static pci_ers_result_t sym2_io_slot_dump(struct pci_dev *pdev)
+{
+ struct sym_hcb *np = pci_get_drvdata(pdev);
+
+ sym_dump_registers(np);
+
+ /* Request a slot reset. */
+ return PCI_ERS_RESULT_NEED_RESET;
+}
+
+/**
+ * sym2_reset_workarounds - hardware-specific work-arounds
+ *
+ * This routine is similar to sym_set_workarounds(), except
+ * that, at this point, we already know that the device was
+ * succesfully intialized at least once before, and so most
+ * of the steps taken there are un-needed here.
+ */
+static void sym2_reset_workarounds(struct pci_dev *pdev)
+{
+ u_char revision;
+ u_short status_reg;
+ struct sym_chip *chip;
+
+ pci_read_config_byte(pdev, PCI_CLASS_REVISION, &revision);
+ chip = sym_lookup_chip_table(pdev->device, revision);
+
+ /* Work around for errant bit in 895A, in a fashion
+ * similar to what is done in sym_set_workarounds().
+ */
+ pci_read_config_word(pdev, PCI_STATUS, &status_reg);
+ if (!(chip->features & FE_66MHZ) && (status_reg & PCI_STATUS_66MHZ)) {
+ status_reg = PCI_STATUS_66MHZ;
+ pci_write_config_word(pdev, PCI_STATUS, status_reg);
+ pci_read_config_word(pdev, PCI_STATUS, &status_reg);
+ }
+}
+
+/**
+ * sym2_io_slot_reset() - called when the pci bus has been reset.
+ * @pdev: pointer to PCI device
+ *
+ * Restart the card from scratch.
+ */
+static pci_ers_result_t sym2_io_slot_reset(struct pci_dev *pdev)
+{
+ struct sym_hcb *np = pci_get_drvdata(pdev);
+
+ printk(KERN_INFO "%s: recovering from a PCI slot reset\n",
+ sym_name(np));
+
+ if (pci_enable_device(pdev)) {
+ printk(KERN_ERR "%s: Unable to enable after PCI reset\n",
+ sym_name(np));
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+
+ pci_set_master(pdev);
+ enable_irq(pdev->irq);
+
+ /* If the chip can do Memory Write Invalidate, enable it */
+ if (np->features & FE_WRIE) {
+ if (pci_set_mwi(pdev))
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+
+ /* Perform work-arounds, analogous to sym_set_workarounds() */
+ sym2_reset_workarounds(pdev);
+
+ /* Perform host reset only on one instance of the card */
+ if (PCI_FUNC(pdev->devfn) == 0) {
+ if (sym_reset_scsi_bus(np, 0)) {
+ printk(KERN_ERR "%s: Unable to reset scsi host\n",
+ sym_name(np));
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+ sym_start_up(np, 1);
+ }
+
+ return PCI_ERS_RESULT_RECOVERED;
+}
+
+/**
+ * sym2_io_resume() - resume normal ops after PCI reset
+ * @pdev: pointer to PCI device
+ *
+ * Called when the error recovery driver tells us that its
+ * OK to resume normal operation. Use completion to allow
+ * halted scsi ops to resume.
+ */
+static void sym2_io_resume(struct pci_dev *pdev)
+{
+ struct sym_hcb *np = pci_get_drvdata(pdev);
+ struct Scsi_Host *shost = np->s.host;
+ struct host_data *hostdata = shost_priv(shost);
+
+ spin_lock_irq(shost->host_lock);
+ if (hostdata->io_reset)
+ complete_all(hostdata->io_reset);
+ hostdata->io_reset = NULL;
+ spin_unlock_irq(shost->host_lock);
+}
+
static void sym2_get_signalling(struct Scsi_Host *shost)
{
struct sym_hcb *np = sym_get_hcb(shost);
@@ -1984,11 +2149,19 @@ static struct pci_device_id sym2_id_table[] __devinitdata = {
MODULE_DEVICE_TABLE(pci, sym2_id_table);
+static struct pci_error_handlers sym2_err_handler = {
+ .error_detected = sym2_io_error_detected,
+ .mmio_enabled = sym2_io_slot_dump,
+ .slot_reset = sym2_io_slot_reset,
+ .resume = sym2_io_resume,
+};
+
static struct pci_driver sym2_driver = {
.name = NAME53C8XX,
.id_table = sym2_id_table,
.probe = sym2_probe,
.remove = __devexit_p(sym2_remove),
+ .err_handler = &sym2_err_handler,
};
static int __init sym2_init(void)
diff --git a/drivers/scsi/sym53c8xx_2/sym_glue.h b/drivers/scsi/sym53c8xx_2/sym_glue.h
index bea7bcc..d5ba5aa 100644
--- a/drivers/scsi/sym53c8xx_2/sym_glue.h
+++ b/drivers/scsi/sym53c8xx_2/sym_glue.h
@@ -40,6 +40,7 @@
#ifndef SYM_GLUE_H
#define SYM_GLUE_H
+#include <linux/completion.h>
#include <linux/delay.h>
#include <linux/ioport.h>
#include <linux/pci.h>
@@ -220,6 +221,7 @@ struct sym_device {
*/
struct host_data {
struct sym_hcb *ncb;
+ struct completion *io_reset; /* PCI error handling */
};
static inline struct sym_hcb * sym_get_hcb(struct Scsi_Host *host)
@@ -265,5 +267,6 @@ void sym_xpt_async_bus_reset(struct sym_hcb *np);
void sym_xpt_async_sent_bdr(struct sym_hcb *np, int target);
int sym_setup_data_and_start (struct sym_hcb *np, struct scsi_cmnd *csio, struct sym_ccb *cp);
void sym_log_bus_error(struct sym_hcb *np);
+void sym_dump_registers(struct sym_hcb *np);
#endif /* SYM_GLUE_H */
diff --git a/drivers/scsi/sym53c8xx_2/sym_hipd.c b/drivers/scsi/sym53c8xx_2/sym_hipd.c
index 21cd4c7..af24c44 100644
--- a/drivers/scsi/sym53c8xx_2/sym_hipd.c
+++ b/drivers/scsi/sym53c8xx_2/sym_hipd.c
@@ -1180,10 +1180,10 @@ static void sym_log_hard_error(struct sym_hcb *np, u_short sist, u_char dstat)
scr_to_cpu((int) *(u32 *)(script_base + script_ofs)));
}
- printf ("%s: regdump:", sym_name(np));
- for (i=0; i<24;i++)
- printf (" %02x", (unsigned)INB_OFF(np, i));
- printf (".\n");
+ printf("%s: regdump:", sym_name(np));
+ for (i = 0; i < 24; i++)
+ printf(" %02x", (unsigned)INB_OFF(np, i));
+ printf(".\n");
/*
* PCI BUS error.
@@ -1192,6 +1192,16 @@ static void sym_log_hard_error(struct sym_hcb *np, u_short sist, u_char dstat)
sym_log_bus_error(np);
}
+void sym_dump_registers(struct sym_hcb *np)
+{
+ u_short sist;
+ u_char dstat;
+
+ sist = INW(np, nc_sist);
+ dstat = INB(np, nc_dstat);
+ sym_log_hard_error(np, sist, dstat);
+}
+
static struct sym_chip sym_dev_table[] = {
{PCI_DEVICE_ID_NCR_53C810, 0x0f, "810", 4, 8, 4, 64,
FE_ERL}
@@ -2809,6 +2819,13 @@ void sym_interrupt (struct sym_hcb *np)
dstat |= INB(np, nc_dstat);
istatc = INB(np, nc_istat);
istat |= istatc;
+
+ /* Prevent deadlock waiting on a condition that may
+ * never clear. */
+ if (unlikely(sist == 0xffff && dstat == 0xff)) {
+ if (pci_channel_offline(np->s.device))
+ return;
+ }
} while (istatc & (SIP|DIP));
if (DEBUG_FLAGS & DEBUG_TINY)
--
1.4.4.2
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
