[PATCH v2 2/7] scsi: ufs: ufs-qcom: Setup host power mode during init

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Can Guo <quic_cang@xxxxxxxxxxx>

Setup host power mode and its limitations during UFS host driver init to
avoid repetitive work during every power mode change.

Co-developed-by: Bao D. Nguyen <quic_nguyenb@xxxxxxxxxxx>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@xxxxxxxxxxx>
Signed-off-by: Can Guo <quic_cang@xxxxxxxxxxx>
---
 drivers/ufs/host/ufs-qcom.c | 22 ++++++++++++++--------
 drivers/ufs/host/ufs-qcom.h |  1 +
 2 files changed, 15 insertions(+), 8 deletions(-)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index aee66a3..cc0eb37 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -898,7 +898,7 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 				struct ufs_pa_layer_attr *dev_req_params)
 {
 	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
-	struct ufs_host_params host_params;
+	struct ufs_host_params *host_params = &host->host_params;
 	int ret = 0;
 
 	if (!dev_req_params) {
@@ -908,13 +908,7 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 
 	switch (status) {
 	case PRE_CHANGE:
-		ufshcd_init_host_param(&host_params);
-		host_params.hs_rate = UFS_QCOM_LIMIT_HS_RATE;
-
-		/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
-		host_params.hs_tx_gear = host_params.hs_rx_gear = ufs_qcom_get_hs_gear(hba);
-
-		ret = ufshcd_negotiate_pwr_param(&host_params, dev_max_params, dev_req_params);
+		ret = ufshcd_negotiate_pwr_param(host_params, dev_max_params, dev_req_params);
 		if (ret) {
 			dev_err(hba->dev, "%s: failed to determine capabilities\n",
 					__func__);
@@ -1049,6 +1043,17 @@ static void ufs_qcom_advertise_quirks(struct ufs_hba *hba)
 		hba->quirks |= UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
 }
 
+static void ufs_qcom_set_host_params(struct ufs_hba *hba)
+{
+	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
+	struct ufs_host_params *host_params = &host->host_params;
+
+	ufshcd_init_host_param(host_params);
+
+	/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
+	host_params->hs_tx_gear = host_params->hs_rx_gear = ufs_qcom_get_hs_gear(hba);
+}
+
 static void ufs_qcom_set_caps(struct ufs_hba *hba)
 {
 	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
@@ -1273,6 +1278,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)
 
 	ufs_qcom_set_caps(hba);
 	ufs_qcom_advertise_quirks(hba);
+	ufs_qcom_set_host_params(hba);
 
 	err = ufs_qcom_ice_init(host);
 	if (err)
diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
index 9950a00..ab94c54 100644
--- a/drivers/ufs/host/ufs-qcom.h
+++ b/drivers/ufs/host/ufs-qcom.h
@@ -240,6 +240,7 @@ struct ufs_qcom_host {
 
 	struct gpio_desc *device_reset;
 
+	struct ufs_host_params host_params;
 	u32 phy_gear;
 
 	bool esi_enabled;
-- 
2.7.4




[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]

  Powered by Linux