Just a small update, the module stuff turned out to be a separate,
unrelated regression. I bisected that one also (applying these
reverts
each time to allow me to boot) and reported it to Masahiro, who put in
a
fix for it here:
https://lore.kernel.org/all/20220809141117.641543-1-masahiroy@xxxxxxxxxx/
. So you can ignore that stuff. Are these two commits still planned
to
be reverted?
-------- Original Message --------
Subject: Re: [PATCH v3 0/5] Fix mpt3sas driver sparse warnings
Date: 2022-08-02 19:36
From: Damien Le Moal <damien.lemoal@xxxxxxxxxxxxxxxxxx>
To: matoro <matoro_mailinglist_kernel@xxxxxxxxx>, Sreekanth Reddy
<sreekanth.reddy@xxxxxxxxxxxx>
On 8/3/22 05:27, matoro wrote:
Hi folks, sorry for the lateness, unfortunately this is in fact
broken
on BE. I use mpt3sas on sparc and my drives fail to come up on 5.19,
bisected to this patchset. Reverting both of the endian-related
commits, b4efbec4c2a75b619fae4e8768be379e88c78687 and
7ab4d2441b952977556672c2fe3f4c2a698cbb37, allows it to boot.
However,
after booting, I can't load any modules - everything errors with
"disagrees about version of symbol module_layout". I have completely
wiped out kernel sources, the module tree, and the kernel image,
rebuilding both from scratch with ONLY the revert patch applied, but
I
still can't load any modules. Presumably it would work with
CONFIG_MODVERSIONS=n, but these CRC checks are there for a reason and
I
can't tell if it has something to do with the revert or not.
For b4efbec4c2a75b619fae4e8768be379e88c78687, removing the
cpu_to_le32()
call results in the bytes actually being reversed by writel()/readl()
for
your BE machine. So it looks like the values that need to be written
to
the HBA have to be in CPU endian, not le32. Should be easy to fix.
And for 7ab4d2441b952977556672c2fe3f4c2a698cbb37, this looks like the
same
problem.
I will be traveling and busy this week, but I can have a look at a fix
next Monday. If the Broadcom folks can send a fix faster than that,
that
is of course welcome :)
$ modprobe --dump-modversions
/lib/modules/5.19.0-gentoo-sparc64/kernel/fs/openpromfs/openpromfs.ko
|
grep "module_layout"
0xa6c23707 module_layout
$ grep "module_layout" /usr/src/linux/Module.symvers
0xa6c23707 module_layout vmlinux EXPORT_SYMBOL
If you need real hardware access and do not have any on hand, please
reach out and I can provide temporary access!
Here is the full error on vanilla 5.19:
mpt3sas version 42.100.00.00 loaded
mpt2sas_cm0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem
(32650280 kB)
mpt2sas_cm0: _base_wait_for_doorbell_not_used: failed due to timeout
count(5000), doorbell_reg(18000000)!
mpt2sas_cm0: CurrentHostPageSize is 0: Setting default host page size
to
4k
mpt2sas_cm0: MSI-X vectors supported: 1
no of cores: 64, max_msix_vectors: -1
mpt2sas_cm0: 0 1 1
mpt2sas_cm0: pci_alloc_irq_vectors failed (r=-22) !!!
mpt2sas_cm0: High IOPs queues : disabled
mpt2sas0: IO-APIC enabled: IRQ 4
mpt2sas_cm0: iomem(0x0000084100000000), mapped(0x(____ptrval____)),
size(16384)
mpt2sas_cm0: ioport(0x0000085100000000), size(256)
mpt2sas_cm0: doorbell is in use (line=6869)
mpt2sas_cm0: _base_get_ioc_facts: handshake failed (r=-14)
mpt2sas_cm0: failure at
drivers/scsi/mpt3sas/mpt3sas_scsih.c:12336/_scsih_probe()!
mpt2sas_cm1: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem
(32650280 kB)
mpt2sas_cm1: _base_wait_for_doorbell_not_used: failed due to timeout
count(5000), doorbell_reg(18000000)!
mpt2sas_cm1: CurrentHostPageSize is 0: Setting default host page size
to
4k
mpt2sas_cm1: MSI-X vectors supported: 1
no of cores: 64, max_msix_vectors: -1
mpt2sas_cm1: 0 1 1
mpt2sas_cm1: pci_alloc_irq_vectors failed (r=-22) !!!
mpt2sas_cm1: High IOPs queues : disabled
mpt2sas1: IO-APIC enabled: IRQ 5
mpt2sas_cm1: iomem(0x0000084120000000), mapped(0x(____ptrval____)),
size(16384)
mpt2sas_cm1: ioport(0x0000085100002000), size(256)
mpt2sas_cm1: doorbell is in use (line=6869)
mpt2sas_cm1: _base_get_ioc_facts: handshake failed (r=-14)
mpt2sas_cm1: failure at
drivers/scsi/mpt3sas/mpt3sas_scsih.c:12336/_scsih_probe()!
-------- Original Message --------
Subject: Re: [PATCH v3 0/5] Fix mpt3sas driver sparse warnings
Date: 2022-03-09 01:35
From: Sreekanth Reddy <sreekanth.reddy@xxxxxxxxxxxx>
To: "Martin K. Petersen" <martin.petersen@xxxxxxxxxx>
On Wed, Mar 9, 2022 at 9:26 AM Martin K. Petersen
<martin.petersen@xxxxxxxxxx> wrote:
Sreekanth,
This series fix (remove) all sparse warnings generated when
compiling
the mpt3sas driver. All warnings are related to __iomem access and
endianness.
Please review this series and validate the patch 5 modification.
Martin,
This patch set looks good, but before acknowledging this patch set I
just wanted to do some basic testing on a big endian machine.
Currently I don't have a big endian machine, internally I am checking
to get access to big endian machines. Meanwhile if anyone does a
basic
testing on any big endian machine then please let me know. I will add
the acknowledgement signature.
Thanks,
Sreekanth
Thanks!
--
Martin K. Petersen Oracle Linux Engineering
