Hello Eric ,
On Tue, 20 Mar 2007, Mr. James W. Laferriere wrote:
On Mon, 19 Mar 2007, Moore, Eric wrote:
On Saturday, March 17, 2007 2:33 PM, James W. Laferriere wrote:
Hello All , I am have been having this problem since I
purchased the
controller and after changing out the disks I thought were
the problem .
I am still getting the continous :
mptscsih: ioc1: attempting task abort! (sc=f7a64500)
scsi 3:0:4:0:
command: Inquiry: 12 00 00 00 60 00
mptbase: Initiating ioc1 recovery
mptscsih: ioc1: task abort: SUCCESS (sc=f7a64500)
target3:0:4: Domain Validation detected failure, dropping back
target3:0:4: Domain Validation skipping write tests
target3:0:4: Ending Domain Validation
target3:0:4: asynchronous
target3:0:5: Beginning Domain Validation
mptscsih: ioc0: attempting target reset! (sc=f7a64380)
The acutual device id's change and the driver
continously resets the
busses & starts all over .
The disks are in a HP DS-SL13R-BA 4354R 14drive ultra3
racKmount cabinet
w/ dualbus & dualps , Which seems to present a ID6 , That
does not show up in
any of the bus scans .
Now I have previously had the same cabinet with 18gb
disks which had the
same problem with this controller . BUT I also have a LSI
Logic / Symbios
Logic 53c1010 66MHz Ultra3 dual SCSI bus Adapter which works
flawlessly with the
18gb disks in this very same cabinet .
The cables for connecting the adapter(s) to tha cabinet
are less than 24
inches in length .
Would anyone please shed some light on what it is I am
doing wrong or
need to do or ....? Too have this controller recognise these
disk drives in
this cabinet .
There is a seperate mailing list for scsi releated issues, e.g.
linux-scsi@. I've posted a patch to address your issue several times,
however it seems its not been picked up by the scsi subsystem
maintainer. The last time it was posted was here:
http://marc.info/?l=linux-scsi&m=117089244809072&w=2 An alternative is
you could obtain our latest drivers from the LSI download site, where
these drivers should have this patch
http://www.lsilogic.com/cm/DownloadSearch.do.
Eric
Hello Eric , Fyi , linux-2.6.21-rc4 + mpt-fusion(*) patches from
Andrew Morton's patch tree . Still gives me the ever looping reset . But I
have just found sometrhing of interest one of the Powersuplies in the
cabiinet 'May be' failing . I have to test that to be satisfied that is the
case .
I'll report back soon on the PS & please look into this . There is
no reason for the driver to keep a system in loop over a failing drive set .
Tia , JimL
(*)
ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.21-rc4/2.6.21-rc4-mm1/broken-out/mpt-fusion-handle-pci-layer-error-on-resume.patch
ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.21-rc4/2.6.21-rc4-mm1/broken-out/mpt-fusion-handle-mpt_resume-failure-while-resuming.patch
Fyi , I finally dug out that old LSI22915A controller I have & attached
the HP racKmount cabinet with the 14 146GB disks & I am now looking at 14 New
devices in my udev dev tree (**) . After configuring in the SYM53C8xx_2 driver
of course .
Tho , I'd sure like to use my LSI22320 in a stock kernel .
Tia , JimL
(**)
dmesg | egrep -C3 -i '(scsi|target).*[23]'
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
Loading iSCSI transport class v2.0-724.
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec AIC7902 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
scsi 0:0:0:0: Direct-Access COMPAQ BB01811C9C 3B07 PQ: 0 ANSI: 2
target0:0:0: asynchronous
scsi0:A:0:0: Tagged Queuing enabled. Depth 4
target0:0:0: Beginning Domain Validation
target0:0:0: wide asynchronous
target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
target0:0:0: Domain Validation skipping write tests
target0:0:0: Ending Domain Validation
scsi 0:0:1:0: Direct-Access COMPAQ BB01811C9C 3B07 PQ: 0 ANSI: 2
target0:0:1: asynchronous
scsi0:A:1:0: Tagged Queuing enabled. Depth 4
target0:0:1: Beginning Domain Validation
target0:0:1: wide asynchronous
target0:0:1: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
target0:0:1: Domain Validation skipping write tests
target0:0:1: Ending Domain Validation
scsi 0:0:2:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target0:0:2: asynchronous
scsi0:A:2:0: Tagged Queuing enabled. Depth 4
target0:0:2: Beginning Domain Validation
target0:0:2: wide asynchronous
target0:0:2: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset
127)
target0:0:2: Ending Domain Validation
scsi 0:0:3:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target0:0:3: asynchronous
scsi0:A:3:0: Tagged Queuing enabled. Depth 4
target0:0:3: Beginning Domain Validation
target0:0:3: wide asynchronous
target0:0:3: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset
127)
target0:0:3: Ending Domain Validation
scsi 0:0:6:0: Processor SUPER GEM318 0 PQ: 0 ANSI: 2
target0:0:6: asynchronous
target0:0:6: Beginning Domain Validation
target0:0:6: Ending Domain Validation
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec AIC7902 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
Adaptec aacraid driver (1.1-5[2423]-mh3)
QLogic Fibre Channel HBA Driver
scsi 1:0:0:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target1:0:0: asynchronous
scsi1:A:0:0: Tagged Queuing enabled. Depth 4
target1:0:0: Beginning Domain Validation
target1:0:0: wide asynchronous
target1:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset
127)
target1:0:0: Ending Domain Validation
scsi 1:0:1:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target1:0:1: asynchronous
scsi1:A:1:0: Tagged Queuing enabled. Depth 4
target1:0:1: Beginning Domain Validation
target1:0:1: wide asynchronous
target1:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset
127)
target1:0:1: Ending Domain Validation
scsi 1:0:2:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target1:0:2: asynchronous
scsi1:A:2:0: Tagged Queuing enabled. Depth 4
target1:0:2: Beginning Domain Validation
target1:0:2: wide asynchronous
target1:0:2: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset
127)
sym0: <1010-66> rev 0x1 at pci 0000:04:01.0 irq 16
target1:0:2: Ending Domain Validation
sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
scsi 1:0:3:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target1:0:3: asynchronous
scsi1:A:3:0: Tagged Queuing enabled. Depth 4
target1:0:3: Beginning Domain Validation
sym0: SCSI BUS has been reset.
scsi2 : sym-2.2.3
target1:0:3: wide asynchronous
target1:0:3: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset
127)
target1:0:3: Ending Domain Validation
sym1: <1010-66> rev 0x1 at pci 0000:04:01.1 irq 17
sym1: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: handling phase mismatch from SCRIPTS.
sym1: SCSI BUS has been reset.
scsi3 : sym-2.2.3
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.10-rc1 Wed Feb 14 10:14:25 PST 2007
st: Version 20070203, fixed bufsize 32768, s/g segs 256
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
SCSI device sda: 35565080 512-byte hdwr sectors (18209 MB)
sda: Write Protect is off
sda: Mode Sense: f3 00 10 08
SCSI device sda: write cache: disabled, read cache: enabled, supports DPO and
FUA
SCSI device sda: 35565080 512-byte hdwr sectors (18209 MB)
sda: Write Protect is off
sda: Mode Sense: f3 00 10 08
SCSI device sda: write cache: disabled, read cache: enabled, supports DPO and
FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 35565080 512-byte hdwr sectors (18209 MB)
sdb: Write Protect is off
sdb: Mode Sense: f3 00 10 08
SCSI device sdb: write cache: disabled, read cache: enabled, supports DPO and
FUA
SCSI device sdb: 35565080 512-byte hdwr sectors (18209 MB)
sdb: Write Protect is off
sdb: Mode Sense: f3 00 10 08
SCSI device sdb: write cache: disabled, read cache: enabled, supports DPO and
FUA
sdb: sdb1 sdb2 sdb3
sd 0:0:1:0: Attached scsi disk sdb
SCSI device sdc: 287132440 512-byte hdwr sectors (147012 MB)
sdc: Write Protect is off
sdc: Mode Sense: b3 00 00 08
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdc: 287132440 512-byte hdwr sectors (147012 MB)
sdc: Write Protect is off
sdc: Mode Sense: b3 00 00 08
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdc: sdc1
sd 0:0:2:0: Attached scsi disk sdc
SCSI device sdd: 287132440 512-byte hdwr sectors (147012 MB)
sdd: Write Protect is off
sdd: Mode Sense: b3 00 00 08
SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdd: 287132440 512-byte hdwr sectors (147012 MB)
sdd: Write Protect is off
sdd: Mode Sense: b3 00 00 08
SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
--
sd 0:0:3:0: Attached scsi disk sdd
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
sd 0:0:2:0: Attached scsi generic sg2 type 0
sd 0:0:3:0: Attached scsi generic sg3 type 0
scsi 0:0:6:0: Attached scsi generic sg4 type 3
SCSI Media Changer driver v0.25
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.04
mptbase: Initiating ioc0 bringup
scsi 1:0:6:0: Processor SUPER GEM318 0 PQ: 0 ANSI: 2
target1:0:6: asynchronous
target1:0:6: Beginning Domain Validation
target1:0:6: Ending Domain Validation
ioc0: 53C1030: Capabilities={Initiator,Target}
scsi4 : ioc0: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=16
mptbase: Initiating ioc1 bringup
SCSI device sde: 287132440 512-byte hdwr sectors (147012 MB)
sde: Write Protect is off
sde: Mode Sense: b3 00 00 08
SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sde: 287132440 512-byte hdwr sectors (147012 MB)
sde: Write Protect is off
sde: Mode Sense: b3 00 00 08
SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sde: sde1
sd 1:0:0:0: Attached scsi disk sde
sd 1:0:0:0: Attached scsi generic sg5 type 0
SCSI device sdf: 287132440 512-byte hdwr sectors (147012 MB)
sdf: Write Protect is off
sdf: Mode Sense: b3 00 00 08
SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdf: 287132440 512-byte hdwr sectors (147012 MB)
sdf: Write Protect is off
sdf: Mode Sense: b3 00 00 08
SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdf: sdf1
ioc1: <5>sd 1:0:1:0: Attached scsi disk sdf
sd 1:0:1:0: Attached scsi generic sg6 type 0
SCSI device sdg: 287132440 512-byte hdwr sectors (147012 MB)
53C1030: Capabilities={Initiator,Target}
sdg: Write Protect is off
sdg: Mode Sense: b3 00 00 08
SCSI device sdg: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdg: 287132440 512-byte hdwr sectors (147012 MB)
sdg: Write Protect is off
sdg: Mode Sense: b3 00 00 08
SCSI device sdg: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdg: sdg1
sd 1:0:2:0: Attached scsi disk sdg
sd 1:0:2:0: Attached scsi generic sg7 type 0
SCSI device sdh: 287132440 512-byte hdwr sectors (147012 MB)
sdh: Write Protect is off
sdh: Mode Sense: b3 00 00 08
SCSI device sdh: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdh: 287132440 512-byte hdwr sectors (147012 MB)
sdh: Write Protect is off
sdh: Mode Sense: b3 00 00 08
SCSI device sdh: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdh: sdh1
sd 1:0:3:0: Attached scsi disk sdh
sd 1:0:3:0: Attached scsi generic sg8 type 0
scsi 1:0:6:0: Attached scsi generic sg9 type 3
target4:0:1: mpt_config failed
scsi 2:0:0:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target2:0:0: tagged command queuing enabled, command queue depth 16.
target2:0:0: Beginning Domain Validation
target2:0:0: asynchronous
target2:0:0: wide asynchronous
target2:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
scsi5 : ioc1: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=17
target2:0:0: Ending Domain Validation
scsi 2:0:1:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target2:0:1: tagged command queuing enabled, command queue depth 16.
target2:0:1: Beginning Domain Validation
target2:0:1: asynchronous
target2:0:1: wide asynchronous
target2:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:1: Ending Domain Validation
scsi 2:0:2:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target2:0:2: tagged command queuing enabled, command queue depth 16.
target2:0:2: Beginning Domain Validation
target2:0:2: asynchronous
target2:0:2: wide asynchronous
target2:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:2: Ending Domain Validation
scsi 2:0:3:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target2:0:3: tagged command queuing enabled, command queue depth 16.
target2:0:3: Beginning Domain Validation
target2:0:3: asynchronous
target2:0:3: wide asynchronous
scsi 3:0:0:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target3:0:0: tagged command queuing enabled, command queue depth 16.
target3:0:0: Beginning Domain Validation
target3:0:0: asynchronous
target2:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:0: wide asynchronous
target3:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:3: Ending Domain Validation
scsi 2:0:4:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target3:0:0: Ending Domain Validation
target2:0:4: tagged command queuing enabled, command queue depth 16.
scsi 3:0:1:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target3:0:1: tagged command queuing enabled, command queue depth 16.
target3:0:1: Beginning Domain Validation
target3:0:1: asynchronous
target2:0:4: Beginning Domain Validation
target2:0:4: asynchronous
target3:0:1: wide asynchronous
target3:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:4: wide asynchronous
target2:0:4: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:1: Ending Domain Validation
target2:0:4: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
scsi 3:0:2:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target3:0:2: tagged command queuing enabled, command queue depth 16.
target2:0:4: Ending Domain Validation
target3:0:2: Beginning Domain Validation
scsi 2:0:5:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target2:0:5: tagged command queuing enabled, command queue depth 16.
target2:0:5: Beginning Domain Validation
target2:0:5: asynchronous
target3:0:2: asynchronous
target2:0:5: wide asynchronous
target3:0:2: wide asynchronous
target2:0:5: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:5: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:5: Ending Domain Validation
target3:0:2: Ending Domain Validation
scsi 3:0:3:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target3:0:3: tagged command queuing enabled, command queue depth 16.
target3:0:3: Beginning Domain Validation
target3:0:3: asynchronous
target3:0:3: wide asynchronous
target3:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:3: Ending Domain Validation
scsi 3:0:4:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target3:0:4: tagged command queuing enabled, command queue depth 16.
target3:0:4: Beginning Domain Validation
target3:0:4: asynchronous
target3:0:4: wide asynchronous
target3:0:4: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:4: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:4: Ending Domain Validation
scsi 3:0:5:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target3:0:5: tagged command queuing enabled, command queue depth 16.
target3:0:5: Beginning Domain Validation
target3:0:5: asynchronous
target3:0:5: wide asynchronous
target3:0:5: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:5: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target3:0:5: Ending Domain Validation
scsi 2:0:8:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target2:0:8: tagged command queuing enabled, command queue depth 16.
target2:0:8: Beginning Domain Validation
target2:0:8: asynchronous
target2:0:8: wide asynchronous
target2:0:8: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:8: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target2:0:8: Ending Domain Validation
Fusion MPT FC Host driver 3.04.04
Fusion MPT SAS Host driver 3.04.04
Fusion MPT misc device (ioctl) driver 3.04.04
--
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
scsi 3:0:8:0: Direct-Access FUJITSU MAP3147NC 0108 PQ: 0 ANSI: 3
target3:0:8: tagged command queuing enabled, command queue depth 16.
target3:0:8: Beginning Domain Validation
target3:0:8: asynchronous
target3:0:8: wide asynchronous
target3:0:8: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
USB Universal Host Controller Interface driver v3.0
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
target3:0:8: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 17, io base 0x00001800
target3:0:8: Ending Domain Validation
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
--
input: PC Speaker as /class/input/input1
input: PS/2 Generic Mouse as /class/input/input2
isl1208 2-006f: chip found, driver version 0.2
SCSI device sdi: 287132440 512-byte hdwr sectors (147012 MB)
sdi: Write Protect is off
isl1208 2-006f: rtc core: registered isl1208 as rtc0
sdi: Mode Sense: b3 00 00 08
--
pIII_sse : 4009.000 MB/sec
raid5: using function: pIII_sse (4009.000 MB/sec)
md: multipath personality registered for level -4
SCSI device sdi: 287132440 512-byte hdwr sectors (147012 MB)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx
sdi: Write Protect is off
sdi: Mode Sense: b3 00 00 08
--
unknown partition table
sd 2:0:0:0: Attached scsi disk sdi
sd 2:0:0:0: Attached scsi generic sg10 type 0
SCSI device sdj: 287132440 512-byte hdwr sectors (147012 MB)
sdj: Write Protect is off
sdj: Mode Sense: b3 00 00 08
SCSI device sdj: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdj: 287132440 512-byte hdwr sectors (147012 MB)
sdj: Write Protect is off
sdj: Mode Sense: b3 00 00 08
SCSI device sdj: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdj: unknown partition table
sd 2:0:1:0: Attached scsi disk sdj
sd 2:0:1:0: Attached scsi generic sg11 type 0
SCSI device sdk: 287132440 512-byte hdwr sectors (147012 MB)
sdk: Write Protect is off
sdk: Mode Sense: b3 00 00 08
SCSI device sdk: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdk: 287132440 512-byte hdwr sectors (147012 MB)
sdk: Write Protect is off
sdk: Mode Sense: b3 00 00 08
SCSI device sdk: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdk: unknown partition table
sd 2:0:2:0: Attached scsi disk sdk
sd 2:0:2:0: Attached scsi generic sg12 type 0
SCSI device sdl: 287132440 512-byte hdwr sectors (147012 MB)
sdl: Write Protect is off
sdl: Mode Sense: b3 00 00 08
SCSI device sdl: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdl: 287132440 512-byte hdwr sectors (147012 MB)
sdl: Write Protect is off
sdl: Mode Sense: b3 00 00 08
SCSI device sdl: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdl: unknown partition table
sd 2:0:3:0: Attached scsi disk sdl
sd 2:0:3:0: Attached scsi generic sg13 type 0
SCSI device sdm: 287132440 512-byte hdwr sectors (147012 MB)
sdm: Write Protect is off
sdm: Mode Sense: b3 00 00 08
SCSI device sdm: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdm: 287132440 512-byte hdwr sectors (147012 MB)
sdm: Write Protect is off
sdm: Mode Sense: b3 00 00 08
SCSI device sdm: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdm: unknown partition table
sd 2:0:4:0: Attached scsi disk sdm
sd 2:0:4:0: Attached scsi generic sg14 type 0
SCSI device sdn: 287132440 512-byte hdwr sectors (147012 MB)
sdn: Write Protect is off
sdn: Mode Sense: b3 00 00 08
SCSI device sdn: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdn: 287132440 512-byte hdwr sectors (147012 MB)
sdn: Write Protect is off
sdn: Mode Sense: b3 00 00 08
SCSI device sdn: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdn: unknown partition table
sd 2:0:5:0: Attached scsi disk sdn
sd 2:0:5:0: Attached scsi generic sg15 type 0
SCSI device sdo: 287132440 512-byte hdwr sectors (147012 MB)
sdo: Write Protect is off
sdo: Mode Sense: b3 00 00 08
SCSI device sdo: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdo: 287132440 512-byte hdwr sectors (147012 MB)
sdo: Write Protect is off
sdo: Mode Sense: b3 00 00 08
SCSI device sdo: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdo: unknown partition table
sd 2:0:8:0: Attached scsi disk sdo
sd 2:0:8:0: Attached scsi generic sg16 type 0
SCSI device sdp: 287132440 512-byte hdwr sectors (147012 MB)
sdp: Write Protect is off
sdp: Mode Sense: b3 00 00 08
SCSI device sdp: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdp: 287132440 512-byte hdwr sectors (147012 MB)
sdp: Write Protect is off
sdp: Mode Sense: b3 00 00 08
SCSI device sdp: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdp: unknown partition table
sd 3:0:0:0: Attached scsi disk sdp
sd 3:0:0:0: Attached scsi generic sg17 type 0
SCSI device sdq: 287132440 512-byte hdwr sectors (147012 MB)
sdq: Write Protect is off
sdq: Mode Sense: b3 00 00 08
SCSI device sdq: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdq: 287132440 512-byte hdwr sectors (147012 MB)
sdq: Write Protect is off
sdq: Mode Sense: b3 00 00 08
SCSI device sdq: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdq: unknown partition table
sd 3:0:1:0: Attached scsi disk sdq
sd 3:0:1:0: Attached scsi generic sg18 type 0
SCSI device sdr: 287132440 512-byte hdwr sectors (147012 MB)
sdr: Write Protect is off
sdr: Mode Sense: b3 00 00 08
SCSI device sdr: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdr: 287132440 512-byte hdwr sectors (147012 MB)
sdr: Write Protect is off
sdr: Mode Sense: b3 00 00 08
SCSI device sdr: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdr: unknown partition table
sd 3:0:2:0: Attached scsi disk sdr
sd 3:0:2:0: Attached scsi generic sg19 type 0
SCSI device sds: 287132440 512-byte hdwr sectors (147012 MB)
sds: Write Protect is off
sds: Mode Sense: b3 00 00 08
SCSI device sds: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sds: 287132440 512-byte hdwr sectors (147012 MB)
sds: Write Protect is off
sds: Mode Sense: b3 00 00 08
SCSI device sds: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sds: unknown partition table
sd 3:0:3:0: Attached scsi disk sds
sd 3:0:3:0: Attached scsi generic sg20 type 0
SCSI device sdt: 287132440 512-byte hdwr sectors (147012 MB)
sdt: Write Protect is off
sdt: Mode Sense: b3 00 00 08
SCSI device sdt: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdt: 287132440 512-byte hdwr sectors (147012 MB)
sdt: Write Protect is off
sdt: Mode Sense: b3 00 00 08
SCSI device sdt: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdt: unknown partition table
sd 3:0:4:0: Attached scsi disk sdt
sd 3:0:4:0: Attached scsi generic sg21 type 0
SCSI device sdu: 287132440 512-byte hdwr sectors (147012 MB)
sdu: Write Protect is off
sdu: Mode Sense: b3 00 00 08
SCSI device sdu: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdu: 287132440 512-byte hdwr sectors (147012 MB)
sdu: Write Protect is off
sdu: Mode Sense: b3 00 00 08
SCSI device sdu: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdu: unknown partition table
sd 3:0:5:0: Attached scsi disk sdu
sd 3:0:5:0: Attached scsi generic sg22 type 0
SCSI device sdv: 287132440 512-byte hdwr sectors (147012 MB)
sdv: Write Protect is off
sdv: Mode Sense: b3 00 00 08
SCSI device sdv: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sdv: 287132440 512-byte hdwr sectors (147012 MB)
sdv: Write Protect is off
sdv: Mode Sense: b3 00 00 08
SCSI device sdv: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdv: unknown partition table
sd 3:0:8:0: Attached scsi disk sdv
sd 3:0:8:0: Attached scsi generic sg23 type 0
isl1208 2-006f: hctosys: invalid date/time
md: Autodetecting RAID arrays.
md: invalid raid superblock magic on sdc1
--
kjournald starting. Commit interval 5 seconds
EXT3 FS on md3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SCSI device sdi: 287132440 512-byte hdwr sectors (147012 MB)
sdi: Write Protect is off
sdi: Mode Sense: b3 00 00 08
SCSI device sdi: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdi: sdi1
SCSI device sdi: 287132440 512-byte hdwr sectors (147012 MB)
sdi: Write Protect is off
sdi: Mode Sense: b3 00 00 08
SCSI device sdi: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdi: sdi1
SCSI device sdj: 287132440 512-byte hdwr sectors (147012 MB)
sdj: Write Protect is off
sdj: Mode Sense: b3 00 00 08
SCSI device sdj: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdj: sdj1
SCSI device sdj: 287132440 512-byte hdwr sectors (147012 MB)
sdj: Write Protect is off
sdj: Mode Sense: b3 00 00 08
SCSI device sdj: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
--
+-----------------------------------------------------------------+
| James W. Laferriere | System Techniques | Give me VMS |
| Network Engineer | 663 Beaumont Blvd | Give me Linux |
| babydr@xxxxxxxxxxxxxxxx | Pacifica, CA. 94044 | only on AXP |
+-----------------------------------------------------------------+
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
