Andrew Morton wrote: > Yes, getting the oops traces will help, thanks. And confirmation on a more > recent kernel would be good. Here's what I get. I used netconsole so whatever was logged prior to it starting was lost. The PC is a suprtmicro x5da8 with an onboard dual channel AHA-39320 u320 controller. I have a dual channel AHA-39160 u160 and a dual channel AHA-2940U/UW (ch0/internal is wide/narrow, ch1/externel is narrow). I thought it was because I had option roms turned off, but when I turned them on, it still has problems. What's odd is the fact that if I boot with init=/bin/sh, modprobe aic7xxx, it works fine and I can exec init and it works fine. I have the logs when it failes and when it works, see below. The console log when it fails: ------------------------------------------------------------------------------ [ 22.802262] <Adaptec 3960D Ultra160 SCSI adapter> [ 22.802264] aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs [ 22.802265] [ 25.040283] scsi 2:0:0:0: Direct-Access SEAGATE SX150176LC BA12 PQ: 0 ANSI: 2 [ 25.040359] scsi2:A:0:0: Tagged Queuing enabled. Depth 32 [ 25.040449] target2:0:0: Beginning Domain Validation [ 25.045753] target2:0:0: wide asynchronous [ 25.049768] target2:0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 25.053043] target2:0:0: Domain Validation skipping write tests [ 25.053089] target2:0:0: Ending Domain Validation [ 25.057249] SCSI device sdd: 97693755 512-byte hdwr sectors (50019 MB) [ 25.059872] sdd: Write Protect is off [ 25.062420] SCSI device sdd: drive cache: write through w/ FUA [ 25.063275] SCSI device sdd: 97693755 512-byte hdwr sectors (50019 MB) [ 25.065868] sdd: Write Protect is off [ 25.068853] SCSI device sdd: drive cache: write through w/ FUA [ 25.068915] sdd: unknown partition table [ 25.084327] sd 2:0:0:0: Attached scsi disk sdd [ 25.094681] scsi 2:0:1:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 25.094768] scsi2:A:1:0: Tagged Queuing enabled. Depth 32 [ 25.094867] target2:0:1: Beginning Domain Validation [ 25.100679] target2:0:1: wide asynchronous [ 25.105894] target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 25.110233] target2:0:1: Domain Validation skipping write tests [ 25.110312] target2:0:1: Ending Domain Validation [ 25.125724] SCSI device sde: 97693755 512-byte hdwr sectors (50019 MB) [ 25.133748] sde: Write Protect is off [ 25.136491] SCSI device sde: drive cache: write through w/ FUA [ 25.137521] SCSI device sde: 97693755 512-byte hdwr sectors (50019 MB) [ 25.140189] sde: Write Protect is off [ 25.142882] SCSI device sde: drive cache: write through w/ FUA [ 25.142960] sde: unknown partition table [ 25.165486] sd 2:0:1:0: Attached scsi disk sde [ 25.172022] scsi 2:0:2:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 25.172116] scsi2:A:2:0: Tagged Queuing enabled. Depth 32 [ 25.172222] target2:0:2: Beginning Domain Validation [ 25.178504] target2:0:2: wide asynchronous [ 25.189460] target2:0:2: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 25.193309] target2:0:2: Domain Validation skipping write tests [ 25.193407] target2:0:2: Ending Domain Validation [ 25.203341] SCSI device sdf: 97693755 512-byte hdwr sectors (50019 MB) [ 25.205673] sdf: Write Protect is off [ 25.208401] SCSI device sdf: drive cache: write through w/ FUA [ 25.209368] SCSI device sdf: 97693755 512-byte hdwr sectors (50019 MB) [ 25.212067] sdf: Write Protect is off [ 25.214866] SCSI device sdf: drive cache: write through w/ FUA [ 25.214965] sdf: unknown partition table [ 25.233725] sd 2:0:2:0: Attached scsi disk sdf [ 25.243892] scsi 2:0:3:0: Direct-Access SEAGATE SX150176LC BA12 PQ: 0 ANSI: 2 [ 25.243991] scsi2:A:3:0: Tagged Queuing enabled. Depth 32 [ 25.244106] target2:0:3: Beginning Domain Validation [ 25.249550] target2:0:3: wide asynchronous [ 25.253758] target2:0:3: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 25.257254] target2:0:3: Domain Validation skipping write tests [ 25.257342] target2:0:3: Ending Domain Validation [ 25.264705] SCSI device sdg: 97693755 512-byte hdwr sectors (50019 MB) [ 25.269670] sdg: Write Protect is off [ 25.272365] SCSI device sdg: drive cache: write through w/ FUA [ 25.273277] SCSI device sdg: 97693755 512-byte hdwr sectors (50019 MB) [ 25.275906] sdg: Write Protect is off [ 25.278531] SCSI device sdg: drive cache: write through w/ FUA [ 25.278614] sdg: unknown partition table [ 25.297553] sd 2:0:3:0: Attached scsi disk sdg [ 25.306920] scsi 2:0:4:0: Direct-Access SEAGATE SX150176LC BA12 PQ: 0 ANSI: 2 [ 25.307062] scsi2:A:4:0: Tagged Queuing enabled. Depth 32 [ 25.307176] target2:0:4: Beginning Domain Validation [ 25.312696] target2:0:4: wide asynchronous [ 25.316827] target2:0:4: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 25.320227] target2:0:4: Domain Validation skipping write tests [ 25.320297] target2:0:4: Ending Domain Validation [ 25.324299] SCSI device sdh: 97693755 512-byte hdwr sectors (50019 MB) [ 25.329720] sdh: Write Protect is off [ 25.332454] SCSI device sdh: drive cache: write through w/ FUA [ 25.333429] SCSI device sdh: 97693755 512-byte hdwr sectors (50019 MB) [ 25.336077] sdh: Write Protect is off [ 25.338771] SCSI device sdh: drive cache: write through w/ FUA [ 25.338869] sdh: unknown partition table [ 25.359104] sd 2:0:4:0: Attached scsi disk sdh [ 27.442022] scsi 2:0:14:0: Processor SYMBIOS SYM2000 2 PQ: 0 ANSI: 2 [ 27.442146] target2:0:14: Beginning Domain Validation [ 27.442620] target2:0:14: Ending Domain Validation [ 27.715907] ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 49 (level, low) -> IRQ 20 [ 28.932735] scsi3 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 [ 28.932738] <Adaptec 3960D Ultra160 SCSI adapter> [ 28.932739] aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs [ 28.932741] [ 31.144275] scsi 3:0:0:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 31.144349] scsi3:A:0:0: Tagged Queuing enabled. Depth 32 [ 31.144435] target3:0:0: Beginning Domain Validation [ 31.149771] target3:0:0: wide asynchronous [ 31.153811] target3:0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 31.157108] target3:0:0: Domain Validation skipping write tests [ 31.157155] target3:0:0: Ending Domain Validation [ 31.165001] SCSI device sdi: 97693755 512-byte hdwr sectors (50019 MB) [ 31.167386] sdi: Write Protect is off [ 31.170053] SCSI device sdi: drive cache: write through w/ FUA [ 31.171047] SCSI device sdi: 97693755 512-byte hdwr sectors (50019 MB) [ 31.173749] sdi: Write Protect is off [ 31.177502] SCSI device sdi: drive cache: write through w/ FUA [ 31.177578] sdi: unknown partition table [ 31.195213] sd 3:0:0:0: Attached scsi disk sdi [ 31.206853] scsi 3:0:1:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 31.206931] scsi3:A:1:0: Tagged Queuing enabled. Depth 32 [ 31.207036] target3:0:1: Beginning Domain Validation [ 31.223265] target3:0:1: wide asynchronous [ 31.227425] target3:0:1: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 31.230835] target3:0:1: Domain Validation skipping write tests [ 31.230904] target3:0:1: Ending Domain Validation [ 31.234601] SCSI device sdj: 97693755 512-byte hdwr sectors (50019 MB) [ 31.236894] sdj: Write Protect is off [ 31.239667] SCSI device sdj: drive cache: write through w/ FUA [ 31.240835] SCSI device sdj: 97693755 512-byte hdwr sectors (50019 MB) [ 31.243557] sdj: Write Protect is off [ 31.249531] SCSI device sdj: drive cache: write through w/ FUA [ 31.249610] sdj: unknown partition table [ 31.270734] sd 3:0:1:0: Attached scsi disk sdj [ 31.283528] scsi 3:0:2:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 31.284432] scsi3:A:2:0: Tagged Queuing enabled. Depth 32 [ 31.284547] target3:0:2: Beginning Domain Validation [ 31.298487] target3:0:2: wide asynchronous [ 31.305033] target3:0:2: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 31.308464] target3:0:2: Domain Validation skipping write tests [ 31.308533] target3:0:2: Ending Domain Validation [ 31.316184] SCSI device sdk: 97693755 512-byte hdwr sectors (50019 MB) [ 31.319338] sdk: Write Protect is off [ 31.322105] SCSI device sdk: drive cache: write through w/ FUA [ 31.323146] SCSI device sdk: 97693755 512-byte hdwr sectors (50019 MB) [ 31.325842] sdk: Write Protect is off [ 31.329005] SCSI device sdk: drive cache: write through w/ FUA [ 31.329102] sdk: unknown partition table [ 31.349209] sd 3:0:2:0: Attached scsi disk sdk [ 31.359122] scsi 3:0:3:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 31.359242] scsi3:A:3:0: Tagged Queuing enabled. Depth 32 [ 31.359417] target3:0:3: Beginning Domain Validation [ 31.365700] target3:0:3: wide asynchronous [ 31.370023] target3:0:3: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 31.373668] target3:0:3: Domain Validation skipping write tests [ 31.373734] target3:0:3: Ending Domain Validation [ 31.385119] SCSI device sdl: 97693755 512-byte hdwr sectors (50019 MB) [ 31.387365] sdl: Write Protect is off [ 31.390054] SCSI device sdl: drive cache: write through w/ FUA [ 31.392132] SCSI device sdl: 97693755 512-byte hdwr sectors (50019 MB) [ 31.394836] sdl: Write Protect is off [ 31.398006] SCSI device sdl: drive cache: write through w/ FUA [ 31.398108] sdl: unknown partition table [ 31.420194] sd 3:0:3:0: Attached scsi disk sdl [ 31.434188] scsi 3:0:4:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 31.434308] scsi3:A:4:0: Tagged Queuing enabled. Depth 32 [ 31.434469] target3:0:4: Beginning Domain Validation [ 31.439914] target3:0:4: wide asynchronous [ 31.444090] target3:0:4: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 31.447536] target3:0:4: Domain Validation skipping write tests [ 31.447606] target3:0:4: Ending Domain Validation [ 31.450531] SCSI device sdm: 97693755 512-byte hdwr sectors (50019 MB) [ 31.452756] sdm: Write Protect is off [ 31.455505] SCSI device sdm: drive cache: write through w/ FUA [ 31.456542] SCSI device sdm: 97693755 512-byte hdwr sectors (50019 MB) [ 31.459668] sdm: Write Protect is off [ 31.462448] SCSI device sdm: drive cache: write through w/ FUA [ 31.462545] sdm: unknown partition table [ 31.478519] sd 3:0:4:0: Attached scsi disk sdm [ 33.542811] scsi 3:0:14:0: Processor SYMBIOS SYM2000 2 PQ: 0 ANSI: 2 [ 33.542942] target3:0:14: Beginning Domain Validation [ 33.543501] target3:0:14: Ending Domain Validation [ 33.831621] ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 16 (level, low) -> IRQ 21 [ 34.847248] scsi4 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 [ 34.847251] <Adaptec 2940/DUAL Ultra SCSI adapter> [ 34.847252] aic7895: Ultra Wide Channel A, SCSI Id=7, 32/253 SCBs [ 34.847253] [ 35.396894] scsi 4:0:2:0: CD-ROM PLEXTOR CD-ROM PX-40TS 1.11 PQ: 0 ANSI: 2 [ 35.397007] target4:0:2: Beginning Domain Validation [ 35.403496] target4:0:2: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15) [ 35.408906] target4:0:2: Domain Validation skipping write tests [ 35.408972] target4:0:2: Ending Domain Validation [ 35.427265] scsi 4:0:3:0: CD-ROM PLEXTOR CD-R PX-W4012S 1.01 PQ: 0 ANSI: 2 [ 35.427407] target4:0:3: Beginning Domain Validation [ 35.429785] target4:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15) [ 35.434272] target4:0:3: Domain Validation skipping write tests [ 35.434336] target4:0:3: Ending Domain Validation [ 35.457701] scsi 4:0:4:0: CD-ROM NAKAMICH MJ-5.16S 1.07 PQ: 0 ANSI: 2 [ 35.457864] target4:0:4: Beginning Domain Validation [ 35.474212] target4:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) [ 35.483112] target4:0:4: Domain Validation skipping write tests [ 35.483187] target4:0:4: Ending Domain Validation [ 35.489845] scsi 4:0:4:1: CD-ROM NAKAMICH MJ-5.16S 1.07 PQ: 0 ANSI: 2 [ 35.489970] target4:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) [ 35.504490] scsi 4:0:4:2: CD-ROM NAKAMICH MJ-5.16S 1.07 PQ: 0 ANSI: 2 [ 35.504630] target4:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) [ 35.531322] scsi 4:0:4:3: CD-ROM NAKAMICH MJ-5.16S 1.07 PQ: 0 ANSI: 2 [ 35.531457] target4:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) [ 35.543143] scsi 4:0:4:4: CD-ROM NAKAMICH MJ-5.16S 1.07 PQ: 0 ANSI: 2 [ 35.543272] target4:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) [ 35.645497] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray [ 35.645566] Uniform CD-ROM driver Revision: 3.20 [ 37.736693] scsi 4:0:5:0: CD-ROM YAMAHA CRW8424S 1.0d PQ: 0 ANSI: 2 [ 37.736778] target4:0:5: Beginning Domain Validation [ 37.755233] target4:0:5: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15) [ 37.764863] target4:0:5: Domain Validation skipping write tests [ 37.764910] target4:0:5: Ending Domain Validation [ 40.154122] ACPI: PCI Interrupt 0000:05:01.1[B] -> GSI 17 (level, low) -> IRQ 22 [ 40.158190] scsi4: PCI error Interrupt at seqaddr = 0x1bb [ 40.158261] scsi4: Signaled a Target Abort [ 40.158777] sr1: scsi-1 drive [ 40.159611] scsi4:A:3:0: ahc_intr - referenced scb not valid during seqint 0x71 scb(255) [ 40.159719] >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<< [ 40.159720] scsi4: Dumping Card State in Message-in phase, at SEQADDR 0x1bb [ 40.159838] Card was paused [ 40.159888] ACCUM = 0x0, SINDEX = 0x71, DINDEX = 0xe4, ARG_2 = 0x0 [ 40.159940] HCNT = 0x8 SCBPTR = 0x0 [ 40.159993] SCSISIGI[0xe6]:(REQI|BSYI|MSGI|IOI|CDI) [ 40.160298] ERROR[0x40]:(PCIERRSTAT) SCSIBUSL[0x0] [ 40.160534] LASTPHASE[0xe0]:(MSGI|IOI|CDI) SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) [ 40.160914] SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0xf]:(SXFR_ULTRA2) [ 40.161187] SEQCTL[0x10]:(FASTMODE) SEQ_FLAGS[0x0] [ 40.161420] SSTAT0[0x6]:(SPIORDY|SDONE) SSTAT1[0x3]:(REQINIT|PHASECHG) [ 40.161742] SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x0] [ 40.162003] SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST|ENSELTIMO) [ 40.162271] SXFRCTL0[0xa8]:(SPIOEN|FAST20|DFON) [ 40.162504] DFCNTRL[0x4]:(DIRECTION) DFSTATUS[0x65]:(FIFOEMP|DFTHRESH|FIFOQWDEMP|DFCACHETH) [ 40.162870] STACK: 0x114 0x0 0x179 0x18f [ 40.163058] SCB count = 4 [ 40.163142] Kernel NEXTQSCB = 3 [ 40.163188] Card NEXTQSCB = 3 [ 40.163233] QINFIFO entries: [ 40.163322] Waiting Queue entries: [ 40.163408] Disconnected Queue entries: [ 40.163491] QOUTFIFO entries: [ 40.163582] Sequencer Free SCB List: 1 [ 40.163712] Sequencer SCB Info: [ 40.163761] 0 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.164330] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.164623] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.164911] 1 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.165430] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.165698] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.165971] 2 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.166476] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.166724] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.166949] 3 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.167435] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.167683] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.167927] 4 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.168435] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.168708] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.168971] 5 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.169556] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.170055] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.170290] 6 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.170775] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.171011] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.171236] 7 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.171695] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.171921] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.172139] 8 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.172592] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.172815] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.173034] 9 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.173487] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.173711] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.173946] 10 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.174403] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.174626] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.174847] 11 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.175299] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.175524] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.175747] 12 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.177129] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.177392] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.177622] 13 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.178111] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.178337] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.178551] 14 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.179026] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.179268] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.179491] 15 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.180118] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.180329] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.180536] 16 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.180963] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.181174] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.181381] 17 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.181808] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) [ 40.182023] SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] [ 40.182229] 18 SCB_CONTROL[0xff]:(DISCONNECTED|ULTRAENB|MK_MESSAGE|TAG_ENB|DISCENB|TARGET_SCB|SCB_TAG_TYPE) [ 40.182657] SCB_SCSIID[0xff][ 40.195507] [<c011b69d>] [ 40.195587] [<f8859af4>] ahc_handle_seqint+0x16af/0x2bea [aic7xxx] [ 40.195679] [<f883323e>] e1000_unmap_and_free_tx_resource+0x14/0x22 [e1000] [ 40.195768] [<f88348fe>] e1000_clean_tx_irq+0x68/0x259 [e1000] [ 40.195855] [<f8866d28>] ahc_linux_isr+0x22c/0x247 [aic7xxx] [ 40.195943] [<c013a18d>] handle_IRQ_event+0x31/0x5a [ 40.196025] [<c013b5c2>] handle_fasteoi_irq+0x73/0xbd [ 40.196105] [<c013b54f>] handle_fasteoi_irq+0x0/0xbd [ 40.196185] [<c01059ff>] do_IRQ+0x83/0xe4 [ 40.196267] [<c010397a>] common_interrupt+0x1a/0x20 [ 40.196348] [<f885da4f>] ahc_read_seeprom+0x23c/0x36e [aic7xxx] [ 40.196435] [<f885fe51>] ahc_pci_config+0x4ce/0x17c3 [aic7xxx] [ 40.196521] [<c010e400>] mp_register_gsi+0xe8/0x1ca [ 40.196600] [<c0256f51>] pci_conf1_read+0x85/0xc4 [ 40.196682] [<c025847d>] pci_read+0x3d/0x41 [ 40.196763] [<c01c74a1>] pci_bus_read_config_byte+0x5d/0x65 [ 40.196845] [<f886829c>] ahc_linux_pci_dev_probe+0xec/0x1e1 [aic7xxx] [ 40.196934] [<c0190960>] sysfs_dirent_exist+0x47/0x72 [ 40.197015] [<c019178d>] sysfs_create_link+0x75/0x180 [ 40.197225] [<c01cbd32>] pci_match_device+0x1e/0xd2 [ 40.197305] [<c0209199>] get_device+0x1b/0x24 [ 40.197385] [<c01cbe60>] pci_device_probe+0x51/0x6d [ 40.197465] [<c020b795>] really_probe+0x33/0xe2 [ 40.197545] [<c020b96e>] __driver_attach+0x0/0x8f [ 40.197626] [<c020b9fb>] __driver_attach+0x8d/0x8f [ 40.197705] [<c020acbc>] bus_for_each_dev+0x58/0x77 [ 40.197785] [<c020b695>] driver_attach+0x26/0x2a [ 40.197866] [<c020b96e>] __driver_attach+0x0/0x8f [ 40.197947] [<c020b086>] bus_add_driver+0x6c/0x1ab [ 40.198026] [<c020bba4>] driver_register+0x5e/0x95 [ 40.198106] [<c01cc018>] __pci_register_driver+0x8a/0xb2 [ 40.198187] [<f88681ac>] ahc_linux_pci_init+0x17/0x1b [aic7xxx] [ 40.198274] [<f881618e>] ahc_linux_init+0x18e/0x3b7 [aic7xxx] [ 40.198359] [<c0139a63>] __stop_machine_run+0x87/0xaf [ 40.198439] [<c02bc3da>] wait_for_completion+0x93/0x9a [ 40.198522] [<c0136f56>] sys_init_module+0x14c/0x1c56 [ 40.198606] [<c0102ff3>] syscall_call+0x7/0xb [ 40.198686] ======================= When it works (Full dmesg): ------------------------------------------------------------------------------ [ 0.000000] Linux version 2.6.19 (root@(none)) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #2 SMP PREEMPT Fri Feb 2 13:58:34 EST 2007 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009b400 (usable) [ 0.000000] BIOS-e820: 000000000009b400 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003ff70000 (usable) [ 0.000000] BIOS-e820: 000000003ff70000 - 000000003ff78000 (ACPI data) [ 0.000000] BIOS-e820: 000000003ff78000 - 000000003ff80000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved) [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) [ 0.000000] 127MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f61f0 [ 0.000000] Entering add_active_range(0, 0, 262000) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 262000 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 262000 [ 0.000000] On node 0 totalpages: 262000 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 254 pages used for memmap [ 0.000000] HighMem zone: 32370 pages, LIFO batch:7 [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP (v000 PTLTD ) @ 0x000f6180 [ 0.000000] ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x3ff73fb9 [ 0.000000] ACPI: FADT (v001 INTEL PLACER 0x06040000 PTL 0x00000008) @ 0x3ff77e78 [ 0.000000] ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x3ff77eec [ 0.000000] ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x3ff77f88 [ 0.000000] ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x3ff77fb0 [ 0.000000] ACPI: DSDT (v001 INTEL PLACER 0x06040000 MSFT 0x0100000e) @ 0x00000000 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:2 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x06] enabled) [ 0.000000] Processor #6 15:2 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 15:2 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled) [ 0.000000] Processor #7 15:2 APIC version 20 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec80000] gsi_base[24]) [ 0.000000] IOAPIC[1]: apic_id 3, version 32, address 0xfec80000, GSI 24-47 [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec80100] gsi_base[48]) [ 0.000000] IOAPIC[2]: apic_id 4, version 32, address 0xfec80100, GSI 48-71 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 3 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) [ 0.000000] Detected 2666.062 MHz processor. [ 55.250445] Built 1 zonelists. Total pages: 259954 [ 55.250448] Kernel command line: root=/dev/sda1 init=/bin/sh [ 55.250621] mapped APIC to ffffd000 (fee00000) [ 55.250624] mapped IOAPIC to ffffc000 (fec00000) [ 55.250626] mapped IOAPIC to ffffb000 (fec80000) [ 55.250629] mapped IOAPIC to ffffa000 (fec80100) [ 55.250632] Enabling fast FPU save and restore... done. [ 55.250635] Enabling unmasked SIMD FPU exception support... done. [ 55.250639] Initializing CPU#0 [ 55.250736] CPU 0 irqstacks, hard=c03af000 soft=c03ab000 [ 55.250739] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 55.251850] Console: colour VGA+ 80x25 [ 55.254826] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 55.255566] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 55.280544] Memory: 1035056k/1048000k available (1787k kernel code, 12304k reserved, 697k data, 208k init, 130496k highmem) [ 55.280613] virtual kernel memory layout: [ 55.280614] fixmap : 0xfff83000 - 0xfffff000 ( 496 kB) [ 55.280615] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 55.280616] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 55.280617] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 55.280618] .init : 0xc0372000 - 0xc03a6000 ( 208 kB) [ 55.280619] .data : 0xc02bed2f - 0xc036d434 ( 697 kB) [ 55.280620] .text : 0xc0100000 - 0xc02bed2f (1787 kB) [ 55.280963] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 55.358716] Calibrating delay using timer specific routine.. 5336.07 BogoMIPS (lpj=10672156) [ 55.358857] Mount-cache hash table entries: 512 [ 55.359038] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 [ 55.359050] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 55.359128] CPU: L2 cache: 512K [ 55.359171] CPU: Physical Processor ID: 0 [ 55.359215] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 [ 55.359223] Intel machine check architecture supported. [ 55.359270] Intel machine check reporting enabled on CPU#0. [ 55.359316] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available [ 55.359362] CPU0: Thermal monitoring enabled [ 55.359425] Checking 'hlt' instruction... OK. [ 55.374998] Freeing SMP alternatives: 12k freed [ 55.375043] ACPI: Core revision 20060707 [ 55.379527] CPU0: Intel(R) Xeon(TM) CPU 2.66GHz stepping 05 [ 55.379658] Booting processor 1/1 eip 2000 [ 55.379703] CPU 1 irqstacks, hard=c03b0000 soft=c03ac000 [ 55.390041] Initializing CPU#1 [ 55.470689] Calibrating delay using timer specific routine.. 5332.22 BogoMIPS (lpj=10664440) [ 55.470698] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 [ 55.470709] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 55.470712] CPU: L2 cache: 512K [ 55.470714] CPU: Physical Processor ID: 0 [ 55.470716] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 [ 55.470724] Intel machine check architecture supported. [ 55.470730] Intel machine check reporting enabled on CPU#1. [ 55.470733] CPU1: Intel P4/Xeon Extended MCE MSRs (12) available [ 55.470736] CPU1: Thermal monitoring enabled [ 55.470907] CPU1: Intel(R) Xeon(TM) CPU 2.66GHz stepping 05 [ 55.471437] Booting processor 2/6 eip 2000 [ 55.471483] CPU 2 irqstacks, hard=c03b1000 soft=c03ad000 [ 55.482063] Initializing CPU#2 [ 55.562668] Calibrating delay using timer specific routine.. 5332.23 BogoMIPS (lpj=10664471) [ 55.562676] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 [ 55.562684] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 55.562687] CPU: L2 cache: 512K [ 55.562688] CPU: Physical Processor ID: 3 [ 55.562690] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 [ 55.562696] Intel machine check architecture supported. [ 55.562701] Intel machine check reporting enabled on CPU#2. [ 55.562703] CPU2: Intel P4/Xeon Extended MCE MSRs (12) available [ 55.562706] CPU2: Thermal monitoring enabled [ 55.562917] CPU2: Intel(R) Xeon(TM) CPU 2.66GHz stepping 05 [ 55.563430] Booting processor 3/7 eip 2000 [ 55.563475] CPU 3 irqstacks, hard=c03b2000 soft=c03ae000 [ 55.573716] Initializing CPU#3 [ 55.654647] Calibrating delay using timer specific routine.. 5332.30 BogoMIPS (lpj=10664613) [ 55.654656] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 [ 55.654667] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 55.654670] CPU: L2 cache: 512K [ 55.654672] CPU: Physical Processor ID: 3 [ 55.654674] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 [ 55.654681] Intel machine check architecture supported. [ 55.654687] Intel machine check reporting enabled on CPU#3. [ 55.654690] CPU3: Intel P4/Xeon Extended MCE MSRs (12) available [ 55.654694] CPU3: Thermal monitoring enabled [ 55.654822] CPU3: Intel(R) Xeon(TM) CPU 2.66GHz stepping 05 [ 55.655331] Total of 4 processors activated (21332.84 BogoMIPS). [ 55.655667] ENABLING IO-APIC IRQs [ 55.655888] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 55.802622] checking TSC synchronization across 4 CPUs: passed. [ 0.011955] Brought up 4 CPUs [ 0.111712] migration_cost=81 [ 0.112311] NET: Registered protocol family 16 [ 0.112440] ACPI: bus type pci registered [ 0.116387] PCI: PCI BIOS revision 2.10 entry at 0xfd8e5, last bus=5 [ 0.116433] PCI: Using configuration type 1 [ 0.116477] Setting up standard PCI resources [ 0.138385] ACPI: Interpreter enabled [ 0.138432] ACPI: Using IOAPIC for interrupt routing [ 0.138963] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.139012] PCI: Probing PCI hardware (bus 00) [ 0.142048] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO [ 0.142097] PCI quirk: region 1180-11bf claimed by ICH4 GPIO [ 0.142190] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 [ 0.142427] Boot video device is 0000:01:00.0 [ 0.143401] PCI: Transparent bridge - 0000:00:1e.0 [ 0.143475] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.148826] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 10 *11 14 15) [ 0.149298] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 10 *11 14 15) [ 0.149762] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 10 11 14 15) *5 [ 0.150259] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *10 11 14 15) [ 0.150729] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 10 *11 14 15) [ 0.151201] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 *11 14 15) [ 0.151672] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 10 11 14 15) *0, disabled. [ 0.152260] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 10 *11 14 15) [ 0.154636] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICH4._PRT] [ 0.155489] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HLB_.P64A._PRT] [ 0.155843] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HLB_.P64B._PRT] [ 0.156625] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] [ 0.156982] SCSI subsystem initialized [ 0.157066] PCI: Using ACPI for IRQ routing [ 0.157111] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 0.208710] PCI: Bridge: 0000:00:01.0 [ 0.208756] IO window: 3000-3fff [ 0.208800] MEM window: d0100000-d01fffff [ 0.208845] PREFETCH window: e8000000-f7ffffff [ 0.208895] PCI: Bridge: 0000:02:1d.0 [ 0.208939] IO window: 4000-4fff [ 0.208985] MEM window: d0300000-d03fffff [ 0.209031] PREFETCH window: 50000000-500fffff [ 0.209079] PCI: Bridge: 0000:02:1f.0 [ 0.209122] IO window: 5000-5fff [ 0.209168] MEM window: d0400000-d04fffff [ 0.209213] PREFETCH window: 50100000-501fffff [ 0.209260] PCI: Bridge: 0000:00:02.0 [ 0.209303] IO window: 4000-5fff [ 0.209347] MEM window: d0200000-d04fffff [ 0.209392] PREFETCH window: 50000000-501fffff [ 0.209438] PCI: Bridge: 0000:00:1e.0 [ 0.209482] IO window: 6000-6fff [ 0.209528] MEM window: d0500000-d05fffff [ 0.209574] PREFETCH window: 50200000-502fffff [ 0.209652] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 0.209693] NET: Registered protocol family 2 [ 0.247969] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.248250] TCP established hash table entries: 131072 (order: 8, 1572864 bytes) [ 0.250005] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 0.251093] TCP: Hash tables configured (established 131072 bind 65536) [ 0.251144] TCP reno registered [ 0.251391] Simple Boot Flag at 0x36 set to 0x1 [ 0.251493] Machine check exception polling timer started. [ 0.251858] highmem bounce pool size: 64 pages [ 0.252182] io scheduler noop registered [ 0.252259] io scheduler deadline registered (default) [ 0.252605] ACPI: Power Button (FF) [PWRF] [ 0.252680] ACPI: Power Button (CM) [PWRB] [ 0.255428] ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 32 (level, low) -> IRQ 16 [ 1.375658] scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 [ 1.375660] <Adaptec AIC7902 Ultra320 SCSI adapter> [ 1.375661] aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs [ 1.375662] [ 1.388245] scsi 0:0:0:0: Direct-Access SEAGATE ST34572W 0876 PQ: 0 ANSI: 2 [ 1.388304] target0:0:0: asynchronous [ 1.388347] scsi0:A:0:0: Tagged Queuing enabled. Depth 32 [ 1.388432] target0:0:0: Beginning Domain Validation [ 1.402919] target0:0:0: wide asynchronous [ 1.413551] target0:0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 1.423495] target0:0:0: Domain Validation skipping write tests [ 1.423541] target0:0:0: Ending Domain Validation [ 1.436046] scsi 0:0:1:0: Direct-Access QUANTUM QM39100TD-SW N491 PQ: 0 ANSI: 2 [ 1.436102] target0:0:1: asynchronous [ 1.436145] scsi0:A:1:0: Tagged Queuing enabled. Depth 32 [ 1.436226] target0:0:1: Beginning Domain Validation [ 1.440886] target0:0:1: wide asynchronous [ 1.444053] target0:0:1: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 31) [ 1.446464] target0:0:1: Domain Validation skipping write tests [ 1.446509] target0:0:1: Ending Domain Validation [ 2.996166] scsi 0:0:9:0: Direct-Access QUANTUM QM39100TD-SW N491 PQ: 0 ANSI: 2 [ 2.996224] target0:0:9: asynchronous [ 2.996267] scsi0:A:9:0: Tagged Queuing enabled. Depth 32 [ 2.996347] target0:0:9: Beginning Domain Validation [ 3.000824] target0:0:9: wide asynchronous [ 3.004197] target0:0:9: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 31) [ 3.006565] target0:0:9: Domain Validation skipping write tests [ 3.006610] target0:0:9: Ending Domain Validation [ 4.550696] ACPI: PCI Interrupt 0000:04:03.1[B] -> GSI 33 (level, low) -> IRQ 17 [ 5.670712] scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 [ 5.670714] <Adaptec AIC7902 Ultra320 SCSI adapter> [ 5.670715] aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs [ 5.670717] [ 11.839403] scsi 1:0:13:0: CD-ROM HL-DT-ST DVDRAM GSA-4160B A300 PQ: 0 ANSI: 2 [ 11.839462] target1:0:13: asynchronous [ 11.839513] target1:0:13: Beginning Domain Validation [ 11.855350] target1:0:13: wide asynchronous [ 11.866981] target1:0:13: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 14) [ 11.878231] target1:0:13: Domain Validation skipping write tests [ 11.878277] target1:0:13: Ending Domain Validation [ 12.404878] SCSI device sda: 8888924 512-byte hdwr sectors (4551 MB) [ 12.408854] sda: Write Protect is off [ 12.408898] sda: Mode Sense: 9f 00 10 08 [ 12.413080] SCSI device sda: drive cache: write back w/ FUA [ 12.415659] SCSI device sda: 8888924 512-byte hdwr sectors (4551 MB) [ 12.419610] sda: Write Protect is off [ 12.419653] sda: Mode Sense: 9f 00 10 08 [ 12.423836] SCSI device sda: drive cache: write back w/ FUA [ 12.423881] sda: sda1 sda2 [ 12.440659] sd 0:0:0:0: Attached scsi disk sda [ 12.443705] SCSI device sdb: 17783250 512-byte hdwr sectors (9105 MB) [ 12.445824] sdb: Write Protect is off [ 12.445867] sdb: Mode Sense: e1 00 10 08 [ 12.447628] SCSI device sdb: drive cache: write back w/ FUA [ 12.448400] SCSI device sdb: 17783250 512-byte hdwr sectors (9105 MB) [ 12.450768] sdb: Write Protect is off [ 12.450812] sdb: Mode Sense: e1 00 10 08 [ 12.452574] SCSI device sdb: drive cache: write back w/ FUA [ 12.452619] sdb: unknown partition table [ 12.453154] sd 0:0:1:0: Attached scsi disk sdb [ 12.456197] SCSI device sdc: 17783250 512-byte hdwr sectors (9105 MB) [ 12.458370] sdc: Write Protect is off [ 12.458413] sdc: Mode Sense: e1 00 10 08 [ 12.460217] SCSI device sdc: drive cache: write back w/ FUA [ 12.460980] SCSI device sdc: 17783250 512-byte hdwr sectors (9105 MB) [ 12.463098] sdc: Write Protect is off [ 12.463141] sdc: Mode Sense: e1 00 10 08 [ 12.464899] SCSI device sdc: drive cache: write back w/ FUA [ 12.464944] sdc: unknown partition table [ 12.465467] sd 0:0:9:0: Attached scsi disk sdc [ 12.467860] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 12.467908] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 12.468036] mice: PS/2 mouse device common for all mice [ 12.468223] input: PC Speaker as /class/input/input0 [ 12.488053] input: AT Translated Set 2 keyboard as /class/input/input1 [ 12.653197] TCP cubic registered [ 12.653248] NET: Registered protocol family 1 [ 12.653350] Starting balanced_irq [ 12.653408] Using IPI Shortcut mode [ 12.657074] Time: tsc clocksource has been installed. [ 12.759066] EXT3-fs: INFO: recovery required on readonly filesystem. [ 12.759114] EXT3-fs: write access will be enabled during recovery. [ 13.300716] kjournald starting. Commit interval 5 seconds [ 13.300732] EXT3-fs: recovery complete. [ 13.322667] EXT3-fs: mounted filesystem with ordered data mode. [ 13.322769] VFS: Mounted root (ext3 filesystem) readonly. [ 13.323025] Freeing unused kernel memory: 208k freed [ 18.236341] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 48 (level, low) -> IRQ 18 [ 19.447683] scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 [ 19.447686] <Adaptec 3960D Ultra160 SCSI adapter> [ 19.447688] aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs [ 19.447689] [ 21.687533] scsi 2:0:0:0: Direct-Access SEAGATE SX150176LC BA12 PQ: 0 ANSI: 2 [ 21.687601] scsi2:A:0:0: Tagged Queuing enabled. Depth 32 [ 21.687690] target2:0:0: Beginning Domain Validation [ 21.692983] target2:0:0: wide asynchronous [ 21.696996] target2:0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 21.700265] target2:0:0: Domain Validation skipping write tests [ 21.700311] target2:0:0: Ending Domain Validation [ 21.707201] SCSI device sdd: 97693755 512-byte hdwr sectors (50019 MB) [ 21.709832] sdd: Write Protect is off [ 21.709889] sdd: Mode Sense: cb 00 10 08 [ 21.712379] SCSI device sdd: drive cache: write through w/ FUA [ 21.713240] SCSI device sdd: 97693755 512-byte hdwr sectors (50019 MB) [ 21.715834] sdd: Write Protect is off [ 21.715880] sdd: Mode Sense: cb 00 10 08 [ 21.718353] SCSI device sdd: drive cache: write through w/ FUA [ 21.718401] sdd: unknown partition table [ 21.742790] sd 2:0:0:0: Attached scsi disk sdd [ 21.752477] scsi 2:0:1:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 21.752548] scsi2:A:1:0: Tagged Queuing enabled. Depth 32 [ 21.752653] target2:0:1: Beginning Domain Validation [ 21.762443] target2:0:1: wide asynchronous [ 21.767231] target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 21.771093] target2:0:1: Domain Validation skipping write tests [ 21.771143] target2:0:1: Ending Domain Validation [ 21.775329] SCSI device sde: 97693755 512-byte hdwr sectors (50019 MB) [ 21.777516] sde: Write Protect is off [ 21.777564] sde: Mode Sense: cb 00 10 08 [ 21.780113] SCSI device sde: drive cache: write through w/ FUA [ 21.781010] SCSI device sde: 97693755 512-byte hdwr sectors (50019 MB) [ 21.783747] sde: Write Protect is off [ 21.783809] sde: Mode Sense: cb 00 10 08 [ 21.786377] SCSI device sde: drive cache: write through w/ FUA [ 21.786428] sde: unknown partition table [ 21.805915] sd 2:0:1:0: Attached scsi disk sde [ 21.817669] scsi 2:0:2:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 21.817758] scsi2:A:2:0: Tagged Queuing enabled. Depth 32 [ 21.817857] target2:0:2: Beginning Domain Validation [ 21.823531] target2:0:2: wide asynchronous [ 21.829319] target2:0:2: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 21.832716] target2:0:2: Domain Validation skipping write tests [ 21.832768] target2:0:2: Ending Domain Validation [ 21.838742] SCSI device sdf: 97693755 512-byte hdwr sectors (50019 MB) [ 21.844503] sdf: Write Protect is off [ 21.844562] sdf: Mode Sense: cb 00 10 08 [ 21.848184] SCSI device sdf: drive cache: write through w/ FUA [ 21.849129] SCSI device sdf: 97693755 512-byte hdwr sectors (50019 MB) [ 21.851754] sdf: Write Protect is off [ 21.851798] sdf: Mode Sense: cb 00 10 08 [ 21.854339] SCSI device sdf: drive cache: write through w/ FUA [ 21.854388] sdf: unknown partition table [ 21.871229] sd 2:0:2:0: Attached scsi disk sdf [ 21.883201] scsi 2:0:3:0: Direct-Access SEAGATE SX150176LC BA12 PQ: 0 ANSI: 2 [ 21.883286] scsi2:A:3:0: Tagged Queuing enabled. Depth 32 [ 21.883401] target2:0:3: Beginning Domain Validation [ 21.888902] target2:0:3: wide asynchronous [ 21.893187] target2:0:3: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 21.896573] target2:0:3: Domain Validation skipping write tests [ 21.896623] target2:0:3: Ending Domain Validation [ 21.907010] SCSI device sdg: 97693755 512-byte hdwr sectors (50019 MB) [ 21.909659] sdg: Write Protect is off [ 21.909716] sdg: Mode Sense: cb 00 10 08 [ 21.912238] SCSI device sdg: drive cache: write through w/ FUA [ 21.913085] SCSI device sdg: 97693755 512-byte hdwr sectors (50019 MB) [ 21.915738] sdg: Write Protect is off [ 21.915827] sdg: Mode Sense: cb 00 10 08 [ 21.918391] SCSI device sdg: drive cache: write through w/ FUA [ 21.918444] sdg: unknown partition table [ 21.936874] sd 2:0:3:0: Attached scsi disk sdg [ 21.942181] scsi 2:0:4:0: Direct-Access SEAGATE SX150176LC BA12 PQ: 0 ANSI: 2 [ 21.942279] scsi2:A:4:0: Tagged Queuing enabled. Depth 32 [ 21.942398] target2:0:4: Beginning Domain Validation [ 21.948010] target2:0:4: wide asynchronous [ 21.952283] target2:0:4: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 21.955659] target2:0:4: Domain Validation skipping write tests [ 21.955724] target2:0:4: Ending Domain Validation [ 21.961746] SCSI device sdh: 97693755 512-byte hdwr sectors (50019 MB) [ 21.964417] sdh: Write Protect is off [ 21.964490] sdh: Mode Sense: cb 00 10 08 [ 21.967099] SCSI device sdh: drive cache: write through w/ FUA [ 21.968045] SCSI device sdh: 97693755 512-byte hdwr sectors (50019 MB) [ 21.970696] sdh: Write Protect is off [ 21.970765] sdh: Mode Sense: cb 00 10 08 [ 21.973339] SCSI device sdh: drive cache: write through w/ FUA [ 21.973412] sdh: unknown partition table [ 21.991326] sd 2:0:4:0: Attached scsi disk sdh [ 24.078966] scsi 2:0:14:0: Processor SYMBIOS SYM2000 2 PQ: 0 ANSI: 2 [ 24.079058] target2:0:14: Beginning Domain Validation [ 24.079519] target2:0:14: Ending Domain Validation [ 24.354730] ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 49 (level, low) -> IRQ 19 [ 25.566346] scsi3 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 [ 25.566349] <Adaptec 3960D Ultra160 SCSI adapter> [ 25.566350] aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs [ 25.566352] [ 27.781555] scsi 3:0:0:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 27.781623] scsi3:A:0:0: Tagged Queuing enabled. Depth 32 [ 27.781711] target3:0:0: Beginning Domain Validation [ 27.787035] target3:0:0: wide asynchronous [ 27.791300] target3:0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 27.794607] target3:0:0: Domain Validation skipping write tests [ 27.794653] target3:0:0: Ending Domain Validation [ 27.804053] SCSI device sdi: 97693755 512-byte hdwr sectors (50019 MB) [ 27.806283] sdi: Write Protect is off [ 27.806344] sdi: Mode Sense: cb 00 10 08 [ 27.808916] SCSI device sdi: drive cache: write through w/ FUA [ 27.809872] SCSI device sdi: 97693755 512-byte hdwr sectors (50019 MB) [ 27.816625] sdi: Write Protect is off [ 27.816689] sdi: Mode Sense: cb 00 10 08 [ 27.819272] SCSI device sdi: drive cache: write through w/ FUA [ 27.819325] sdi: unknown partition table [ 27.841870] sd 3:0:0:0: Attached scsi disk sdi [ 27.852720] scsi 3:0:1:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 27.852809] scsi3:A:1:0: Tagged Queuing enabled. Depth 32 [ 27.852916] target3:0:1: Beginning Domain Validation [ 27.866711] target3:0:1: wide asynchronous [ 27.871821] target3:0:1: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 27.875135] target3:0:1: Domain Validation skipping write tests [ 27.875181] target3:0:1: Ending Domain Validation [ 27.890022] SCSI device sdj: 97693755 512-byte hdwr sectors (50019 MB) [ 27.892268] sdj: Write Protect is off [ 27.892323] sdj: Mode Sense: cb 00 10 08 [ 27.895199] SCSI device sdj: drive cache: write through w/ FUA [ 27.896112] SCSI device sdj: 97693755 512-byte hdwr sectors (50019 MB) [ 27.898787] sdj: Write Protect is off [ 27.898850] sdj: Mode Sense: cb 00 10 08 [ 27.901454] SCSI device sdj: drive cache: write through w/ FUA [ 27.901506] sdj: unknown partition table [ 27.921451] sd 3:0:1:0: Attached scsi disk sdj [ 27.931099] scsi 3:0:2:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 27.931193] scsi3:A:2:0: Tagged Queuing enabled. Depth 32 [ 27.931326] target3:0:2: Beginning Domain Validation [ 27.937886] target3:0:2: wide asynchronous [ 27.942743] target3:0:2: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 27.946112] target3:0:2: Domain Validation skipping write tests [ 27.946165] target3:0:2: Ending Domain Validation [ 27.954710] SCSI device sdk: 97693755 512-byte hdwr sectors (50019 MB) [ 27.956961] sdk: Write Protect is off [ 27.957016] sdk: Mode Sense: cb 00 10 08 [ 27.959621] SCSI device sdk: drive cache: write through w/ FUA [ 27.960671] SCSI device sdk: 97693755 512-byte hdwr sectors (50019 MB) [ 27.963366] sdk: Write Protect is off [ 27.963421] sdk: Mode Sense: cb 00 10 08 [ 27.965999] SCSI device sdk: drive cache: write through w/ FUA [ 27.966055] sdk: unknown partition table [ 27.989870] sd 3:0:2:0: Attached scsi disk sdk [ 27.998923] scsi 3:0:3:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 27.999020] scsi3:A:3:0: Tagged Queuing enabled. Depth 32 [ 27.999141] target3:0:3: Beginning Domain Validation [ 28.008953] target3:0:3: wide asynchronous [ 28.013204] target3:0:3: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 28.016557] target3:0:3: Domain Validation skipping write tests [ 28.016608] target3:0:3: Ending Domain Validation [ 28.019765] SCSI device sdl: 97693755 512-byte hdwr sectors (50019 MB) [ 28.021960] sdl: Write Protect is off [ 28.022020] sdl: Mode Sense: cb 00 10 08 [ 28.027129] SCSI device sdl: drive cache: write through w/ FUA [ 28.028045] SCSI device sdl: 97693755 512-byte hdwr sectors (50019 MB) [ 28.030768] sdl: Write Protect is off [ 28.030832] sdl: Mode Sense: cb 00 10 08 [ 28.033415] SCSI device sdl: drive cache: write through w/ FUA [ 28.033475] sdl: unknown partition table [ 28.049196] sd 3:0:3:0: Attached scsi disk sdl [ 28.054520] scsi 3:0:4:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 28.054619] scsi3:A:4:0: Tagged Queuing enabled. Depth 32 [ 28.054740] target3:0:4: Beginning Domain Validation [ 28.060309] target3:0:4: wide asynchronous [ 28.064449] target3:0:4: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15) [ 28.067829] target3:0:4: Domain Validation skipping write tests [ 28.067881] target3:0:4: Ending Domain Validation [ 28.072728] SCSI device sdm: 97693755 512-byte hdwr sectors (50019 MB) [ 28.074966] sdm: Write Protect is off [ 28.075031] sdm: Mode Sense: cb 00 10 08 [ 28.077684] SCSI device sdm: drive cache: write through w/ FUA [ 28.078732] SCSI device sdm: 97693755 512-byte hdwr sectors (50019 MB) [ 28.081455] sdm: Write Protect is off [ 28.081523] sdm: Mode Sense: cb 00 10 08 [ 28.084151] SCSI device sdm: drive cache: write through w/ FUA [ 28.084213] sdm: unknown partition table [ 28.100025] sd 3:0:4:0: Attached scsi disk sdm [ 30.158852] scsi 3:0:14:0: Processor SYMBIOS SYM2000 2 PQ: 0 ANSI: 2 [ 30.158933] target3:0:14: Beginning Domain Validation [ 30.159346] target3:0:14: Ending Domain Validation [ 30.450736] ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 16 (level, low) -> IRQ 20 [ 31.461045] scsi4 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 [ 31.461048] <Adaptec 2940/DUAL Ultra SCSI adapter> [ 31.461050] aic7895: Ultra Wide Channel A, SCSI Id=7, 32/253 SCBs [ 31.461051] [ 32.009752] scsi 4:0:2:0: CD-ROM PLEXTOR CD-ROM PX-40TS 1.11 PQ: 0 ANSI: 2 [ 32.009882] target4:0:2: Beginning Domain Validation [ 32.014686] target4:0:2: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15) [ 32.017640] target4:0:2: Domain Validation skipping write tests [ 32.017695] target4:0:2: Ending Domain Validation [ 32.040376] scsi 4:0:3:0: CD-ROM PLEXTOR CD-R PX-W4012S 1.01 PQ: 0 ANSI: 2 [ 32.040472] target4:0:3: Beginning Domain Validation [ 32.042879] target4:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15) [ 32.044431] target4:0:3: Domain Validation skipping write tests [ 32.044490] target4:0:3: Ending Domain Validation [ 32.062090] scsi 4:0:4:0: CD-ROM NAKAMICH MJ-5.16S 1.07 PQ: 0 ANSI: 2 [ 32.062204] target4:0:4: Beginning Domain Validation [ 32.067703] target4:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) [ 32.070777] target4:0:4: Domain Validation skipping write tests [ 32.070829] target4:0:4: Ending Domain Validation [ 32.080961] scsi 4:0:4:1: CD-ROM NAKAMICH MJ-5.16S 1.07 PQ: 0 ANSI: 2 [ 32.081055] target4:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) [ 32.094088] scsi 4:0:4:2: CD-ROM NAKAMICH MJ-5.16S 1.07 PQ: 0 ANSI: 2 [ 32.094181] target4:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) [ 32.106980] scsi 4:0:4:3: CD-ROM NAKAMICH MJ-5.16S 1.07 PQ: 0 ANSI: 2 [ 32.107102] target4:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) [ 32.118312] scsi 4:0:4:4: CD-ROM NAKAMICH MJ-5.16S 1.07 PQ: 0 ANSI: 2 [ 32.118423] target4:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) [ 32.139326] scsi 4:0:5:0: CD-ROM YAMAHA CRW8424S 1.0d PQ: 0 ANSI: 2 [ 32.139474] target4:0:5: Beginning Domain Validation [ 32.155331] target4:0:5: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15) [ 32.165552] target4:0:5: Domain Validation skipping write tests [ 32.165619] target4:0:5: Ending Domain Validation [ 34.542463] ACPI: PCI Interrupt 0000:05:01.1[B] -> GSI 17 (level, low) -> IRQ 21 [ 35.552159] scsi5 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 [ 35.552162] <Adaptec 2940/DUAL Ultra SCSI adapter> [ 35.552164] aic7895: Ultra Single Channel B, SCSI Id=7, 32/253 SCBs [ 35.552165] [ 50.252880] EXT3 FS on sda1, internal journal [ 53.188367] Intel(R) PRO/1000 Network Driver - version 7.2.9-k4 [ 53.188445] Copyright (c) 1999-2006 Intel Corporation. [ 53.192470] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 54 (level, low) -> IRQ 22 [ 53.466611] e1000: 0000:03:03.0: e1000_probe: (PCI:66MHz:64-bit) 00:30:48:73:b9:cb [ 53.501760] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection [ 53.598803] netconsole: local port 4321 [ 53.598866] netconsole: local IP 192.168.2.7 [ 53.598914] netconsole: interface eth0 [ 53.598960] netconsole: remote port 1234 [ 53.599006] netconsole: remote IP 192.168.2.15 [ 53.599056] netconsole: remote ethernet address 00:10:5a:21:9b:be [ 53.599109] netconsole: device eth0 not up yet, forcing it [ 56.591864] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex [ 56.626868] netconsole: network logging started [ 56.681017] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 21 [ 57.359779] md: raid1 personality registered for level 1 [ 57.417471] raid5: automatically using best checksumming function: pIII_sse [ 57.434914] pIII_sse : 3305.000 MB/sec [ 57.434984] raid5: using function: pIII_sse (3305.000 MB/sec) [ 57.546953] raid6: int32x1 618 MB/s [ 57.614927] raid6: int32x2 719 MB/s [ 57.682892] raid6: int32x4 668 MB/s [ 57.750965] raid6: int32x8 473 MB/s [ 57.818833] raid6: mmxx1 2047 MB/s [ 57.886818] raid6: mmxx2 2630 MB/s [ 57.954817] raid6: sse1x1 1136 MB/s [ 58.022806] raid6: sse1x2 1062 MB/s [ 58.090768] raid6: sse2x1 2041 MB/s [ 58.158748] raid6: sse2x2 2911 MB/s [ 58.158793] raid6: using algorithm sse2x2 (2911 MB/s) [ 58.158842] md: raid6 personality registered for level 6 [ 58.158888] md: raid5 personality registered for level 5 [ 58.158934] md: raid4 personality registered for level 4 [ 59.173609] device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@xxxxxxxxxx [ 61.357392] md: bind<sdd> [ 61.373439] md: bind<sde> [ 61.387336] md: bind<sdf> [ 61.402219] md: bind<sdg> [ 61.407919] md: bind<sdh> [ 61.423371] md: bind<sdi> [ 61.441688] md: bind<sdj> [ 61.461825] md: bind<sdk> [ 61.465305] md: bind<sdl> [ 61.482296] md: bind<sdm> [ 61.492627] raid5: device sdm operational as raid disk 9 [ 61.492684] raid5: device sdl operational as raid disk 8 [ 61.492730] raid5: device sdk operational as raid disk 7 [ 61.492776] raid5: device sdj operational as raid disk 6 [ 61.492822] raid5: device sdi operational as raid disk 5 [ 61.492878] raid5: device sdh operational as raid disk 4 [ 61.492924] raid5: device sdg operational as raid disk 3 [ 61.492973] raid5: device sdf operational as raid disk 2 [ 61.493019] raid5: device sde operational as raid disk 1 [ 61.493064] raid5: device sdd operational as raid disk 0 [ 61.493919] raid5: allocated 10438kB for md0 [ 61.493970] raid5: raid level 5 set md0 active with 10 out of 10 devices, algorithm 0 [ 61.494024] RAID5 conf printout: [ 61.494067] --- rd:10 wd:10 [ 61.494115] disk 0, o:1, dev:sdd [ 61.494159] disk 1, o:1, dev:sde [ 61.494202] disk 2, o:1, dev:sdf [ 61.494248] disk 3, o:1, dev:sdg [ 61.494291] disk 4, o:1, dev:sdh [ 61.494338] disk 5, o:1, dev:sdi [ 61.494381] disk 6, o:1, dev:sdj [ 61.494437] disk 7, o:1, dev:sdk [ 61.494484] disk 8, o:1, dev:sdl [ 61.494528] disk 9, o:1, dev:sdm [ 61.638169] md: bind<sdb> [ 61.650445] md: bind<sdc> [ 61.668979] raid1: raid set md1 active with 2 out of 2 mirrors [ 86.733733] ReiserFS: dm-5: found reiserfs format "3.6" with standard journal [ 86.733801] ReiserFS: dm-5: using ordered data mode [ 86.739097] ReiserFS: dm-5: journal params: device dm-5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 86.740289] ReiserFS: dm-5: checking transaction log (dm-5) [ 86.864654] ReiserFS: dm-5: Using r5 hash to sort names [ 86.917196] ReiserFS: dm-6: found reiserfs format "3.6" with standard journal [ 86.917264] ReiserFS: dm-6: using ordered data mode [ 86.922419] ReiserFS: dm-6: journal params: device dm-6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 86.923635] ReiserFS: dm-6: checking transaction log (dm-6) [ 86.989879] ReiserFS: dm-6: Using r5 hash to sort names [ 87.026297] ReiserFS: dm-3: found reiserfs format "3.6" with standard journal [ 87.026366] ReiserFS: dm-3: using ordered data mode [ 87.031477] ReiserFS: dm-3: journal params: device dm-3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 87.032729] ReiserFS: dm-3: checking transaction log (dm-3) [ 87.072320] ReiserFS: dm-3: Using r5 hash to sort names [ 87.130105] ReiserFS: sda2: found reiserfs format "3.6" with standard journal [ 87.130177] ReiserFS: sda2: using ordered data mode [ 87.140192] ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 87.141394] ReiserFS: sda2: checking transaction log (sda2) [ 87.217624] ReiserFS: sda2: Using r5 hash to sort names [ 87.338255] ReiserFS: md1: found reiserfs format "3.6" with standard journal [ 87.338326] ReiserFS: md1: using ordered data mode [ 87.345881] ReiserFS: md1: journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 87.347063] ReiserFS: md1: checking transaction log (md1) [ 87.437662] ReiserFS: md1: Using r5 hash to sort names [ 87.498509] ReiserFS: dm-4: found reiserfs format "3.6" with standard journal [ 87.498585] ReiserFS: dm-4: using ordered data mode [ 87.506235] ReiserFS: dm-4: journal params: device dm-4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 87.507448] ReiserFS: dm-4: checking transaction log (dm-4) [ 87.635480] ReiserFS: dm-4: Using r5 hash to sort names [ 87.712688] ReiserFS: dm-0: warning: read_super_block: found reiserfs format "3.6" with non-standard journal [ 87.712783] ReiserFS: dm-0: using ordered data mode [ 87.722188] ReiserFS: dm-0: journal params: device dm-0, size 1023, journal first block 18, max trans len 511, max batch 449, max commit age 30, max trans age 30 [ 87.722415] ReiserFS: dm-0: checking transaction log (dm-0) [ 87.753145] ReiserFS: dm-0: Using r5 hash to sort names [ 87.800729] kjournald starting. Commit interval 5 seconds [ 87.821032] EXT3 FS on dm-1, internal journal [ 87.821128] EXT3-fs: mounted filesystem with ordered data mode. [ 87.821625] ReiserFS: dm-2: found reiserfs format "3.6" with standard journal [ 87.821699] ReiserFS: dm-2: using ordered data mode [ 87.821878] ReiserFS: dm-2: journal params: device dm-2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 87.823111] ReiserFS: dm-2: checking transaction log (dm-2) [ 87.865241] ReiserFS: dm-2: Using r5 hash to sort names [ 88.296742] ip_tables: (C) 2000-2006 Netfilter Core Team [ 88.608163] ip_conntrack version 2.4 (8187 buckets, 65496 max) - 212 bytes per conntrack [ 91.812047] Linux agpgart interface v0.101 (c) Dave Jones [ 91.835035] agpgart: Detected an Intel E7505 Chipset. [ 91.849782] agpgart: AGP aperture is 128M @ 0xd8000000 [ 92.569925] usbcore: registered new interface driver usbfs [ 92.571634] usbcore: registered new interface driver hub [ 92.583991] usbcore: registered new device driver usb [ 92.611747] USB Universal Host Controller Interface driver v3.0 [ 92.626303] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 20 [ 92.626438] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 92.626445] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 92.626952] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 92.627067] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00002440 [ 92.646968] usb usb1: configuration #1 chosen from 1 choice [ 92.664368] hub 1-0:1.0: USB hub found [ 92.664467] hub 1-0:1.0: 2 ports detected [ 92.780087] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 23 [ 92.780965] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 92.780978] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 92.781372] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 92.781524] uhci_hcd 0000:00:1d.1: irq 23, io base 0x00002460 [ 92.807622] usb usb2: configuration #1 chosen from 1 choice [ 92.845292] hub 2-0:1.0: USB hub found [ 92.852374] hub 2-0:1.0: 2 ports detected [ 92.971624] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 24 [ 92.971750] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 92.971757] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 92.996425] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 92.996540] uhci_hcd 0000:00:1d.2: irq 24, io base 0x00002480 [ 93.039622] usb usb3: configuration #1 chosen from 1 choice [ 93.082249] hub 3-0:1.0: USB hub found [ 93.082351] hub 3-0:1.0: 2 ports detected [ 93.211473] usb 2-1: new full speed USB device using uhci_hcd and address 2 [ 93.387512] usb 2-1: configuration #1 chosen from 1 choice [ 93.393563] hub 2-1:1.0: USB hub found [ 93.395391] hub 2-1:1.0: 3 ports detected [ 93.747344] usb 3-1: new full speed USB device using uhci_hcd and address 2 [ 93.920565] usb 3-1: configuration #1 chosen from 1 choice [ 93.927450] hub 3-1:1.0: USB hub found [ 93.930254] hub 3-1:1.0: 4 ports detected [ 94.244996] usb 2-1.1: new full speed USB device using uhci_hcd and address 3 [ 94.385306] usb 2-1.1: configuration #1 chosen from 1 choice [ 94.636817] usb 2-1.3: new low speed USB device using uhci_hcd and address 4 [ 94.774151] usb 2-1.3: configuration #1 chosen from 1 choice [ 97.878771] usbcore: registered new interface driver hiddev [ 97.897740] input: Dell Dell USB Keyboard as /class/input/input2 [ 97.897876] input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.1-1.1 [ 97.921761] input: Dell Dell USB Keyboard as /class/input/input3 [ 97.921874] input: USB HID v1.10 Device [Dell Dell USB Keyboard] on usb-0000:00:1d.1-1.1 [ 97.934827] input: Logitech USB-PS/2 Optical Mouse as /class/input/input4 [ 97.935057] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-1.3 [ 97.935223] usbcore: registered new interface driver usbhid [ 97.935288] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 99.026249] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 25 [ 99.026415] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 99.026422] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 99.026765] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 [ 99.026927] ehci_hcd 0000:00:1d.7: debug port 1 [ 99.027003] PCI: cache line size of 128 is not supported by device 0000:00:1d.7 [ 99.027021] ehci_hcd 0000:00:1d.7: irq 25, io mem 0xd0000000 [ 99.030963] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 99.044762] usb usb4: configuration #1 chosen from 1 choice [ 99.046373] hub 4-0:1.0: USB hub found [ 99.046478] hub 4-0:1.0: 6 ports detected [ 99.586052] usb 4-5: new high speed USB device using ehci_hcd and address 3 [ 99.720108] usb 4-5: configuration #1 chosen from 1 choice [ 99.720634] hub 4-5:1.0: USB hub found [ 99.721074] hub 4-5:1.0: 4 ports detected [ 99.830222] usb 3-1: USB disconnect, address 2 [ 99.974030] usb 2-1: USB disconnect, address 2 [ 99.974123] usb 2-1.1: USB disconnect, address 3 [ 100.012259] usb 2-1.3: USB disconnect, address 4 [ 100.325914] usb 2-1: new full speed USB device using uhci_hcd and address 5 [ 100.511410] usb 2-1: configuration #1 chosen from 1 choice [ 100.517411] hub 2-1:1.0: USB hub found [ 100.519192] hub 2-1:1.0: 3 ports detected [ 100.831023] usb 2-1.1: new full speed USB device using uhci_hcd and address 6 [ 100.967424] usb 2-1.1: configuration #1 chosen from 1 choice [ 100.992955] input: Dell Dell USB Keyboard as /class/input/input5 [ 100.993059] input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.1-1.1 [ 101.021903] input: Dell Dell USB Keyboard as /class/input/input6 [ 101.022035] input: USB HID v1.10 Device [Dell Dell USB Keyboard] on usb-0000:00:1d.1-1.1 [ 101.250845] usb 2-1.3: new low speed USB device using uhci_hcd and address 7 [ 101.400074] usb 2-1.3: configuration #1 chosen from 1 choice [ 101.416128] input: Logitech USB-PS/2 Optical Mouse as /class/input/input7 [ 101.416404] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-1.3 [ 103.502556] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 103.502644] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 103.547432] ICH4: IDE controller at PCI slot 0000:00:1f.1 [ 103.547530] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 24 [ 103.547658] ICH4: chipset revision 2 [ 103.547715] ICH4: not 100% native mode: will probe irqs later [ 103.547789] ide0: BM-DMA at 0x24a0-0x24a7, BIOS settings: hda:DMA, hdb:pio [ 103.547979] ide1: BM-DMA at 0x24a8-0x24af, BIOS settings: hdc:pio, hdd:pio [ 103.548131] Probing IDE interface ide0... [ 104.569105] hda: ATAPI CDROM, ATAPI CD/DVD-ROM drive [ 104.905096] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 104.905358] Probing IDE interface ide1... [ 106.117242] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 21 [ 106.117373] PCI: Setting latency timer of device 0000:00:1f.5 to 64 [ 106.432539] intel8x0_measure_ac97_clock: measured 52769 usecs [ 106.432595] intel8x0: clocking to 48000 [ 115.215184] ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device [ 115.215310] scsi6 : SCSI host adapter emulation for IDE ATAPI devices [ 115.215964] scsi 6:0:0:0: CD-ROM ATAPI CDROM. 100A PQ: 0 ANSI: 0 CCS [ 115.380052] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray [ 115.380152] Uniform CD-ROM driver Revision: 3.20 [ 115.380718] sr 1:0:13:0: Attached scsi CD-ROM sr0 [ 115.386182] sr1: scsi-1 drive [ 115.390675] sr 4:0:2:0: Attached scsi CD-ROM sr1 [ 115.393588] sr2: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray [ 115.394624] sr 4:0:3:0: Attached scsi CD-ROM sr2 [ 115.399817] sr3: scsi3-mmc drive: 16x/16x xa/form2 cdda changer [ 115.426129] sr 4:0:4:0: Attached scsi CD-ROM sr3 [ 115.436188] sr4: scsi3-mmc drive: 16x/16x xa/form2 cdda changer [ 115.454056] sr 4:0:4:1: Attached scsi CD-ROM sr4 [ 115.459314] sr5: scsi3-mmc drive: 16x/16x xa/form2 cdda changer [ 115.478654] sr 4:0:4:2: Attached scsi CD-ROM sr5 [ 115.484218] sr6: scsi3-mmc drive: 16x/16x xa/form2 cdda changer [ 115.506702] sr 4:0:4:3: Attached scsi CD-ROM sr6 [ 115.511989] sr7: scsi3-mmc drive: 16x/16x xa/form2 cdda changer [ 115.528195] sr 4:0:4:4: Attached scsi CD-ROM sr7 [ 115.551908] sr8: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray [ 115.568819] sr 4:0:5:0: Attached scsi CD-ROM sr8 [ 115.570326] sr9: scsi-1 drive [ 115.597729] sr 6:0:0:0: Attached scsi CD-ROM sr9 [ 115.744116] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 115.754534] sd 0:0:1:0: Attached scsi generic sg1 type 0 [ 115.762560] sd 0:0:9:0: Attached scsi generic sg2 type 0 [ 115.795865] sr 1:0:13:0: Attached scsi generic sg3 type 5 [ 115.808705] sd 2:0:0:0: Attached scsi generic sg4 type 0 [ 115.812880] sd 2:0:1:0: Attached scsi generic sg5 type 0 [ 115.826400] sd 2:0:2:0: Attached scsi generic sg6 type 0 [ 115.843572] sd 2:0:3:0: Attached scsi generic sg7 type 0 [ 115.858501] sd 2:0:4:0: Attached scsi generic sg8 type 0 [ 115.861462] scsi 2:0:14:0: Attached scsi generic sg9 type 3 [ 115.863652] sd 3:0:0:0: Attached scsi generic sg10 type 0 [ 115.875876] sd 3:0:1:0: Attached scsi generic sg11 type 0 [ 115.884915] sd 3:0:2:0: Attached scsi generic sg12 type 0 [ 115.891015] sd 3:0:3:0: Attached scsi generic sg13 type 0 [ 115.919991] sd 3:0:4:0: Attached scsi generic sg14 type 0 [ 115.933426] scsi 3:0:14:0: Attached scsi generic sg15 type 3 [ 115.950479] sr 4:0:2:0: Attached scsi generic sg16 type 5 [ 115.952236] sr 4:0:3:0: Attached scsi generic sg17 type 5 [ 115.987777] sr 4:0:4:0: Attached scsi generic sg18 type 5 [ 116.004495] sr 4:0:4:1: Attached scsi generic sg19 type 5 [ 116.005215] sr 4:0:4:2: Attached scsi generic sg20 type 5 [ 116.024151] sr 4:0:4:3: Attached scsi generic sg21 type 5 [ 116.034343] sr 4:0:4:4: Attached scsi generic sg22 type 5 [ 116.078676] sr 4:0:5:0: Attached scsi generic sg23 type 5 [ 116.102233] sr 6:0:0:0: Attached scsi generic sg24 type 5 [ 122.126324] tun: Universal TUN/TAP device driver, 1.6 [ 122.126406] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx> [ 123.088556] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx). [ 130.247037] [drm] Initialized drm 1.0.1 20051102 [ 130.284254] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 21 (level, low) -> IRQ 26 [ 130.284924] [drm] Initialized radeon 1.25.0 20060524 on minor 0 [ 131.670528] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. [ 131.670555] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode [ 131.670593] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode [ 131.979309] [drm] Setting GART location based on new memory map [ 131.979328] [drm] Loading R200 Microcode [ 131.979372] [drm] writeback test succeeded in 1 usecs -- Lab tests show that use of micro$oft causes cancer in lab animals Got Gas??? - To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
