On Tue, Sep 05, James Bottomley wrote: > On Tue, 2006-09-05 at 14:26 +0200, Olaf Hering wrote: > > <4>Machine check in kernel mode. > > <4>Caused by (from SRR1=49030): Transfer error ack signal > > <4>Oops: Machine check, sig: 7 [#1] > [...] > > <4> scsi0: PCI error Interrupt at seqaddr = 0x8 > > Is this actually a PCI bus error? In which case it's probably the > ahc_inb(,SBLKCTL) of ahc_linux_get_signalling(). Can you verify this? > And what happens when you try to cat /proc/scsi_host/host<n>/signalling > for this card? This causes another machine check because it runs ahc_inb(ahc, SBLKCTL) again. With debug I get: CONFIG_SCSI_AIC7XXX=m CONFIG_AIC7XXX_CMDS_PER_DEVICE=32 CONFIG_AIC7XXX_RESET_DELAY_MS=5000 CONFIG_AIC7XXX_DEBUG_ENABLE=y CONFIG_AIC7XXX_DEBUG_MASK=2047 CONFIG_AIC7XXX_REG_PRETTY_PRINT=y <4>ahc_pci:1:4:0: hardware scb 64 bytes; kernel scb 52 bytes; ahc_dma 8 bytes <6>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 <4> <Adaptec 2940B Ultra2 SCSI adapter> <4> aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs <4> <5> Vendor: IBM Model: DDRS-39130D Rev: DC2A <5> Type: Direct-Access ANSI SCSI revision: 02 <4>scsi0:A:0:0: Tagged Queuing enabled. Depth 32 <6> target0:0:0: Beginning Domain Validation <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0xc0 <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x20 <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x3 <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x1 <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x2 <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x3 <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x1 <4>scsi0:A:0:0: INITIATOR_MSG_OUT PHASEMIS in Message-in phase <4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x1 <4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x2 <4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x3 <4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x1 <4>scsi0:A:0:0: Asserting ATN for response <4>scsi0:A:0:0: INITIATOR_MSG_IN PHASEMIS in Message-out phase <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x1 <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x3 <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x1 <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x45 <4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x0 <4>scsi0:A:0:0: INITIATOR_MSG_OUT PHASEMIS in Message-in phase <4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x1 <4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x3 <4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x1 <4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x45 <4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x0 <6> target0:0:0: wide asynchronous <4>scsi0:A:0:0: INITIATOR_MSG_IN PHASEMIS in Command phase <4>Machine check in kernel mode. <4>Caused by (from SRR1=49030): Transfer error ack signal <4>Oops: Machine check, sig: 7 [#1] <4> <4>Modules linked in: aic7xxx scsi_transport_spi cpufreq_ondemand loop nfs nfs_acl lockd sunrpc sg st sd_mod sr_mod scsi_mod ide_cd cdrom <4>NIP: D21F0604 LR: D20D9494 CTR: D21F05EC <4>REGS: cf80d9f0 TRAP: 0200 Not tainted (2.6.18-rc6-20060905-default) <4>MSR: 00049030 <EE,ME,IR,DR> CR: 22022242 XER: 00000000 <4>TASK = cf7e8760[963] 'insmod' THREAD: cf80c000 <6>GPR00: 000000FF CF80DAA0 CF7E8760 CEA58400 CF80DA6C CEA58000 CEA58100 00000000 <6>GPR08: 00000001 D105C000 CF6E3C00 00000000 2155D240 100290EC 0000000F D22C0498 <6>GPR16: 0000001E D229F258 C373D500 D229F230 CEA589CC CEA58818 CEA588BC CEA58400 <6>GPR24: CEA58800 CEA589A0 FFFFFFFF C37C2000 CEA589A0 CEA58800 CEA59C00 CEA58C00 <4>NIP [D21F0604] ahc_linux_get_signalling+0x18/0xa8 [aic7xxx] <4>LR [D20D9494] spi_dv_device+0x338/0x51c [scsi_transport_spi] <4>Call Trace: <4>[CF80DAA0] [D20D9364] spi_dv_device+0x208/0x51c [scsi_transport_spi] (unreliable) <4>[CF80DAF0] [D21F0A6C] ahc_linux_slave_configure+0xfc/0x114 [aic7xxx] <4>[CF80DB30] [D20B71D8] scsi_probe_and_add_lun+0x8d4/0xa40 [scsi_mod] <4>[CF80DB90] [D20B78F8] __scsi_scan_target+0xd8/0x630 [scsi_mod] <4>[CF80DC20] [D20B7E9C] scsi_scan_channel+0x4c/0x9c [scsi_mod] <4>[CF80DC40] [D20B7FD4] scsi_scan_host_selected+0xe8/0x140 [scsi_mod] <4>[CF80DC70] [D21F3CA4] ahc_linux_register_host+0x344/0x35c [aic7xxx] <4>[CF80DD10] [D21F4998] ahc_linux_pci_dev_probe+0x1a8/0x1c8 [aic7xxx] <4>[CF80DD80] [C016A49C] pci_device_probe+0x6c/0xa0 <4>[CF80DDA0] [C01F0AF4] driver_probe_device+0x60/0xf4 <4>[CF80DDC0] [C01F0CC4] __driver_attach+0x8c/0xf0 <4>[CF80DDE0] [C01F0424] bus_for_each_dev+0x50/0x94 <4>[CF80DE10] [C01F0A08] driver_attach+0x24/0x34 <4>[CF80DE20] [C01F000C] bus_add_driver+0x78/0x128 <4>[CF80DE40] [C01F0FC4] driver_register+0xa0/0xb4 <4>[CF80DE50] [C016A2C8] __pci_register_driver+0x4c/0x8c <4>[CF80DE60] [D21F47D8] ahc_linux_pci_init+0x20/0x38 [aic7xxx] <4>[CF80DE70] [D105A3C0] ahc_linux_init+0x3c0/0x530 [aic7xxx] <4>[CF80DEA0] [C004EB50] sys_init_module+0x1368/0x14f8 <4>[CF80DF40] [C00125A4] ret_from_syscall+0x0/0x40 <4>--- Exception: c01 at 0xff698a4 <4> LR = 0x10001100 <4>Instruction dump: <4>38600000 4e800020 38600000 4e800020 4e800020 4e800020 814302ac 800a0000 <4>2f800000 409e0018 812a0004 8809001f <0c000000> 4c00012c 48000028 812a0004 <4> scsi0: PCI error Interrupt at seqaddr = 0x8 <4>scsi0: Signaled a Target Abort - To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
